Edco SECNG-1.5L User manual

E-SECNG-PL-1016
Printed in USA
JWA ©2016
Page 1
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LIST MANUAL
MODEL SECNG
REVISED STARTING
SERIAL # 161010019
MAGNA-TRAP™SINGLE-DISC FLOOR GRINDERS
SKU # MODEL # POWER OPTION
59800 SECNG-1.5L LEESON MOTOR 1.5HP 60Hz 1-PHASE
59900 SECNG-1.75L/50/1 LEESON MOTOR 1.75HP 50Hz 1-PHASE
™

E-SECNG-PL-1016
Printed in USA
©2016 JWA
Page 2
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY
BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.
Death or serious injury could occur if this machine is used improperly.
Extreme care must be taken when operating electric
models with water present: Ensure power cord is prop-
erly grounded, is attached to a Ground-Fault-Interrupter
(GFI) outlet, and is undamaged.
•Check all electrical cables - be sure connections are tight and
cable is continuous and in good condition. Be sure cable is
correctly rated for both the operating current and voltage of
this equipment.
•Improper connection of the equipment-grounding conductor can
result in a risk of electric shock. Check with qualied electri-
cian or service person if there is any doubt as to whether the
outlet is properly grounded. Adhere to all local codes and
ordinances.
•NOTE: In the event of a malfunction or breakdown, grounding
provides a path of least resistance for the electric current to
dissipate. The motor is equipped with a grounded plug and
must be connected to an outlet that is properly installed and
properly grounded. DO NOT modify the plug provided on the
motor. If the plug does not t the outlet have a qualied electri-
cian install the proper receptacle.
•Switch motor OFF before disconnecting power.
•Engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects or other reproduc-
tive harm.
• Gasoline is extremely ammable and poisonous.
It should only be dispensed in well ventilated areas,
and with a cool engine.
•Small gasoline engines produce high concentra-
tions of carbon monoxide (CO) example: a 5 HP 4 cycle
engine operation in an enclosed 100,000 cu. ft. area with
only one change of air per hour is capable of providing
deadly concentrations of CO in less than fteen minutes.
Five changes of air in the same area will produce noxious
fumes in less than 30 minutes. Gasoline or propane pow-
ered equipment should not be used in enclosed or partially
enclosed areas. Symptoms of CO poisoning include, head-
ache, nausea, weakness, dizziness, visual problems and
loss of consciousness. If symptoms occur - get into fresh
air and seek medical attention immediately.
SAFETY
MESSAGES
SAFETY MESSAGES
Indicates an imminent hazard which, if not
avoided, will result in death or serious injury.
Indicates an imminent hazard which, if not
avoided, can result in death or serious injury.
Indicates hazards which, if not avoided, could
result in serious injury and or damage to the
equipment.
•Safety Instructions are proceeded by a graphic alert symbol
of DANGER, WARNING, or CAUTION.
ELECTRICAL POWERED EQUIPMENT
GASOLINE/PROPANE POWERED EQUIPMENT
•Equipment should only be operated by trained personnel in
good physical condition and mental health (not fatigued). The
operator and maintenance personnel must be physically able
to handle the bulk weight and power of this equipment.
•This is a one person tool. Maintain a safe operating distance
to other personnel. It is the operators’ responsibility to keep
other people (workers, pedestrians, bystanders, etc.) away
during operation. Block off the work area in all directions with
roping, safety netting, etc. for a safe distance. Failure to do so
may result in others being injured by ying debris or exposing
them to harmful dust and noise.
•This equipment is intended for commercial use only.
•For the operator’s safety and the safety of others, always keep
all guards in place during operation.
•Never let equipment run unattended.
•Personal Protection Equipment and proper safety attire must
be worn when operating this machinery. The operator must
wear approved safety equipment appropriate for the job such
as hard hat and safety shoes when conditions require. Hear-
ing protection MUST be used (operational noise levels of this
equipment may exceed 85db). Eye protection MUST be worn
at all times.
Keep body parts and loose clothing away from moving
parts. Failure to do so could result in dismemberment
or death.
•Do not modify the machine.
•Stop motor/engine when adjusting or servicing this equipment.
Maintain a safe operating distance from ammable
materials. Sparks from the cutting-action of this machine
can ignite ammable materials or vapors.
GENERAL INSTRUCTIONS
DUST WARNING
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activi-
ties contains chemicals known to cause cancer,
birth defects, or other reproductive harm. Some
examples of these chemicals are:
•Lead from lead-based paints, and
•Crystalline silica from bricks and concrete and other
masonry products.
Your risk of exposure to these chemicals varies depending
on how often you do this type of work. To reduce your risk:
work in a well ventilated area, use a dust control system, such
as an industrial-style vacuum, and wear approved personal
safety equipment, such as a dust/particle respirator designed
to lter out microscopic particles.
•Do not disconnect power by pulling cord. To disconnect, grasp
the plug, not the cord.
•Unplug power cord at the machine when not in use and before
servicing.

