EdilKamin KIRA Quick start guide

KIRA - VYDA
EN Installation, use and maintenance page 2
PELLET STOVE

2
ENGLISH
The undersigned EDILKAMIN S.p.A., with registered office in
Via Vincenzo Monti 47 - 20123 Milan (Italy) - Tax ID Code and
VAT number 00192220192
Hereby declares, under its sole responsibility, that:
The pellet stove mentioned below complies with EU
Regulation 305/2011 and the harmonised EU standard
EN 14785:2006
PELLET STOVE, trade name EDILKAMIN, model KIRA -
VYDA
SERIAL NO.: Rating plate reference
KIRA - VYDA: Performance declaration: (DoP - EK No. 160):
Moreover, the company hereby declares that:
the KIRA - VYDA wood pellet stove satisfies the requirements
of the following European directives:
2014/35/EU - Low Voltage Directive
2014/30/EU - Electromagnetic Compatibility Directive
Introduction and who the manual is for 3
Safety information 4
Dimensions 5
Technical data 7
Unpacking 8
Installation 10
Fitting the cladding Kira 9
Fitting the cladding Vyda 20
Instructions for use 26
Maintenance 36
Troubleshooting 41
CONTENTS
USER/INSTALLER
Edition in English translated from the original version in Italian

3
ENGLISH
Dear Sir/Madam
We thank you for and congratulate you on choosing our
product. Before using it, we would ask you to read this
manual carefully, so that you can make the most of all its
functions in total safety.
This manual is an integral part of the product. We ask you
to keep it for the entire lifetime of the product. If you lose it,
you can request a copy from your dealer or download it from
www.edilkamin.com.
Readers of the manual
This manual is addressed to:
• those who use the product at home (“USER”);
• the technician who will install the product (“INSTALLER”)
The target person of each page is indicated in a band at the
bottom of the page (USER or INSTALLER).
General information
After unpacking the product, check the condition and
completeness of the contents.
In the event of error, immediately contact the retailer where
the purchase was made, providing him with a copy of the
warranty booklet and sales receipt.
The appliance must be installed and operated in compliance
with local and national law and European regulations. For the
installation, and for anything not specifically indicated in the
manual, observe local regulations.
The diagrams provided in this manual are for illustration
purposes only: they do not always strictly refer to your
specific model, and are not binding in any way.
MEANING OF SYMBOLS
In some parts of the manual the following symbols are
used:
INFORMATION:
failure to comply with these requirements
will compromise product use.
PLEASE NOTE:
carefully read and understand the
message in question, since failure to
follow the instructions in it could cause
serious damage to the product and put
the safety of those using it at risk.
OPERATING SEQUENCE:
follow the instructions for the operations
described.
Product identification and warranty.
The product is uniquely identified by a number, the
“counterfoil”, which is indicated on the warranty certificate.
Please keep:
• the warranty certificate accompanying the product
• the purchase receipt given to you by the retailer
• the declaration of conformity given to you by the installer.
The warranty conditions are given in the warranty certificate
accompanying the product.
First ignition is required, in Italy, by an authorised
technician in accordance with UNI 10683, and is
recommended in all countries to ensure best results from
the product.
This consists of:
• checking the installation documents (declaration of
conformity) and the quality of the installation itself
• calibrating the product to suit its actual application
• providing explanations to the end user and issuing
the complementary documentation (first ignition -
commissioning certificate)
Having the appliance commissioned properly ensures that it
will operate to best effect and in complete safety.
First ignition is required for activation of the Edilkamin
manufacturer warranty. The warranty is only valid in the
country where the product was bought.
If the appliance is not commissioned by an authorised
technician, Edilkamin will not provide warranty service. See
the warranty booklet for details. The above terms do not
affect the dealer’s legal responsibility for the legal warranty.
The warranty, however, covers only demonstrable
manufacturing defects and not, for instance, problems
resulting from improper installation or calibration.
USER/INSTALLER

