Elumen8 Evora 1000 BSW User manual

Order codes: ELUM024
Evora 1000 BSW
User Manual

www.prolight.co.uk Evora 1000 BSW User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Twoyearsfromdateofpurchase.

www.prolight.co.uk Evora 1000 BSW User Manual
3
Product overview & technical specications
TheEvora1000BSWisa3-in-1hybridmovingheadwith
supersmooth3phasemotors.Boastinganimmensely
bright180WLED,itsoutputisampleformostlargevenues
andevents.Withtheabilitytoswitchbetweenabeam,spot
andwashtheEvora1000BSWoffersahugepotentialof
creativityforprojectingpatternsontowallsorgenerating
stunningmid-aireffects.Usedasabeameffect(4.5°),the
unitemitssharpbeamsoflightwhilstasaspot(20°)the
xtureiscapableofstunningprojections.Whenoperatedin
thewashmode(45°)theunitproducessoft-edgedwashes.
•1x180WwhiteLED
•Beamangle:4.5°(Beam)20°(Spot)45°(Wash)
•4.5°-5,220Lux@10m,
20°-720Lux@10m,
45°-163Lux@10m
•3.6kHzrefreshrate
•Motorisedfocus
•8facetcircularrotatingindexableprism
plus6facetlinearrotatingindexableprism
•Frostlter
•Gobowheel1:9rotating,indexable,
replaceablegobos+open
•Gobowheel2:15staticgobos+open
•Colourwheel:9colours+3200K+open
•DMXchannels:16
•RDM(RemoteDeviceManagement)
•Auto,soundactiveandmaster/slavemodes
•Pan/tiltautocorrection
•16-Bitpan/tiltpositioning
•Pan:540°or630°selectable,Tilt:270°
•0-100%dimmingandvariablestrobe
•Suppliedwithquickreleaseomegaclamps
•6pushbuttonmenuwith1.8”LCDdisplay
•PowerCONinput/output
•3-PinXLRinput/output
•5-PinXLRinput/output
•Fancooled
Evora 1000 BSW
Specications Evora 1000 BSW
Powerconsumption 290W
Fuse T4A250V
Powersupply 100~240V,50/60Hz
Dimensions 590x390x290mm
Weight 19.4kg
Ordercode ELUM024
0m 10m 15m 20m
45° - Lux 163
5m
651 72.4 40.7
20° 45°4.5°
4.5°- Lux
20° - Lux
5220
720
20900
2880
2320
320
1310
180
590mm
390mm 290mm

www.prolight.co.uk Evora 1000 BSW User Manual
4
Technical specications
01-Earthpoint
02-LCDdisplay
03-Functionbuttons
04-3-PinDMXinput
05-3-PinDMXoutput
06-5-PinDMXinput
07-5-PinDMXoutput
08-PowerCONinput
09-PowerCONoutput
10-FuseT4A250V
11-Fans
Inthebox:1 x xture,
2 x omega clamps,
1 x power cable
& 1 x user manual
DISPLAY BACKUP
MENU UP
LEFT ENTER RIGHT
DOWN
Evora 1000 BSW
POWER INPUT:
100-240V~50/60Hz
FUSE: T3A 250V
3-PIN DMX INPUT
5-PIN DMX INPUT
3-PIN DMX OUTPUT
5-PIN DMX OUTPUT
100-240V~50/60Hz
POWER OUTPUT:
POWER CONSUMPTION: 290W
11
06
04
10
02 03 12 01 09 07
08 05
11

www.prolight.co.uk Evora 1000 BSW User Manual
5
Rotating Gobo Replacement:
Thextureissuppliedwith9rotating,replaceablegobos.Seebelowforinstallationinstructions.
1)Disconnectandisolatefrompowerthenplacethe
xtureonaatsurfaceandunscrewtheheadshell.
2)Removetheheadshellincludingthesafetywire
xedtothemetalheadplate.
3)Carefullyremoveoneofthegobotraysby
liftingslightlyandpullingtowardsyoureleasingthe
trayfromthespringclip.
4)Nowyoucanremovethecirclip,followedbythe
gobofromthegobotray.Replacethegoboandt
thecirclipbackintothetray.
5)Placethegobotraybackinto
thegobowheelbyslidingitback
underthespringclipandpushing
itdownintothewheel.
6)Fastenthesafetywirefromthe
shellbackontothemetalhead
plate.
7)Tightenthescrewsuntilthe
headshellissecure.
Rotating Gobo Replacement

