Elite Screens Sable Frame B2 Series User manual

11092020JA www.elitescreens.com U-00199 1
Sable Frame B2 Series
Matte White Fixed Frame Screen
Featuring CineWhite® UHD 2
USER’S GUIDE – M Type
V 2
__________________________________________________________________________________________
Congratulations on your new Sable Frame B2 purchase! The material included is our ISF Certified CineWhite®
UHD 2which produces accurate colors in a light controlled environment which reproduces the content as the
director intended.
In order for the CineWhite® UHD 2 to maintain its projection qualities and optimum performance please refer to
the list below for proper maintenance and cleaning.
•Use a dry microfiber cloth to remove dust from the screen’s surface.
•When cleaning, use a damp microfiber cloth with warm water to remove any marks.
•Never rub or apply pressure when cleaning the surface.
•Never attempt to use any solutions, chemicals, or abrasive cleaners on the screen surface.
•In order to avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any
other sharp or abrasive objects.

11092020JA www.elitescreens.com U-00199 2
Frame Parts List
A. Vertical Frame x 2pcs
B. ½ Horizontal Frame x2 pcs
C. ½ Horizontal Frame x 2 pcs
Hardware Parts List
a. M4*4
b. D5*4
c. M4*4
d. D5*4
e.
f.
g.
h.
i.
k.
l.
o.
p.
r.
Item
Parts List
100”
110”
120”
135”
150”
a.
Center Joints- M4 (bottom position)
2
2
2
2
2
b.
Center Joints-D5 (top position)
2
2
2
2
2
c.
Elbow Joints M4 (bottom position)
4
4
4
4
4
d.
Elbow Joints D5 (top position)
4
4
4
4
4
e.
Top hanging brackets
2
2
2
2
2
f.
Bottom brackets
2
2
2
2
2
g.
M4x7 Screws
24
24
24
24
24
h.
Spring
60
66
72
80
88
i.
Pull Hook
2
2
2
2
2
k.
Wall Screws M5x50
8
8
8
8
8
l.
Hollow Wall anchors
8
8
8
8
8
o.
Center Support Bar
1
1
1
1
1
p.
White gloves
2
2
2
2
2
r.
Φ3 mm Long Iron (sides) rod /Short rod (top/bottom)
2/4
2/4
2/4
2/4
2/4
8.
C+B
B+C
A
A
Red
Black

11092020JA www.elitescreens.com U-00199 3
Frame Assembly
Step 1: Place the EPE sponge (foam)
sheet on the ground of the area where
the screen will be assembled.
Step 2: Position the pieces of the frame
on the EPE sponge in the arrangement
shown below.
Step 3: Insert center joint (a/b) connectors into one-half of the horizontal frame (B/C) and secure with the
M4x7 screws (g) as shown in the illustration below.
Tip: The center joint (b) with the larger diameter holes should be on top.
Step 4: Connect the elbow joints (c/d) to the top and bottom sections of the vertical frame. Once inserted,
connect the vertical sections to the horizontal frame sections. Make sure all holes are in alignment and the frame
pieces are flush (no gaps). They should form perfect right angles.
Tip: The elbow joint (d)with the larger diameter holes should be on top.
Step 5: Secure the elbow joints by fastening them with M4x7 screws (g), 4 at each corner.
a.
b.
d.
c.

11092020JA www.elitescreens.com U-00199 4
c
c
c
c
c
c
c
c
c
c
Screen Material
Step 6: Put on the white gloves (p) and
carefully unroll the screen material on a
clean surface from the roller to the other
side as shown below. The back side of the
screen material should be placed upwards.
Then place a bottom grommet (r) on the
screen material’s eyelet and snap in the top
grommet (s) as shown below.
Repeat the process for all eyelets.
Step7: Carefully place the screen on top of the
assembled frame as shown below.Make sure that
the angular edges of the frame are not allowed to
come into direct contact with the screen material to
avoid puncturing.
Step 8: Insert the rods (r) through the sleeves according to their corresponding lengths on each edge of the
screen as shown below. The short rods (top/bottom) will overlap to secure a firm grasp in the middle areas.
Front
Back Side
r. (Red tips)
Back Side
r. (Black tips)
Back Side
Back
Side
Go through the hole
from bottom to top

11092020JA www.elitescreens.com U-00199 5
How to attach the springs
Step 9: Hook one end of the spring and secure inside the groove of the frame, use the spring hook (i)to attach
the spring to the hole located on the screen material’s outer edge in the following order.
First connect on four corners, steps 1-4. make
sure all four corners are fixed before proceeding
with next spring.
Continue to attach the remaining springs to the material in steps 5-12 in the follow order.
Step 10: Insert the Center Support Bar (o) into the upper top groove on the back of the frame with the bottom end
near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in
alignment with the groove.
i.
h.
Diagonal Models 150” and below use 1 x Center Support Bar
o.
Spring must hook both
overlapping short rods.
1
2
4
3
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
5
6
7
8
9
10
11
12

11092020JA www.elitescreens.com U-00199 6
Installation
Step 11: Measure the overall length and
height of the frame and drill holes for the top
brackets. Line up the wall brackets with the
drilled holes on the installation location and
screw them in using a Phillips screwdriver. If
not installing into a structural wood stud, use
a hollow wall anchor then screw in the M5x50
wood screws with a screwdriver. Make sure
the brackets are leveled.
Step 12: Position the fixed frame screen onto the top wall brackets as shown below and push down at the center
of the top of the frame to secure.
Step 13: With the frame slightly tilted outward; connect the bottom brackets onto the bottom groove of the frame.
Slowly return the screen to a normal upright position. Once the screen is flush to the wall, secure the brackets to
the wall with a screw. If not installing into a structural wood stud, mark the sites where the hollow wall anchors
will be placed using the same instructions above. With the wood anchor installed, repeat the process and fasten the
brackets with the M5x50 wood screws.
For Technical Support or an Elite Screens contact in your area,
visit www.elitescreens.com
e.
k.
f.