4
ENGLISH
SAFETY INFORMATION
• The product is not designed for use by people,
including children, with limited physical, sensory
and mental abilities.
• The appliance is not designed for cooking
purposes.
• The appliance is designed to burn UNI EN ISO
17225-2 category A1 wood pellets, in the amounts
and manner described in this manual.
• The appliance is designed for indoor use and in
areas with normal humidity conditions.
• Keep the product in a dry place out of the weather.
• For the legal and company warranties, refer to the
warranty certificate inside the product: specifically,
neither Edilkamin nor the retailer are liable for
damage resulting from incorrect installation or
maintenance.
Safety risks may be caused by:
• Installation in non-suitable settings, in particular
those that are subject to fire risks. DO NOT
INSTALL THE PRODUCT IN AREAS SUBJECT TO
THE RISK OF FIRE.
• Contact with fire and hot parts (e.g. glass panel
and pipes). DO NOT TOUCH HOT PARTS and,
when the stove is switched off and still hot, always
wear the glove supplied.
• Contact with live electrical equipment (internal).
DO NOT ACCESS THE INTERNAL ELECTRICAL
EQUIPMENT WHILE THE APPLIANCE IS
POWERED ON. Electrocution hazard.
• Use of improper ignition aids (e.g. alcohol). DO
NOT IGNITE OR BOOST THE FLAME WITH FLUID
SPRAYS OR A FLAME TORCH. Serious risk of
burns, damage and injury.
• Use of fuel other than wood pellets. DO NOT BURN
WASTE MATTER, PLASTIC OR MATERIALS OTHER
THAN WOOD PELLETS IN THE COMBUSTION
CHAMBER. The product may become soiled, the
flue may catch fire, and environmental damage
may ensue.
• Cleaning the combustion chamber when hot. DO
NOT CLEAN WITH A VACUUM CLEANER WHEN
HOT. You could damage the vacuum-cleaner and
risk the emission of smoke in the room.
• Cleaning the smoke duct with cleaning products.
DO NOT CLEAN THE PRODUCT WITH
FLAMMABLE PRODUCTS. Risk of fire or blowback.
• Cleaning the glass pane while hot or with unsuitable
cleaning products. DO NOT CLEAN HOT GLASS
WITH WATER. ONLY USE RECOMMENDED
GLASS CLEANING PRODUCTS. Risk of cracking
and permanent, irreparable damage to the glass.
• The storage of flammable materials at a distance
which is less than the safe distances listed in
this manual. DO NOT PLACE LAUNDRY ON
THE APPLIANCE. DO NOT PLACE DRYING
RACKS WITHIN THE SAFETY CLEARANCE. Keep
flammable fluids away from the appliance. Fire
hazard.
• Blocking the aeration vents and air intakes in the
room. DO NOT BLOCK THE AERATION VENTS
OR FLUE. Risk of smoke returning into the room
with consequent damage and injury.
• Use of the product as a support or ladder. DO
NOT CLIMB ONTO THE PRODUCT OR USE IT AS
A SUPPORT. Risk of damage and injury.
• Use of the stove with the combustion chamber
open. DO NOT USE THE PRODUCT WITH ITS
DOOR OPEN.
• Incandescent material may come out from the
open door. DO NOT throw incandescent material
outside the appliance. Fire hazard.
• Use of water in case of fire. CALL THE
AUTHORITIES if a fire breaks out.
• If you have doubts, please do not take any action,
but contact the retailer or the installer.
For reasons of safety, read the user instructions
included in this manual.
USER/INSTALLER

5
ENGLISH
63
65
123,5
16 16
16
31,5 31,5
32
57
110
31
DIMENSIONS
KIRA - DIMENSIONS (cm)
Ø 8 cm
smoke outlet
Ø 4 cm
combustion air
Ø 8 cm
hot air ducting *
* accessories for ducting
hot air are available
USER/INSTALLER

6
ENGLISH
61,5
62,5
121,5
15,5 15,5
15,5
31 31
32
57
110
31
VYDA - DIMENSIONS (cm)
USER/INSTALLER
DIMENSIONS
Ø 8 cm
smoke outlet
Ø 4 cm
combustion air
Ø 8 cm
hot air ducting *
* accessories for ducting
hot air are available