www.prolight.co.uk Evora 1000 BSW User Manual
6
Operating instructions
Control Panel Menu:
TheLCDcontrolpanelsituatedonthefrontofthextureallowstheusertoaccessthemenusystemto
adjustthexturessettings.
Whentheunithasbeenpoweredonitwillshow“Software Update Please Wait...”followedby“Motor
Reset Please Wait...” and“eLumen8 Evora 1000 BSW”.Thexturewillthenreturntoitshomescreen.
Pressingthe“MENU”buttononcewilltaketheusertothexturesmainmenu.Usingthe“UP”and
“DOWN”buttonsyoucanthennavigatebetweenthedifferentoptionsinthemainmenu.Pressingthe
“ENTER”buttonononeoftheseoptionsallowsyoutoaccessthesubmenuwhereyoucanusethe
“LEFT”and“RIGHT”buttonstoselectoption/valuerequired.Oncetheoption/valuehasbeenselected
pressthe“ENTER”buttononcemoretoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressandholdthe“MENU”button.
TheLCDcontrolpanelcanbeusedviatheinternalbattery.Toaccessthispressandholdthe
“DISPLAY BACKUP”buttonfor5secondsuntilthextureshomescreenisdisplayed.TheLCD
displaywillautomaticallyshutoffafter20secondsofinactivity.
Error Codes:
Whentheunitispoweredontheunitwillautomaticallyperformamotorreset.Ifthereisaproblemwith
oneormoreofthemotorsthedisplaywillash5timesanddisplay“pan/tilt error”ontheLCDcontrol
panel.Pleasepowertheunitoffandontoresetthemotorsagain.
Offset Menu:
Toaccesstheunitsoffsetmenu
pressthe“MENU”buttononce
todisplay“DMX Address”onthe
LCDdisplay.Pressandholdthe
“ENTER” buttonuntiltheoffset
menuisdisplayed.
Offset Menu Options/Values
(Default Settings in BOLD)
Description
PanOffset -128-127(000) PanOffset
TiltOffset -128-127(000) TiltOffset
ColorOffset -128-127(000) ColorOffset
Gobo1Offset -128-127(000) GoboWheel1Offset
RGobo1Offset -128-127(000) GoboWheel1RotationOffset
Gobo2Offset -128-127(000) GoboWheel2Offset
PrismOffset 000-255(000) PrismOffset
RPrismOffset -128-127(000) PrismRotationOffset
FocusOffset 000-255(000) FocusOffset
ZoomOffset 000-255(000) ZoomOffset
Evora 1000 BSW
MENU UP
LEFT ENTER RIGHT
DOWN
DISPLAY BACKUP

www.prolight.co.uk Evora 1000 BSW User Manual
7
Operating instructions
Main Menu Sub Menu Options/Values (Default Settings in BOLD) Description
DMXAddress 001-512 DMXAddressSetting
ChannelMode 16Chan(16channelmode) DMXChannelSetting
ShowMode
Show 1
Show2
Show3
Show4
ShowModes
SplitColor No (AUTO def.)
Yes (PRO def.) SplitColourSetting
SlaveMode Slave 1 (PRO & AUTO def.)
Slave2 SlaveMode
DMXFail
Blackout
Auto (AUTO def.)
Hold (PRO def.)
DMXFailSetting
SoundState On (AUTO def.)
Off (PRO def.) SoundSetting
SoundSense 000-100(090) (PRO & AUTO def.) SoundSensitivitySetting
PanInverse No (PRO & AUTO def.)
Yes PanInverseSetting
TiltInverse No (PRO & AUTO def.)
Yes TiltInverseSetting
BackLight On (AUTO def.)
Off (PRO def.) BackLightSetting
FocusAdjust 000-255(016) GoboWheel1FocusSetting
Focus2Adjust 000-255(061) GoboWheel2FocusSetting
FunctionDelay
NoDelay
1SDelay
2SDelay
3S Delay (PRO & AUTO def.)
FunctionDelaySetting
DimmerCalibr. 050-100 DimmerCalibration
AutoTest Testing AutoTest
Temp. –––C FixtureTemperature
FixtureTime –––h FixtureRunTime
FirmwareVer. V–.––– SoftwareVersion
Defaults No
Yes
PROdef.
AUTOdef. DefaultSettings
Reset No
Yes MotorReset

www.prolight.co.uk Evora 1000 BSW User Manual
8
Operating instructions
16 channel mode:
Channel Value Function
CH1 000-255 Panadjustment0-540°
CH2 000-255 Panneadjustment
CH3 000-255 Tiltadjustment0-270°
CH4 000-255 Tiltneadjustment
CH5 000-255 Pan/tiltspeed
CH6 000-255 Masterdimmer(0-100%)
CH7
000-007 LEDoff
008-015 LEDon
016-131 Strobe(slow-fast)
132-139 LEDon
140-181 Stroberampup(slow-fast)
182-189 LEDon
190-231 Stroberampdown(slow-fast)
232-239 LEDon
240-247 Randomstrobe(slow-fast)
248-255 LEDon
CH8(when
splitcolour
isdisabled
inthemenu-
seepage6)
000-008 Open(white)
009-020 Red
021-032 Orange
033-044 Yellow
045-056 Green
057-068 Cyan
069-080 Blue
081-092 Purple
093-104 HotPink
105-116 Amber
117-127 3200K(warmwhite)
128-189 ColourscrollCW(fast-slow)
190-193 Colourscrollstop
194-255 ColourscrollCCW(slow-fast)
Channel Value Function
CH8(when
splitcolour
isenabledin
themenu-
seepage6)
000-008 Open(white)
009-014 Splitcolour(Open/Red)
015-020 Red
021-026 Splitcolour(Red/Orange)
027-032 Orange
033-038 Splitcolour(Orange/Yellow)
039-044 Yellow
045-050 Splitcolour(Yellow/Green)
051-056 Green
057-062 Splitcolour(Green/Cyan)
063-068 Cyan
069-074 Splitcolour(Cyan/Blue)
075-080 Blue
081-086 Splitcolour(Blue/Purple)
087-092 Purple
093-098 Splitcolour(Purple/HotPink)
099-104 HotPink
105-110 Splitcolour(HotPink/Amber)
111-116 Amber
117-122 Splitcolour(Amber/3200K)
123-127 3200K(warmwhite)
128-189 ColourscrollCW(fast-slow)
190-193 Colourscrollstop
194-255 ColourscrollCCW(slow-fast)

