Elkay EDFPW210C Installation manual

97014C (Rev. E - 2/04)
Installation/Care/Use Manual
Model: EDFPW210C
Composite Non-Refrigerated Fountains
To assure you install this model easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH
PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES. After installation, leave
these instructions inside the fountain for future reference.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
FIG. 2FIG. 1
NOTE: WATER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
Installer
PAGE 1

97014C (Rev. E - 2/04) PAGE 2
FIG. 4
FINISHED FLOOR
DETAIL 2
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN
C = MOUNTING HOLES FOR SECURING FOUNTAIN TO WALL
CARE AND MAINTENANCE OF ELKAY COMPOSITE FOUNTAINS
Elkay Composite fountain provides an exremely durable, nonporous surface which resists staining. Care is very simple. Routine
cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam cleaner, is all that is normally needed to give
many years of trouble free service. Cleaners left standing on the fountain surface can dull the surface finish. Be certain to rinse
all cleaning agents completely and polish with a soft cloth.
Harsh abrasive cleaners are not required and should not be used.
Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple scratches and stains.
Cigarette burns can normally be removed without noticeable effect. Deeper scratches or gouges can be corrected with fine grit
sandpaper (240 grit then 400 grit) or a green Scotchbrite pad.
To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or like products will keep the finish
looking like new.
WARNING: WALL MOUNTING SURFACE MUST BE SMOOTH AND EVEN. DISTOR-
TION TO BACK PANEL DUE TO ATTACHMENT TO AN UNEVEN SUREFACE WILL
RESULT IN DAMAGE AND/OR BREAKAGE OF THE BACK PANEL.

97014C (Rev. E - 2/04)
This page left blank intentionally.
PAGE 3

97014C (Rev. E - 2/04)
PAGE 4
PART NO.ITEM NO.
PARTS LIST
Drain
Screw - 10-24 x 1/2" PHTC
Retaining Nut
Bottom - Cover (EDFPW210JC)
Strainer - Beehive (Gold)
Hex Nut
Ferrule - Drain
Push Button - (Gold)
Push Buttton Sleeve (Gold)
Regulator Holder
Orifice Assy (Gold)
Push Button Extension
Fountain - Green Marble (EDFPW210JC)
Regulator
Tube Assy - Bubbler
Set Screw - #6-32 x 5/16"
Strainer
Threaded Insert
Bubbler Assy
Bubbler (Gold)
Gasket - Black
Locknut - 3/8 -18
Back Panel (EDFPW210JC)
Nut - Regulator Mounting
LK464
112627543890
15005C
27201C
45362C
40045C
45358C
45366C
45751C
50986C
45382C
56087C
55973C
61313C
66399C
70022C
55996C
75554C
45387C
A55139
100322740560
70012C
55978C
45736C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DESCRIPTION
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt
or not regulate. Mineral deposits may be removed from the orifice with a
small round file not over 1/8" diameter or small diameter wire.
CAUTION: Do not file or cut orifice material.
Stream Regulator: If orifice is free of material deposits, regulate flow as
in instructions on page 2 (Step 7). If replacement is necessary, see parts
list for correct regulator part number.
Actuation of Quick Connect Water Fittings: Cooler is provided with
lead-free connectors which utilize an o-ring water seal. To remove tubing
from the fitting, relieve water pressure, push in on the gray collar while
pulling on the tubing.(See Figure 2, Page 1). To insert tubing, push tube
straight into fitting until it reaches a positive stop, approximately 3/4".
TROUBLE SHOOTING & MAINTENANCE
FIG. 4
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY  2222 CAMDEN COURT  OAK BROOK, IL 60523  630.574.8484
PRINTED IN U.S.A.
15
13
1
17
2, 4, 18
5, 7
23
8
SEE FIG.
4
22
FIG. 6
BASIN
310
19
912
16
FIG. 5
6
14
20
11
21
SEE FIG. 5
NOTE: When installing replacement bubbler,
tighten nut (item 22) Only to hold parts snug in
position. DO NOT OVER TIGHTEN.
24