7
ENGLISH
The above data is for guidance only and was measured during certification by a notified body.
EDILKAMIN s.p.a. reserves the right to modify the product without notification in the interests of improvement.
ELECTRICAL SPECIFICATIONS
Power supply 230 Vac +/- 10% 50 Hz
Mean absorbed power 35-190 W
Power absorption during ignition 520 W
Remote control frequency (provided) 2,4 GHz
Protection rating Fusibile 4 AT, 250 Vac 5x20
TECHNICAL DATA EN 14785
KIRA - VYDA
Nominal power Reduced power
Available power 14,3 4,2 kW
Efficiency 90 92,1 %
CO emissions at 13% O20,016 0,037 %
Fumes temperature 159 93 °C
Fuel consumption 3,3 1 kg/h
Tank capacity 30 kg
Draw 12 10 Pa
Autonomy 9 30 hours
Heatable volume * 375 m3
Fumes outlet diameter (male) 80 mm
Air intake diameter (male) 40 mm
Ducting diameter 80 mm
Weight with packaging 180 kg
TECHNICAL DATA FOR RATING THE FLUE
which must in any case satisfy the requirements of this sheet and the installation instructions
Nominal power Reduced power
Fumes temperature at smoke outlet 220 130 °C
Minimum draw 0,01 Pa
Fumes flow rate 7 4 g/s
* Il volume riscaldabile è calcolato con una richiesta di calore di 33 Kcal/m³ ora
TECHNICAL DATA
USER/INSTALLER

8
ENGLISH
UNPACKING
INSTALLER
1
2
PREPARATION AND UNPACKING
The packaging materials are neither toxic nor noxious
and do not require special disposal.
The user is responsible for storing, disposing of and
recycling them in a regulatory fashion.
Always move the stove in an upright
position with suitable equipment and in
observance of safety regulations.
Do not turn the package over, and handle
all parts requiring installation with care.
PACKAGING (further information in the paragraph
on linings)
The delivery consists of two packages:
• one (1) with the structure of the stove
• one (2) with the ceramic or stone cladding
In the stove package you will find:
• warranty certificate,
• glove,
• this manual,
• remote controlo;
• power cable,
• small parts for installing the lining * (further details
on the following page),
• grille of the top,
• protective lever (removable handle) for opening
the combustion chamber door.
On the top of the stove there are the components described above
The metal grille of the top is contained in package
(1) with the stove, provided with the small parts for
its installation (three M4 screws for the ceramic parts
and M6 for the stone parts, washers and rubber
buffers to be applied on top of the grille)
* Other small parts (for Vyda and Kira)
• M4 screws with washers for fixing the ceramic
parts
• M5 screws with washers for the ceramic sides of
Kira H
• M6 screws for fixing the stone parts
• cable glands for the terminal board on the rear
protective lever
grille of the top

9
ENGLISH
UNPACKING
INSTALLER
1
2
11
2
DO NOT TRY TO REMOVE THE PRODUCT FROM THE PALLET WITHOUT HAVING OPENED THE
COMBUSTION CHAMBER DOOR AND UNDONE THE SCREWS WHICH FIX IT TO THE PALLET
TO REMOVE KIRA FROM THE PALLET
To remove the stove from the pallet you must (see figures below corresponding to instructions):
1. remove the two brackets (screwed) on the front
2. remove the two brackets (screwed) on the rear of the stove
TO REMOVE VYDA FROM THE PALLET
To remove the stove from the pallet you must (see figures below corresponding to instructions):
1. open the combustion chamber door; undo the two screws holding the bottom front panel and remove it to
access the two screws which fix the product to the pallet
2. remove the two brackets (screwed) on the rear of the stove
THE DRAWINGS ARE FOR GUIDANCE ONLY,
USEFUL FOR THE INSTALLATION, BUT THEY
MAY NOT REFER TO THE SPECIFIC MODEL.
screws fixing the product to the pallet

