emaux AFS40 User manual

V / Hz esp: See pump nameplate. Liquid temperature: 4 ~ 50
Storage temperature: -10 ~ Relativa Air Humidity: 95 Max.
+50 .
AFS SERIES PUMPS
Installation diagram
When installing and using this electrical equipment, basic safety
precautions should always be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
1) READ AND FOLLOW ALL
INSTRUCTIONS
2 WARNING) To reduce the risk of injury.
do not permit children to use this product
unless they are closely supervised at all
times.
3.WARNING Risk of Electrical Shock.
Connected only to grounding type rece-
ptacle protected by a ground fault circuit
interrupter(GFCI). Contact a qualified
electrician if you cannot verify that the
receptacle is protected by GFCI.
4 CAUTION Do not bury cord. Locate )
cord to minimize abuse from lawnmowers,
hedge trimmers, and other equipment.
5 CAUTION ) In case the running
parts will injure people, don't make
the electric pump running before then
pipeline have been connected.
6 WARNING) To reduce the risk of
electrical shock, replace damaged
cord immediately.
7 WARNING) To reduce the risk of
electrical shock, do not use extension
cord to connect unit electric supply;
provide a properly located outlet.
8 CAUTION ) Jetpump for jetted bathtubs,
spapools, swimmingpools, massage
stations, cleaning system.
9)Do not install within an outer encl-
osure or beneath the skirt of a hot tub
unless so marked.
10) This appliance is not intended for use
by young children or infirm persons unless
they have been adequately supervised by
a responsible person to ensure that they
can use the appliance safely.
11)Young children should be supervi-
sed to ensure that they do not play with
the appliance.
12 SAVE THESE INSTRUCTIONS)
SWIMMING TRAINING PUMP
INSTRUCTION MANUAL
1) General
These instructions are for correct installation, and optimum performance of the Bath
pumps, so they should be read carefully. These are single-stage centrifugal pumps
designed to operate with compact hydromassage equipment, They are equipped with
a total-emptying system to prevent the discharge of residual liquid in each stopping.
These units are designed to operate with clean water at a maximum water temperature
of 50°C. Built of top quality materials, they are subjected to strict hydraulic and electrical
controls and are carefully verified. Correct installation is ensured by following these
instructions and those of the wiring diagram; otherwise, over loads may be produced in
the motor. We decline responsibility for any damage caused by not following these
instructions.
180
280
430
245
215
E
77
319
163
95
E
Model Qmax
3
(m / h)
Hmax
(m)
90 17.5
AFS40 78 13
E
3
G2 /
4
or
4FBT
Power
P1 (kW)
4.0
3.0
1-44-4
EM PU16 0227 62
AFS55
Pump parts for AFS
Key No.
Part No.
Description
Qty
1
89023501
Union
2
2
89023502
Screw with Nut & Washer
6
3
01112094
Pump Body
1
4
02010251
O-Ring for Flange
1
5
89023503
Nut for Impeller
1
6
01271049
Impeller AFS40
1
6
01271050
Impeller AFS55
1
7
04015054
Mechanical Seal
1
8
89023504
Screw
4
9
01112095
Pump Flange
1
10
89023505
Screw
2
11
01112096
Base
1
12
01031040
Wire Box
1
13
02010265
Box Slinger
1
14
01031041
Fan
1
15
01031042
Fan cover
1

Performance curves
2.lnstallation
3.Pipe Assembly
4.Electrical connection
EN60335-2-41
5.Controls Prior to Initial Start-up
6.Start-up
7.Maintenance and clean
Our pumps for hydromassage facilities do not require any special maintenance or programming.
If the pump will be idle for a long period of time, it is recommended to disassemble, clean and store
it in a dry, well-ventilated place. If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person to a hazard.
Pump can be automotive empty water after correct installation.
When the pump needs to clean (1) filling with water up to level position of bathtub`s nozzle, (2) operating
2-3mimute,(3) exhausting water of bathtub after engine stop.
- ?Is the proper voltage applied to the pump
- ?Is there an extension cord being used
- Is the air switch hose connected to the pump ?
- Is the air switch hose connected to the actuator
button on the tub deck ?
- Jets should be pointed away from the suction
inlet so air is not forced into pump suction
- ?Is the in-tub suction inlet blocked or covered
- ?Is there any debris in the pump housing
- ?Is there a leak in the piping or the pump
- incoming power to the pump ?
- Is circuit breaker on ?
- Is GFCI operating properly ?
- Is the air switch plugged in ?
AIR SWITCH
DISCONNECTED
NO POWER
TO PUMP
PUMP DOES
NO TURN
BLOCKAGE OR
LEAK
LOW VOLTAGE
PUMP NOT
PUMPING
PROPERLY
SYMPTOM POSSIBLE CAUSE CHECK
0 80 160 240 320 400 480
.S.GPMU
0
2
4
6
8
10
12
14
16
18
0 300 600 900 1200
18 36 54 72
0 3
m/h
l/min
H
(m)
IMP.GPM
0
3
H
(psi)
6
9
12
1500
90
0 80 160 240 320 400
15
18
21
24
10
20
30
40
50
60
H
(ft)
AFS55
AFS40
2900r/min
Head
Flow
3-42-4
8.Trouble Shooting Guide