E-SECNG-PL-1016
Printed in USA
JWA ©2016
Page 3
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LIST MANUAL
MODEL SECNG
MAGNA-TRAP™SINGLE-DISC FLOOR GRINDER
Section Page Number
Safety Messages and General Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
How To Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Illustration 1: Main Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5
Illustration 2: Leveling System Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Illustration 3: Water Valve & Hose Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Illustration 4: 10” Magna-Trap™ Disc Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Illustration 5: Optional Diamond Disc Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Illustration 6: Motor & Belt Drive Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 11
Wiring Diagram for Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wiring Diagram for 60Hz Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wiring Diagram for 50Hz Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Decal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Limited Equipment Warranty of Sale - Terms & Conditions . . . . . . . . . . . . . . . . . . . 16 (Back Page)
HOW TO ORDER REPLACEMENT PARTS
 To insure product safety and reliability, always use
genuine EDCO replacement parts when making
repairs to the equipment.
 When calling for parts, specify the MODEL and
SERIAL number of the machine, which can be found
on the NAME PLATE. Keep that information in the
space provided. In addition to this information, give
part number, description, and quantity as listed on
the parts list to your parts representative.
 Please note: Due to improvements and changes
in the equipment, the illustrations shown may be
di󰀨erent than the actual machine.
FILL IN INFORMATION BELOW
Date of Purchase ______________________________
Model # _____________________________________
Serial # ______________________________________
SKU # ______________________________________
TABLE OF CONTENTS

E-SECNG-PL-1016
Printed in USA
©2016 JWA
Page 4
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 1:
MAIN GROUPING