10
ENGLISH
REMARKS ON INSTALLATION
Note that:
• installation must be carried out by authorised
technical personnel;
• The appliance must be installed and operated
in compliance with local and national law and
European regulations. The applicable Italian
regulation is UNI 10683;
• If installed in a condominium, the appliance must
be approved by the administrator.
We give some general instructions below, however
these do not obviate the need to comply with local
regulations and do not affect the installer’s liability for
the installation.
Checking the suitability of the installation
space
• The room must have a volume of at least 30 m3.
• The floor must be able to bear the weight of the
product and its accessories.
• Level the appliance.
• The appliance may not be installed in a bedroom,
bathroom or in the same room as other equipment
which draws air for combustion from the room
itself, or in any area with an explosive atmosphere.
Any extraction fans operating in the same room or
area as the product, may affect its draw.
• In Italy, check the compatibility pursuant to UNI
10683 and UNI 7129 in the presence of gas fired
products.
INSTALLATION
Protection from heat and safety clearances
The surfaces of the building adjacent to the product
must be protected against overheating.
The insulation to be used will depend on the type of
surface in question.
The appliance must be installed in accordance with
the following safety instructions:
- minimum clearance at the sides and rear of 20 cm
from flammable materials.
- no flammable materials may be kept closer to the
front of the appliance than 80 cm.
If connected to a wooden or otherwise flammable wall,
the flue must be insulated appropriately.
If installed on a flammable or combustible floor, or one
incapable of bearing its load, use steel or glass plates
under the stove to distribute the load.
Contact the retailer for such optional equipment
Positioning the product
The product is designed to operate in all climatic
conditions. In special circumstances, such as strong
wind, its safety equipment may switch the appliance
off.
Contact the authorised Edilkamin Technical Assistance
Centre.
INSTALLER

11
ENGLISH
FLUE SYSTEM
(Smoke duct, flue and chimney pot)
This chapter has been drawn up pursuant to European
regulations EN 13384, EN 1443, EN 1856 and EN
1457. The installer must observe both these and any
other local regulations. This manual does not in any
way substitute such regulations.
The product must be connected to a flue system which
ensures that the smoke produced by combustion are
discharged in complete safety.
Before positioning the appliance, the installer must
check that the flue is suitable.
SMOKE DUCT, FLUE
The smoke duct (which connects the combustion
chamber’s smoke outlet with the flue) and the flue itself
must, among other regulatory requirements:
• receive the smoke from a single product (the
outlets of multiple appliances cannot be conveyed
into a single flue)
• be routed vertically for the most part
• have no downwards sloping sections
• preferably have a circular internal cross section, or
with a ratio of the sides of less than 1.5
• terminate at roof level with a proper chimney pot:
the flue may not discharge directly on the wall
or into an enclosed space, even if the space in
question is open to the sky
• be made of material rated in fire reaction class
A1 as per UNI EN 13501 or analogous national
regulations
• be certified, with a chimney plate if metal
• be of uniform cross section or vary in cross section
only immediately after the outlet, not at some mid
point of its length.
THE SMOKE DUCT
Further to the general requirements for the smoke duct
and flue, the smoke duct:
• may not be made of flexible metal material
• must be insulated, if routed through unheated
areas or outdoors
• must not be routed through rooms where the
installation of combustion heat generators is
prohibited, there is risk of fire, or which cannot be
inspected
• must enable the recovery of soot and be open for
inspection
• have at most 3 bends with a maximum angle of
90°
• must have a single horizontal section with a length
of no more than 3 metres, depending on the draw.
Note, in any case, that long sections promote the
accumulation of dirt and are harder to keep clean.
INSTALLATION
INSTALLER

