Elumen8 ELUM094 User manual

Order codes:
ELUM094 - 100W 3200K WW Version
ELUM095 - 100W 6000K CW Version
ELUM096 - 150W 3200K WW Version
ELUM097 - 150W 6000K CW Version
PF LED Prole
User Manual

www.prolight.co.uk PF LED Prole User Manual
2
Safety adviceSafety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Twoyearsfromdateofpurchase.

www.prolight.co.uk PF LED Prole User Manual
3
Product overview & technical specications
ThePFLEDProleisloadedwitha100W(150W)cool(warm)whiteLED,producinganoutputsimilartoa650W
(1000W)lamp.Controloftheunitisfacilitatedviaa3buttonmenuandLCDdisplay,whilstthebeamanglecan
bemanuallyadjustedbetween25°and37°.Eightdimmercurvesareincludedformaximumexibility.Thewhole
xtureisenclosedinarobustchassisfeaturingfourframingshutters,goboslotwithholderandissuppliedwith
lterframe.
•1x100WwarmwhiteCOBLED(3200K)-ELUM094
•1x100WcoolwhiteCOBLED(6000K)-ELUM095
•1x150WwarmwhiteCOBLED(3200K)-ELUM096
•1x150WcoolwhiteCOBLED(6000K)-ELUM097
•Manuallyadjustablebeamangle:25°-37°
•CRI>95
•Glasscondenseropticsystemwithzoomandfocusadjustment
•1.6kHzrefreshrate
•Beamframingshutters
•Goboslot(Gobosize:70mm)
•DMXchannels:1or2selectable
•0-100%dimming
•4dimmingcurvesinbothLEDandhalogenproles:
Linear,squarelaw,inversesquarelawandS-curve
•3pushbuttonmenuwithLCDdisplay
•PowerCONinput/output
•5-PinXLRinput/output
•Temperaturecontrolledfancooling
•Handleonrearpanel
•Filterframeincluded
•Suppliedwithgoboholder
PF LED Prole
Specications PF LED Prole
Powerconsumption 120W-100WVersion
Powerconsumption 170W-150WVersion
Powersupply 100~240V,50/60Hz
Dimensions 320x262x590mm
Weight 9.6kg
Ordercode ELUM094-100WWWVersion
Ordercode ELUM095-100WCWVersion
Ordercode ELUM096-150WWWVersion
Ordercode ELUM097-150WCWVersion
0m 1m 2m 3m 4m 5m
37°
25°
14760
9800
3700
2450
1640
1090
925
613
592
392
25° - Lux
37° - Lux
100W WW
15200
9000
3800
2250
1690
1000
950
563
608
360
25° - Lux
37° - Lux
100W CW
21000
13720
5250
3430
2330
1520
1310
856
840
548
25° - Lux
37° - Lux
150W WW
21200
12600
5300
3150
2360
1400
1130
788
848
504
25° - Lux
37° - Lux
150W CW
590mm
320mm

www.prolight.co.uk PF LED Prole User Manual
4
DMX channel mode:
OperatinginDMXcontrolmodegivestheuserthegreatestexibilitywhenitcomestocustomising
orcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthextureandeach
xtureindependently.
Toaccessthe1channelDMXmode,pressthe“MENU”buttonontherearoftheunittoshow
“DMX-1CH”ontheLCDdisplay.Thextureisnowin1Channelmode.Nowusethe“UP”and“DOWN”
buttonstosetthedesiredDMXaddressforthe1Channelmode.
Toaccessthe2channelDMXmode,pressthe“MENU”buttonontherearoftheunittoshow
“DMX-2CH”ontheLCDdisplay.Thextureisnowin2Channelmode.Nowusethe“UP”and“DOWN”
buttonstosetthedesiredDMXaddressforthe2Channelmode.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Technical specications
Operating instructions
01-Earthpoint
02-LCDdisplay
03-On/Offswitch
04-Functionbuttons
05-5-PinDMXinput
06-5-PinDMXoutput
07-PowerCONinput
08-PowerCONoutput
09-FuseT3.15A250V
Inthebox:1 x xture,
1 x 13A powerCON
mains cable &
1 x user manual
OFF
DMX INPUT POWER INPUT
POWER OUTPUT
100-240V~50/60Hz
DMX OUTPUT
ON
MENU UP DOWN
www.prolight.co.uk
PF Prole
FUSE: T3.15A 250V (T6.3A 125V)
0806 04
05 070103 09
02

www.prolight.co.uk PF LED Prole User Manual
5
Manual dimming mode:
Toaccessthesoundactivemode,pressthe“MENU”buttonontherearoftheunittoshow“WhiteSet”
ontheLCDdisplay.Theunitisnowinmanualdimmingmode.Nowusethe“UP”and“DOWN”buttonsto
setthebrightnessfrom“0” - “255”(0 = LED off, 255 = LED at full brightness).
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Dimming curves
Toaccesstheunitsdimmercurves,pressthe“MENU”buttonontherearoftheunittoshow
“Led Linear”ontheLCDdisplay.Nowusethe“UP”and“DOWN”buttonstosetthedimming
curverequired.
“Led Linear”-LEDLineardimmingcurve
“Led Square”-LEDSquaredimmingcurve
“Led InvSquar”-LEDInverseSquaredimmingcurve
“Led S-Curve”-LEDS-Curvedimmingcurve
“Halgen Linear”-HalogenLineardimmingcurve
“Halgen Square”-HalogenSquaredimmingcurve
“Halgen InvSquar”-HalogenInverseSquaredimmingcurve
“Halgen S-Curve”-HalogenS-Curvedimmingcurve
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Channel Value Function
1 000-255 Masterdimmer(0-100%)
2000-014 DimmingCurves(setviaunit)
015-044 LinearHalogendimmingcurve
045-074 SquareHalogendimmingcurve
075-104 InverseSquareHalogendimmingcurve
105-134 S-curveHalogendimmingcurve
135-164 LinearLEDdimmingcurve
165-194 SquareLEDdimmingcurve
195-224 InverseSquareLEDdimmingcurve
225-255 S-curveLEDdimmingcurve
2 channel mode:
Channel Value Function
1 000-255 Masterdimmer
(0-100%)
1 channel mode:
Pleasenote:Dimmingcurvesfor
1channelmodecanbesetvia
internalmenu.

www.prolight.co.uk PF LED Prole User Manual
6
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard5-pinXLRconnectorfordatainput/output,
seeimagebelow.
Note: DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL185 – 2m
CABL187 – 5m
CABL188 – 10m

www.prolight.co.uk PF LED Prole User Manual
7
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.Itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk PF LED Prole User Manual
8
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposed
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.