E-SECNG-PL-1016
Printed in USA
JWA ©2016
Page 5
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LISTING - ILLUSTRATION 1: MAIN GROUPING
ITEM # PART # DESCRIPTION QTY.
1 86901 MAIN FRAME, SEC-NG 1
2 86304S HANDLE BAR, SEC 1
3 10029 SCREW, CAP 3/8-24 X 1-3/4 4
4 10025 WASHER, FLAT 3/8 SAE ZINC 8
5 10004 NUT, HEX LOCK 3/8-24 ZINC 4
6 10608 GRIP, HAND 1” MODEL AT 2
7 86419 HOLDER, POWER CORD 1
8 10846 SCREW, CAP STSHW 1/4-20 X 1/2 2
9 10038 WASHER, LOCK 1/4 ZINC 2
10 86347 BRACKET, MULTI-VAC PORT 2-3” 1
11 65021 CAP/PLUG 2” RED PLASTIC, FLANGED 1
12 10846 SCREW, CAP STSHW 1/4-20 X 1/2 2
13 10038 WASHER, LOCK 1/4 ZINC 2
14 77113 HOSE, FLEX 2”ID X 32”L, GRINDERS 1
15 10766 CLAMP, HOSE, SAE #32, ADJ. TO 2-1/2 2
16 86426K RUBBER SKIRT W/ VELCRO LOOP & HOOK
(INCLUDES ITEMS 17 & 18 TOGETHER)
1
17 86426 RUBBER SKIRT W/ VELCRO-LOOP ONLY, 2 X 39-1/8
NOTE: CUT TO 36”
1
18 86427 VELCRO-HOOK ONLY, 1” X 39” (CUT DOWN)
NOTE: THIS PIECE IS PLACED AROUND THE BOTTOM EDGE
OF THE SHROUD.
1
19 77008 BEARING, BALL 1” 4-HOLE FLANGE, ND 2
20 10003 SCREW, CAP 7/16-20 X 1-1/4 ZINC 8
21 10450 WASHER, LOCK 7/16 ZINC 8
22 10481 NUT, HEX 7/16-20 ZINC 8
23 86393 SHAFT, SEC-HD 1”DIA. X 9-11/16”L 1
24 86903 SPACER, HEAD, 1-5/8”L, SEC-NG 1
25 86391A 10” MAGNA-TRAP DISC ASSY. W/ HUB
(REFER TO ILLUS. 4 FOR BREAKDOWN)
1
26 10007 PIN, ROLL 3/8 X 2-1/2 1
27 86902 HOOD, SEC-NG 1
28 10907 SCREW, CAP 3/8-16 X 3/4 2
29 10811 WASHER, LOCK 3/8 ZINC 2
30 10025 WASHER, FLAT 3/8 SAE ZINC 2
31 86345 WEIGHT BLOCK, 30 LB. 1
32 10323 SCREW, CAP 1/2-13 X 2-1/2 2
33 10045 WASHER, LOCK 1/2 ZINC 2

E-SECNG-PL-1016
Printed in USA
©2016 JWA
Page 6
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 2: LEVELING SYSTEM GROUPING
ITEM # PART # DESCRIPTION QTY.
186905 KNOB, WHEEL HEIGHT CONTROL 1
214023 KNOB, BALL 1-3/8 W/ 1/2-13THD, 1
310411 SCREW, SKT. HD. CAP 1/2-13 X 4 1
450550 SLEEVE, BRASS 1/2” TAPERED 1
580009 BEARING, BALL 5/8” 2-HOLE 1
655010 SPACER, HANDWHEEL 5/8”ID X3/4”L 1
710046 NUT, HEX 5/8-11 ZINC 1
810412 BOLT, CARRIAGE 1/4-20 X 1 2
910861 NUT, KEPS LOCK 1/4-20 ZINC 2
10 86702 FORK 1
11 10355 SCREW, CAP 1/2-13 X 11 1
ITEM # PART # DESCRIPTION QTY.
12 10312 WASHER, FLAT 1/2 SAE ZINC 2
13 10407 NUT, HEX LOCK 1/2-13 ZINC 1
14 86705 SPACER 2-9/16”L, WHEEL 2
15 79013SH WHEEL, STL.HUB 8 X 2-1/2 X 3/4”B 2
16 10428 COLLAR, LOCKING 3/4”ID 2
17 86904 LINKAGE, FORK, SEC-NG 1
18 10329 SCREW, CAP 1/2-20 X 6 1
19 10205 NUT, HEX LOCK 1/2-20 ZINC 1
20 59117 LEVEL, SCREW ON 1
21 11871 SCREW, MACHINE FHP 8-32 X 1-1/4 2
22 10462 NUT, KEPS LOCK 8-32 ZINC 2

E-SECNG-PL-1016
Printed in USA
JWA ©2016
Page 7
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ITEM # PART # DESCRIPTION QTY.
1 80021 CONN., SWIVEL FEM. 3/4HOSE X 1/2MPT 1
2 10711 VALVE, BALL 1/2 FPT 1
3 50075 BARB, 3/8 HOSE X 1/4MPT (BRASS) 1
4 50069 CLAMP, HOSE, SAE #6, ADJ. TO 13/16 2
5 86424 HOSE 3/8”ID X 20”L, SEC 1
6 11562 BARB ELBOW 90, 3/8HOSE X 1/8MPT BRASS 1
7 10864 NUT 1/8-27 PIPE THREAD (BRASS) 1
ILLUSTRATION 3:
WATER VALVE & HOSE GROUPING