12
ENGLISH
THE FLUE:
Further to the general prescriptions for the smoke duct
and flue, the flue:
• must serve solely to discharge smoke
• must be correctly sized to satisfy the requirements
of smoke discharge (EN 13384-1)
• should preferably be insulated, in steel with a
circular internal section. If rectangular, the corners
must have a radius of not less than 20 mm, with a
ratio of the internal dimensions of <1.5
• must normally be at least 1.5 metres in vertical
length
• must have a constant cross section
• must be waterproof and thermally insulated to
ensure a good draw
• must preferably have a collection chamber for
non-combusted matter and any condensation.
• if pre-existing, must be clean, to prevent fire
hazards
• in general, we recommend fitting a tube inside the
existing masonry chimney if its diameter is greater
than 150 mm.
INTUBATED SYSTEM:
Further to the general prescriptions for the smoke duct
and flue, the intubated system:
• must operate in negative pressure
• must be open to inspection
• must observe local regulations.
THE CHIMNEY POT
• must be windproof
• must have an internal cross section equivalent to
that of the flue and a smoke outlet at least double
that of the interior of the flue
• for dual flues (which should be spaced at least 2 m
apart) the chimney pot receiving the smoke from
the solid fuel appliance or that from the higher
storey, must be at least 50 cm higher than the other
• it must extend beyond the back flow zone (in Italy,
refer to UNI 10683 point 6.5.8.)
• it must allow for maintenance of the chimney
EXTERNAL AIR INTAKE
In general, we suggest two ways to ensure a proper
flow of combustion air.
Indirect air intake
Install an air outlet at floor level with an effective sur-
face area (net of the screen or other protections) of at
least 80 cm2(10 cm in diameter).
To prevent draughts, we recommend installing the air
intake behind the stove or behind a radiator.
Installing it in front of the appliance will create
unpleasant draughts.
Direct air intake*
Install an air intake with effective area (net of the mesh
or other protective equipment) at least equal to that of
the air intake at the rear of the product.
Connect the air intake to the appliance’s air intake
with a tube (which may also be flexible). Increase the
diameter of the pipe if it is not smooth: assess its load
loss.
A maximum length of 1 metres is recommended,
without bends.
The air may be drawn from an adjacent room only if:
• the flow is taken from permanent and unobstructed
openings communicating with the outdoors;
• the adjacent room is never in underpressure
relative to the outdoors;
• the adjacent room is not a garage. subject to fire
hazard, a bathroom or bedroom;
• the adjacent room is not a shared room in the
condominium.
In Italy, UNI 10683 provides that ventilation is sufficient
even if a pressure difference between the outdoors
and indoors of no more than 4 PA is guaranteed (UNI
EN 13384-1). The installer who issues the declaration
of conformity is responsible for ensuring these
conditions.
*The direct connection of the air intake does not make
the product airtight. It is therefore necessary to ensure
an air recovery taken in the room by the product (i.e.
for the glass cleaning)
INSTALLATION
INSTALLER

13
ENGLISH
INSTALLER
Ducting of heating air
To duct the warm air exiting the rear, you will find several
optional extras at your dealer’s.
For Ø 6 cm ducting and with Edilkamin
vents:
• adapter from Ø 8 cm to Ø 6cm
• air duct pipe (3 metres, 6 cm diameter)
• “Y” junction for ducting pipe (6 cm diameter) to
deliver the output air from an outlet hole in the
stove to two rooms
• various models of ducting vents (Bent, Split,
Origami, Sharp).
The instructions for connecting these vents are given
in the manual provided with the vents.
For Ø 8 cm ducting with Edilkamin Kit 12-
12bis
• kit 12 for ducting into an adjacent room (pipe Ø 8
cm -3 m in length, B4 terminal vent; clamp)
• kit 12bis for ducting into a distant room (pipe Ø 8
cm -6 m in length, B4 terminal vent; 2 clamps; 2
wall collars)
INSTALLATION
In the “Instructions for use” paragraph, we describe
the fan settings and air directions.

14
ENGLISH
morsettiera
INSTALLATION
INSTALLER
CHECKINGTHE ELECTRICALCONNECTIONS
(the power socket must be located in an
easy to access position)
The stove is equipped with an electrical power cord
or connection to a 230V 50 Hz socket, preferably with
electromagnetic switch.
Variations in voltage of more than 10% can compromise
the operation of the stove.
The electrical system must be compliant; check the
operation of the earth in particular.
Edilkamin is not responsible for malfunctions resulting
from an improperly earthed system.
The power line must be of adequate section for the
power of the appliance.
The power cable must not come into contact with the
flue or other hot parts of the stove.
Power up the stove by setting its switch from 0 to 1.
There is one 4 A fuse on the socket with switch located
at the rear of the stove.
switch
fuse housing
power supply
HOOKING UP OPTIONAL COMPONENTS
The product is fitted with a terminal block. 5 and 6
(AUX) can be used to hook up a thermostat or other
device requiring a voltage-free contact.
123456
Only for Technical Edilkamin AUX

15
ENGLISH
KIRA - CLADDING
Description Reference in Figures below Quantity
Bottom front panel (1) n°1
Top front panel (2) n°1
Top right ceramic side (3) n°1
Lower right ceramic side (4) n°1
Lower left ceramic side (5) n°1
Top left ceramic side (6) n°1
Ceramic top (7) n°1
INSTALLER
7
7
1
2
1
23,4,5,6
3
4
3
5
6
The position of each ceramic side is indicated on the interior part of each piece (example INF.DX means bottom right.)
The metal grille of the top is in the package of the stove structure together with the M4 screws, fixing washers and the
two rubber buffers to be applied on top of the grille
* Small parts to be used for Kira :
• M4 screws with washers for fitting the ceramic front parts
• M5 screws and washers for fitting the ceramic sides
• cable glands for the terminal board on the rear
THE DRAWINGS ARE FOR GUIDANCE ONLY, USEFUL FOR THE INSTALLATION, BUT THEY MAY
NOT REFER TO THE SPECIFIC MODEL.

