Elite Screens AR100H2 User manual

V051616-EA
EDGE FREE
Applies to all available screen materials:
Product Description: The Aeon
Series is a fixed frame projection
technology. The EDGE FREE® des
ign resembles a giant size flat
an installation option to further enhance the frame appearance and
backlighting kit is available
for added visual appearance
Assembly Video:
For further assistance, watch our assembly and installationvideo at
www.elitescreens.com/video/aeon-
assembly
For more information on the LED kit
please visit:
Hardware and Parts List
Please make sure all parts listed below a
re included before installation
A. Elbow joint x 4 pcs
B.
D. Center joints x 2 pcs
G. M6 screw x 2-12 pcs
J. M5x50 screws/anchor x 6 pcs
M. Velvet tape
www.elitescreens.com
Aeon Series
EDGE FREE
®
Fixed Frame Projection Screen
User’s Guide
CineGrey 3D®, CineGrey and CineWhite™
Series is a fixed frame projection
screen that
uses Elite’s EDGE FREE
ign resembles a giant size flat
panel TV display.
The Aeon includes a
an installation option to further enhance the frame appearance and
ab
sorb projector overshoot
for added visual appearance
.
For further assistance, watch our assembly and installationvideo at
assembly
or scan the following QR Code:
please visit:
http://www.elitescreens.com/led
re included before installation
.
B.
Top/Bottom horizontal fame x 4 pcs C. Left/Right
vertical
E. Center Support bar x 1-2 pc F
. Wall brackets x
H. M5x15 screw x 24 pcs I.
M6x12 screw x
K. Rubber hammer x 1 pc
L. Screwdriver x
N. Corner Support Bar (180”-200”) x
4
1
Fixed Frame Projection Screen
uses Elite’s EDGE FREE
®
The Aeon includes a
velvet tape as
sorb projector overshoot
. An optional LED
vertical
frame x 2 pcs
. Wall brackets x
2-3 pcs
M6x12 screw x
2-12pcs
L. Screwdriver x
1 pc
4
pcs

V051616-EA www.elitescreens.com 2
Frame Assembly
1. Insert the center joint (D) into one of the ½ horizontal frames (B) and fasten it with the two M5x15 screws (H).
2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws.
3. Repeat steps 1 and 2 for assembling the second horizontal frame.
Push Push
4. For models 150” and below, insert and slide in oneM6 screw(G) through the channel located on the backeach
horizontal frame section (top/bottom).
Note: For models 180” and above, insert and slide in four M6 screws (two on each frame) through the channel
located on the back of each horizontal frame section(top/bottom). Insert two M6 screws on each vertical frame
section(left/right).
5. Insert the elbow joint (A) into each end of the horizontal frames(B)as shown below.
Horizontal long frame (B)
ElbowJoint
(A)
ElbowJoint
(A)
Horizontal long frame
Place one M6 hex screw (G) in the center for attaching the center support bar (E)
Face up
M6 hex screws (G)
Horizontal frame
Center Joints
Top right Frame Top left Frame

V051616-EA www.elitescreens.com 3
6. Insert the two vertical short frames (C) into the elbow joint (A).
7. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below.
Horizontal Long frame(B)
Horizontal long frame (B)
Vertical short frame (C)
push
push push
push
Vertical short frame (C)
Note: For models 180” and above,
ensure two M6 screws (G) are
inserted on each vertical frame
before proceeding to step 7.
Face up

V051616-EA www.elitescreens.com 4
8. Make sure all four corners are properly in place to form a perfect square. Then fasten the four angles with the
M5x15 Screws (H).
Screen Material Installation
1.Lay the screen material completely flat with the front facing down on a clean surface in a horizontal position. The
back side of the screen material should be placed upwards.
Note: The back side of the material has the velcro borders all around the edges.
2. Carefully and gently place the assembled frameon top the screen material as shown below. Make sure to not allow
the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.
Four corners join correctly to form a perfect
square. Use the included screwdriver (L) to
fasten the Mx15 screws (H) into each corner
by aligning the frame screw holes to the
holes in the elbow joint (A).
Screen material back facing up

V051616-EA www.elitescreens.com 5
3. After all of the corners of the frame have been properly aligned, attach the material to the frame in the following
order A→B→C→D (see instructions below for details).
Attach the screen material to the corners as shown below.
4. After all four corners have been attached; please check whether the frame corners are wrapped by the screen material.
If not, please loosen the velcro connection and repeat the above steps so the frame is not exposed.
Note: The black shaded part represents the velcro on the frame. That Velcro end will ultimately
attach with the other velcro end on the screen material.
Note:
Represents the
screen material
2) Fold over and attach
material to thevelcro
strip of the frame.
3) Fold over second side
and attach to frame
4) Repeat until all four
sides are done in the
order A, B, C, D
1) Stretch the screen
material in the direction
of the arrowhead.
D
A D
C B