E-SECNG-PL-1016
Printed in USA
©2016 JWA
Page 8
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ITEM # PART # DESCRIPTION QTY.
1-10 86391A 10” MAGNA-TRAP DISC ASSY. W/ HUB
(INCLUDES ALL ITEMS 1 THRU 10)
1
1 86391 10” MAGNA-TRAP DISC W/ MAGNETS
(INCLUDES ITEMS 1A, 1B AND 1C)
1
1A 36064 MAGNET, NEODYMIUM RING 7/8 X 1/8 3
1B 10647 SCREW, FLAT HD PHILLIPS 8-32 X 1/2 3
1C 10462 NUT, KEPS LOCK 8-32 ZINC 3
2 10112 RING, RUBBER, 4-1/2”OD X 1/2”THK 2
3 77020 RING, HUB CARRIER, 6-HOLE 1
4 77010 HUB, ALUMINUM 6-HOLE (GRINDER) 1
5 10354 SCREW, SKT. HD. CAP 3/8-24 X 1-3/4 3
6 10012 SCREW, SKT. HD. CAP 3/8-24 X 2 3
7 10113 SPACER, STEEL 9/16OD X 3/8ID X 7/32 3
8 10011 SPACER, STEEL 5/8OD X 3/8ID X 3/8T 6
9 10058 NUT, HEX LOCK 3/8-24 W/ NYLON PATCH 3
10 11725 NUT, HEX JAM 3/8-24 ZINC (USE RED LOCTITE) 3
™
ILLUSTRATION 4:
10” MAGNA-TRAP™ DISC ASSEMBLY
PART # 86391A

E-SECNG-PL-1016
ILLUSTRATION 5:
OPTIONAL DIAMOND DISC ADAPTER
ITEM # PART # DESCRIPTION QTY.
1 77618 ADAPTER, DIAMOND DISC (INCLUDES ITEM 2) 1
2 10855 SCREW, SKT. BUTTON HD 3/8-24 X 1 3
3 86108 SCREW, FLAT HD SKT 3/8-24 X 3/4 (NOT INCLUDED) -
4 86391A 10” MAGNA-TRAP DISC ASSY. W/ HUB (NOT INCLUDED) -
5 - - - - - DIAMOND DISC (NOT INCLUDED)
REFER TO PRODUCT CATALOG FOR OPTIONS.
-
Printed in USA
JWA ©2016
Page 9
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
MAGNA-TRAP™
DISC ASSEMBLY
10” BOLT-ON
DIAMOND DISC

E-SECNG-PL-1016
Printed in USA
©2016 JWA
Page 10
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
ILLUSTRATION 6: MOTOR & BELT DRIVE GROUPING