www.prolight.co.uk Evora 1000 BSW User Manual
9
Operating instructions
Channel Value Function
CH9
000-003 Open
004-007 Rotatinggobo1
008-011 Rotatinggobo2
012-015 Rotatinggobo3
016-019 Rotatinggobo4
020-023 Rotatinggobo5
024-027 Rotatinggobo6
028-031 Rotatinggobo7
032-035 Rotatinggobo8
036-039 Rotatinggobo9
040-049 Gobo1shake(slow-fast)
050-059 Gobo2shake(slow-fast)
060-069 Gobo3shake(slow-fast)
070-079 Gobo4shake(slow-fast)
080-089 Gobo5shake(slow-fast)
090-099 Gobo6shake(slow-fast)
100-109 Gobo7shake(slow-fast)
110-119 Gobo8shake(slow-fast)
120-129 Gobo9shake(slow-fast)
130-190 GobowheelscrollCW
(fast-slow)
191-194 Goboscrollstop
195-255 GobowheelscrollCCW
(slow-fast)
CH10
000-127 Goborotationindex
128-189 GoborotationCW(fast-slow)
190-193 Rotationstop
194-255 GoborotationCCW(slow-fast)
16 channel mode cont.:
Channel Value Function
CH11
000-003 Open
004-007 Staticgobo1
008-011 Staticgobo2
012-015 Staticgobo3
016-019 Staticgobo4
020-023 Staticgobo5
024-027 Staticgobo6
028-031 Staticgobo7
032-035 Staticgobo8
036-039 Staticgobo9
040-043 Staticgobo10
044-047 Staticgobo11
048-051 Staticgobo12
052-055 Staticgobo13
06+-059 Staticgobo14
060-063 Staticgobo15
064-073 Gobo1shake(slow-fast)
074-083 Gobo2shake(slow-fast)
084-093 Gobo3shake(slow-fast)
094-103 Gobo4shake(slow-fast)
104-113 Gobo5shake(slow-fast)
114-123 Gobo6shake(slow-fast)
124-133 Gobo7shake(slow-fast)
134-143 Gobo8shake(slow-fast)
144-153 Gobo9shake(slow-fast)
154-163 Gobo10shake(slow-fast)
164-173 Gobo11shake(slow-fast)
174-183 Gobo12shake(slow-fast)
184-193 Gobo13shake(slow-fast)
194-203 Gobo14shake(slow-fast)
204-211 Gobo15shake(slow-fast)
212-232 GobowheelscrollCW
(fast-slow)
233-234 Goboscrollstop
235-255 GobowheelscrollCCW
(slow-fast)
CH12
000-006 Open
007-088 6facetprism
089-172 8facetprism
173-255 Frostlter

www.prolight.co.uk Evora 1000 BSW User Manual
10
Operating instructions
Static gobos:
Open Gobo1 Gobo2 Gobo3
Gobo4 Gobo5 Gobo6 Gobo7
Gobo8 Gobo9 Gobo10 Gobo11
Gobo12 Gobo13 Gobo14 Gobo15
Channel Value Function
CH13
000-127 Prismindexing
128-189 PrismrotationCCW(fast-slow)
190-193 Prismrotationstop
194-255 PrismrotationCW(slow-fast)
CH14 000-255 Zoom
CH15 000-255 Focus
CH16
000-069 Disableall
070-079 Enableblackout
whilstpan/tilt
080-089 Disableblackout
whilstpan/tilt
090-099 Enableblackout
whilstcolourchanging
100-109 Disableblackout
whilstcolourchanging
110-119 Enableblackout
whilstgobochanging
120-129 Disableblackout
whilstgobochanging
130-199 Nofunction
200-209 Resetmotors
210-249 Nofunction
250-255 Soundactive(CH6andCH7
mustbeat255)
16 channel mode cont.:
Open Gobo1 Gobo2 Gobo3 Gobo4
Gobo5 Gobo6 Gobo7 Gobo8 Gobo9
Rotating gobos:
Gobosize:15mmØ
Imagesize:9mmØ

www.prolight.co.uk Evora 1000 BSW User Manual
11
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Note: DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.prolight.co.uk Evora 1000 BSW User Manual
12
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.Itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk Evora 1000 BSW User Manual
13
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposed
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

www.prolight.co.uk Evora 1000 BSW User Manual
14

www.prolight.co.uk Evora 1000 BSW User Manual
15

www.prolight.co.uk Evora 1000 BSW User Manual
16