V051616-EA
5. Proceed to
attach the rest of the material to the frame as describe
Grasp the middle
of the
material and attach it to the velcro
strip on the frame
Attach in the following sequence
C
www.elitescreens.com
attach the rest of the material to the frame as describe
d in the illustrations below.
Lay the Velcro end on the screen
material over the Velcro end of the
frame and keep it within the edge.
Proceed
in the following sequence
below ①
②
The key is to attach within the
middle sections of 1 and 2. Then
continue attaching the remaining
unattached areas.
Repeat
the
remaining
three sides in the
sequence A, B, C, D as show
below.
of the
screen
material and attach it to the velcro
Attach in the following sequence
: a-b-c-d
A
B
D
6
d in the illustrations below.
Lay the Velcro end on the screen
material over the Velcro end of the
frame and keep it within the edge.
in the following sequence
②
The key is to attach within the
middle sections of 1 and 2. Then
continue attaching the remaining
unattached areas.
the
same steps on
three sides in the
sequence A, B, C, D as show

V051616-EA www.elitescreens.com 7
6.If the material is too loose or tight after adjusting all four corner sides, then you will need to reattach the material.
Please follow the steps below to properly remove the screen material from the frame. This procedure will ensure
prolonging the life of the screen material.
Screen Material Removal
1. Detach the velcro from the frame.
2. Gently pull back the material to release the material from the velcro connections on the corners.
Support bar installation (for models under 180”):
1. Position the center support bar (E) in the middle of the frame and align the hole on each end of the support bar
with the M6 hex screws (G)on the top and bottom frames.Then fasten with the M6x12 screws (I).
Move the M6 hex screw (G) to the middle area of the frames.
Align the M6 screws
with the two holes.
Pull back the screen material from
the velcro connection along the
edges of the frame to detach it.
Center Support bar

V051616-EA
Support bar installation
(for models
1. Position the center support bar (E)
and
hex screws (G) in the areas
of the
shown in fig 1. Align the
hole on each end of
the support bar with the
M6 hex screws
(G)
located at the top and bottom frame
sections.Then fasten with the
M6x12 screws
(I).
2. Position the
Corner support bars (N)
fig 2. Align the holes on each end of the corner support
vertical and horizontal frame sections. Then fasten with the
Center Support Bar
Corner Support Bar
Align the M6
screws with the
two holes on the
Corner Support
Bars.
Figure 1
www.elitescreens.com
(for models
180” and above):
and
M6
of the
frame
hole on each end of
M6 hex screws
located at the top and bottom frame
M6x12 screws
Corner support bars (N)
and M6 Hex screws (G)
in the areas of the frame as shown below in
fig 2. Align the holes on each end of the corner support
bars with the M6 hex screws
vertical and horizontal frame sections. Then fasten with the
M6x12 screws (I).
Center Support Bar
Align the M6 Screws with
the two holes located on
the Center Support Bar.
Move the M6 hex screw (G)
to these areas of the frame.
8
in the areas of the frame as shown below in
bars with the M6 hex screws
located on the
to these areas of the frame.

V051616-EA www.elitescreens.com 9
Notice to Installer:
Please use the following installation instructions to obtain superior optical performance from the CineGrey 3D®
Angular Reflective ALR (Ambient Light Rejecting) Screen.
Make sure to follow these instructions in order for the CineGrey 3D® to perform correctly.
•Angular-Reflective material is not compatible with ultra/short-throw projectors
•Minimum lens throw ratio 1.5x image width
•Ambient light must not come from the same direction as the projector
Since angular-reflective means that the projected image will reflect at the mirror-opposite angle, it
is important to position the projector so that the viewer will get the best possible image.
Step 1: Establish the general “eye level” of the viewers
Step 2: Set the appropriate projection level
Step 3: Adjust the screen height level and projection angle
Input Angle (A) = Output Angle (B) aligns with the viewer’s angle
Figure 2

V051616-EA www.elitescreens.com 10
Velvet Tape Trim Installation
Attention: Installing the velvet trim will reduce the viewing size of your screen. See below illustrations for a
comparison of the viewing size of the before and after edge trim installation using the 100” &120” 16:9 diagonal
models.
100” comparison:
120” comparison:
1) Lay the assembled frame on its back on a clean surface.
2) Measure 10 mm (0.40”) from the edge of the frame to the inside of the material.
The Screen
Before installing the trim strip
After installing the trim strip
After installing the trim strip
Before installing the trim strip