E-SECNG-PL-1016
Printed in USA
JWA ©2016
Page 11
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
PARTS LISTING - ILLUSTRATION 6: MOTOR & BELT DRIVE GROUPING
ITEM # PART # DESCRIPTION QTY.
116077
16178.....
16174.....
16179.....
16060
16191
16183
16133
MOTOR, 1.5HP-1PH-60HZ-1725RPM-115/230V-13/6.5A
LEESON CAT. NO. 113769.00 WATT-SAVER
REPLACEMENT PARTS:
.....CAPACITOR, START, LEESON 003025.15 (500MFD 125V)
.....CAPACITOR, RUN, LEESON 003014.02 (50MFD 240V)
.....RESET BUTTON, LEESON 300033.02 (CED2705)
MOTOR, 1.75HP-1PH-50HZ-1425RPM-110/220V
LEESON CAT. NO. 117051.00 RED FARM-DUTY
REPLACEMENT PARTS:
.....CAPACITOR, START, LEESON 003025.11 (650MFD 125V)
.....CAPACITOR, RUN, LEESON 003014.13 (65MFD 240V)
.....RESET BUTTON, LEESON 300117.04 (BRJ42DA)
1
1
1
1
1
1
2
1
2 86404 MOUNT, MOTOR 1
3 10806 SCREW, CAP 5/16-18 X 1 4
4 10213 WASHER, FLAT 5/16 SAE ZINC 4
5 10801 WASHER, LOCK 5/16 ZINC 4
6 10054 NUT, HEX 5/16-18 ZINC 4
7 10055 SCREW, CAP 3/8-16 X 1 4
8 10811 WASHER, LOCK 3/8 ZINC 4
9 10025 WASHER, FLAT 3/8 SAE ZINC 4
10 3613
77017
SHEAVE 3”OD X 1GR.B X 5/8”BORE (60 Hz MOTOR)
SHEAVE 3”OD X 1GR.B X 7/8”BORE (50 Hz MOTOR)
1
1
11 ----- KEY 3/16”SQ. X 1-3/8 (INCLUDED W/ MOTOR) 1
12 10290 BELT B-35 1
13 86009 SHEAVE 9” OD X 1GR.B X 1” BORE 1
14 40317 KEY 1/4SQ X 1-5/8 1
15 77042 BRACKET, LOVATO ROTARY CAM SWITCH 1
16 10846 SCREW, CAP STSHW 1/4-20 X 1/2 2
17 10038 WASHER, LOCK 1/4 ZINC 2
18 11663 SCREW, MACHINE 8-32 X 1/2 RHCD ZINC 4
19 10462 NUT, KEPS LOCK 8-32 ZINC 4
20 77043
77043-2.....
77043-4.....
SWITCH, ROTARY CAM ON/OFF, LOVATO
REPLACEMENT PARTS:
.....SWITCH HANDLE, PADLOCKABLE, LOVATO
.....GASKET RING, OPERATOR, LOVATO
1
1
1
21 77043-1 SWITCH ADAPTER, PG16 TO 1/2”NPT 2
22 40066 STRAIN RELIEF 1/2NPT X .350-.450” 2
23 11690 CLAMP, LOOM, 3/8” 1
24 77045 WIRE HARNESS 12/3 X 42”LOA 1
25 16176 STRAIN RELIEF 3/4NPT X .350-.450” 1
26 10740 CONDUIT LOCK NUT 3/4 NP (LOCATED INSIDE JUNCTION BOX) 1
27 11565 CLAMP, LOOM, 5/8” (SAE SIZE 10) 2
28 86422 CORD W/ PLUG, 25FT. POWER, STRAIGHT STYLE PLUG 1

E-SECNG-PL-1016
Printed in USA
©2016 JWA
Page 12
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
WIRING DIAGRAM FOR SWITCH

E-SECNG-PL-1016
Printed in USA
JWA ©2016
Page 13
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
WIRING DIAGRAM FOR 60Hz MOTOR
LEESON CAT. NO. 113769.00
USE CONNECTIONS FOR CLOCK-WISE (C.W.) ROTATION SHOWN BELOW IN CHART
MOTOR CORD: BLACK WIRE - L1, WHITE WIRE - L2, GREEN WIRE - GROUND
LOW VOLT (115V) STANDARD, HIGH VOLT (230V) OPTIONAL

E-SECNG-PL-1016
Printed in USA
©2016 JWA
Page 14
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
WIRING DIAGRAM FOR 50Hz MOTOR
LEESON CAT. NO. 117051.00
USE CONNECTIONS FOR CLOCK-WISE (C.W.) ROTATION SHOWN BELOW IN CHART
MOTOR CORD: BLACK WIRE - L1, WHITE WIRE - L2, GREEN WIRE - GROUND
LOW VOLT (110V) STANDARD, HIGH VOLT (220V) OPTIONAL