16
ENGLISH
KIRA - CLADDING
INSTALLER
1. Open the combustion chamber door with the
protective lever (removable handle P) and undo two
screws to remove the bottom metal front panel
2. Fit the ceramic part on the bottom metal front panel
using the M4 screws with washers
Fitting of the bottom front panel (1)
P
3. Screw the bottom metal front panel - 1(with the
bottom ceramic front panel already fitted) to the stove.
You can adjust the position of the front panel horizontally
to align it to the door, by moving the screws in the slots
1
1
1
1
2
3
Do not force the screw into the pin, it may
break
THE DRAWINGS ARE FOR GUIDANCE ONLY,
USEFUL FOR THE INSTALLATION, BUT THEY
MAY NOT REFER TO THE SPECIFIC MODEL.

17
ENGLISH
KIRA - CLADDING
INSTALLER
Fitting of the top front panel (2)
1. Undo the two upper screws.
3. Place the top ceramic front panel (2) on the metal
support (S).
Fit the front panel (2) with the M4 screws provided with
washers
4. Replace the support with the ceramic part and
screw it back to the structure by using the two screws
removed in point 1
To make alignment adjustments between ceramic/
stone and the door, you can use the top screws.
Left/right adjustments can be made.
Close the combustion chamber door and check the
alignments.
2. Remove the metal support (S).
1
S
S
S
2
2
3

18
ENGLISH
THE DRAWINGS ARE FOR GUIDANCE ONLY,
USEFUL FOR THE INSTALLATION, BUT
THEY MAY NOT REFER TO THE SPECIFIC
MODEL.
KIRA CLADDING
INSTALLER
1. Place the rubber buffers and hook the bottom side
ceramic part to the structure.
Fitting the ceramic sides (3,4,5,6)
The sides are hooked and screwed on top
Start from the bottom ceramic part of one of the two sides.
To make alignment adjustments between ceramic/
stone and the door, you can move the top or bottom
screws in their slots.
The top screws allow the alignment with the top.
The bottom screws allow the alignment with the front
panel and with the bottom side panel. If the ceramic or
stone side is not aligned, remove it, adjust the screws
and put it back.
4
2. Screw on the sides from above with the M5 screws
and the washers provided
1
2
3
rubber buffers
M5 screw
and washer
M5 screw and
washer
There are some other
screws on the brackets
that you can use for any
adjustment
rubber buffers
Take care that the side ceramic tile does not
knock against the metal side when opening
the door. If necessary adjust the setting to
avoid breakage

19
ENGLISH
KIRA - CLADDING
INSTALLER
Fitting the ceramic top (7)
The top part of the lining consists of a grille (G) for the hot
air output and the stone or ceramic top (4).
Adjustments can be made by adjusting the feet
supporting the top, or the screws under the sides,
as shown in the fitting of the sides (with top and side
removed)
2. Place the grille under the ceramic or stone part and fit
it with the M4 screws provided
7
G
1. Fit the two rubber buffers provided on the top part of
the grille. They can also be fitted after the grille has been
matched with the top
3. Open the lid of the pellet tank, place the grille and
ceramic top (after screwing them together) onto the stove
rubber buffers
1
7
G
2
3

20
ENGLISH
VYDA - CLADDING
Description Reference in the
Figure below
Quantity
Front panel above the door (ceramic or stone) (1) 1
Top front panel (ceramic or stone) (2) 1
Left or right interchangeable sides (ceramic or stone) (3) 2
Top (ceramic or stone) (4) 1
INSTALLER
1
3
3
4
2
The metal grille of the top is in the stove structure package together with the M4 screws (and M6 for the stone top),
the fitting washers and the two rubber buffers
* Small parts to be used for Vyda :
• M4 screws with washers for fixing the ceramic parts
• M6 screws for fixing the stone parts
• cable glands for the terminal board on the rear