E-SECNG-PL-1016
Printed in USA
JWA ©2016
Page 15
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
DECAL SHEET

E-SECNG-PL-1016
Printed in USA
©2016 JWA
Page 16
EQUIPMENT DEVELOPMENT COMPANY, INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: [phone] or 301-663-1600 • Fax: [phone] or 301-663-1607
Website: www.edcoinc.com • E-mail: [email protected]
Equipment Development Company, Inc. herein referred to as EDCO (Seller) warrants that
each new unit manufactured by EDCO to be free from defects in material and workmanship
in normal use and service for a period of (1) one year (except for the cutter drum assembly
on all model concrete/asphalt planes, in which case the warranty period shall be 90 days)
from date of shipment to the original retail or equipment rental center owner.
Accessories or equipment furnished and installed on the product by EDCO but manufactured by
others, including, but not limited to engines, motors,electrical components, transmissions etc.,
shall carry the accessory manufacturers own warranty.
EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by
EDCO, any part which shall appear to the satisfaction of EDCO inspection to have been
defective in material or workmanship.
EDCO reserves the right to modify, alter and improve any part or parts
without incurring any obligation to replace any part or parts previously sold without such
modified, altered or improved part or parts.
This warranty is in lieu of and excludes all other warranties, expressed, implied, statutory,
or otherwise created under applicable law including, but not limited to the warranty of
merchantability and the warranty of fitness for a particular purpose in no event shall seller
or the manufacturer of the product be liable for special, incidental, or consequential dam-
ages, including loss of profits, whether or not caused by or resulting from the negligence
of seller and/or the manufacturer of the product unless specifically provided herein. In ad-
dition, this warranty shall not apply to any products or portions there of which have been
subjected to abuse, misuse, improper installation, maintenance, or operation, electrical
failure or abnormal conditions and to products which have been tampered with, altered,
modified, repaired, reworked by anyone not approved by seller or used in any manner
inconsistent with the provisions of the above or any instructions or specifications provided
with or for the product.
FORCE MAJEURE
Seller’s obligation hereunder are subject to, and Seller shall not be held responsible for, any
delay or failure to make delivery of all or any part of the Product due to labor difficulties,
fires, casualties, accidents, acts of the elements, acts of God, transportation difficulties,
delays by a common carrier, inability to obtain Product, materials or components or qualified
labor sufficient to timely perform part of or all of the obligations contained in these terms
and conditions, governmental regulations or actions, strikes, damage to or destruction in
whole or part of manufacturing plant, riots, terrorist attacks or incidents, civil commotions,
warlike conditions, flood , tidal waves, typhoon, hurricane, earthquake, lightning, explosion
or any other causes, contingencies or circumstances within or without the United States not
subject to the Seller’s control which prevent or hinder the manufacture or delivery of the
Products or make the fulfillment of these terms and conditions impracticable. In the event
of the occurrence of any of the foregoing, at the option of Seller, Seller shall be excused
from the performance under these Terms and Conditions, or the performance of the Seller
shall be correspondingly extended.
This document sets forth the terms and conditions pursuant to which the purchaser (“Pur-
chaser”) will purchase and Equipment Development Co.Inc. (“Seller”)will sell the products,
accessories, attachments (collectively the Products “) ordered by the Purchaser. These
terms and conditions shall govern and apply to the sale of Seller’s Products to Purchaser,
regardless of any terms and conditions appearing on any purchase order or other forms
submitted by Purchaser to Seller, or the inconsistency of any terms therein and herein.
1. PRICE
All prices set forth on any purchase order or other document are F.O.B. Sellers facility or dis-
tribution point, as may be determined by Seller (F.O.B.Point). All prices are exclusive of any
and all taxes, including, but not limited to, excise, sales, use, property or transportation taxes
related to the sale or use of the Products, now or hereafter imposed, together with all penalties
and expenses. Purchaser shall be responsible for collecting and/or paying any and all such
taxes, whether or not they are stated in any invoice for the Products. Unless otherwise speci-
fied herein, all prices are exclusive of inland transportation, freight, insurance and other costs
and expenses relating to the shipment of the Products from the F.O.B. point to Purchaser’s
facility. Any prepayment by Seller of freight insurance and other costs shall be for the account
of Purchaser and shall be repaid to Seller.
2. PAYMENT TERMS
Payment terms are as follows. 2% 10 days (to approved and qualified accounts). Net 30
days. This is a cash discount for invoices paid within 10 days after the invoice date, regard-
less of date of receipt of shipment. This is not a trade discount and will not be granted to
accounts that do not adhere to stated terms.
*All past due accounts are subject to a late payment fee of 1.5% per month or a maximum
allowed by law if different, along with the expenses incidental to collection including reason-
able attorney’s fees and costs.
*Seller reserves the right to hold shipments against past due accounts.
*Seller reserves the right to alter payment terms.
3. FREIGHT TERMS
All shipments will be made F.O.B. shipping point as designated in these Terms and Condi-
tions, and title shall pass at the F.O.B. point. Delivery to the initial common carrier shall
constitute delivery to the Purchaser. Any claims for loss or damage during shipment
are to be filed with carrier by the Purchaser. Seller will not assume responsibility for the
performance of the carrier.
Back orders will be shipped in the most practical fashion with charges consistent with
our freight policy established with the original order. UPS, FED EX, MAIL or shipments
by other couriers are subject to the same terms and conditions as outlined in paragraph
#3”Freight Terms”.
4. DELIVERY, DAMAGES, SHORTAGES
Seller shall use reasonable efforts to attempt to cause the Products to be delivered as provided
for in these Terms & Conditions. Delivery to the initial common carrier shall constitute the delivery
to the Purchaser. Sellers responsibility, in so far as transportation risks are concerned ceases
upon the delivery of the Products in good condition to such carrier at the F.O.B. point and all the
Products shall be shipped at the Purchaser’s risk. Seller shall not be responsible or liable for
any loss of income and/or profits, or incidental, special, consequential damages resulting from
Seller’s delayed performance in shipment and delivery.
5. RETURN OF DEFECTIVE PRODUCTS
Defective or failed material shall be held at the Purchaser’s premises until authorization has
been granted by Seller to return or dispose of Products. Products that are to be returned
for final inspection must be returned Freight Prepaid in the most economical way. Credit
will be issued for material found to be defective upon Seller’s inspection based on prices
at time of purchase.
6. PRODUCTS ORDERED IN ERROR
Products may be returned, provided that claim is made and Seller is notified within 7 days
of receipt of Products, and the Products are in original buyer’s possession not more than
30 days prior to return, subject to Seller’s approval. If Products are accepted for return,
they must be Freight Prepaid and buyer will be charged a minimum of 15% restocking
charge, plus a charge back for outbound freight charges if the original order was shipped
prepaid. Returns are not accepted for any Products that are specifically manufactured to
meet the buyer’s requirement of either specifications or quantity.
AGREEMENTS
These Terms and Conditions constitute the entire agreement between Seller and Purchaser as
it relates to terms and conditions of sale, and supersedes any and all prior oral or written agree-
ments, correspondence, quotations or understandings heretofore in force between the parties
relating to the subject matter hereof. There are no agreements between Seller and Purchaser
with respect to the Product herein except those specifically set forth in and made part of these
terms and conditions. Any additional terms, conditions and/or prices are rejected by Seller.
These terms and conditions may be modified, cancelled or rescinded only by a written
agreement of both parties executed by their duly authorized agents.
USE ONLY GENUINE EDCO PARTS & ACCESSORIES
For your own safety, the safety of others and the life of your machine.
Equipment Development Company, Inc.
LIMITED EQUIPMENT WARRANTY OF SALE - TERMS & CONDITIONS