emaux SB & SR Series User manual

USER MANUAL
SB & SR Series
Centrifugal Pump
Installation and Operation Manual
Model: SB & SR Series
SAA
gep rüf te
Sich erheit SASO
EMPU21061901

SB & SR SERIES
PROVEN LONG-TERM DURABILITY
TABLE OF
CONTENT
PAGE
2
.... WARNINGS AND SAFETY INSTRUCTIONS
4
4
5
10
11
11
12
13
....
....
....
....
....
....
....
....
9. TROUBLE SHOOTING
6
....
P1 CONTENT
1. SB AND SR SERIES CENTRIFUGAL PUMP OVERVIEW
2. PRODUCT INFORMATION (SB SERIES)
3. PRODUCT INFORMATION (SR SERIES)
4. IMPORTANT SAFETY INSTRUCTIONS
5. INSTALLATION
5.1 PIPING
7
....
5.2 ELECTRICAL WIRING
5.3 ELECTRICAL WIRING– 3 PHASE
6. START UP
7. ROUTINE MAINTENANCE
8. WINTERIZING
10. REPLACEMENT PARTS
10.1 SB SERIES
10.2 SR SERIES
11. TERMS OF THE WARRANTY
16
....

WARNINGS AND SAFETY INSTRUCTIONS
GENERAL WARNING
This instruction contain general caution information for use in Pool and SPA pump installation application.
Specified Pump model function should be refer to particular manual. Components such as the filtration system,
pumps and heater must be positioned so as to prevent their being used as means of access to the pool by young
children.
This appliance should be installed by qualified electrical personnel in
accordance with National Electrical Code and all applicable local codes
and ordinances. Hazardous voltage can shock, burn, and cause death or
serious property damage. DO NOT use an extension cord to connect unit
to electric supply to reduce the risk of electric shock.
RISK OF ELECTRICAL SHOCK
1. The pump should be permanently connected to an individual circuit breaker.
2. Pump must be connected to a residual current device (RCD) having a rated residual operating current not
exceeding 30 mA or receptacle with ground fault circuit interrupt (GCFI).
3. Electrical grounding must be connected before connecting to electrical power. Failure to ground all electrical
equipment can cause serious or fatal electrical shock hazard.
4. Bonding: Use at least #8 AWG (#6 AWG for Canada) a solid copper conductor, run a continuous wire from
external bonding lug (if available) to the pressure wire connector provided on the electrical equipment and
to all metal parts of swimming pool, spa, or hot tub, and metal piping (except gas piping), and conduit within
1.5 m (5 ft) of inside walls of swimming pool, spa, or hot tub.
5. Never open the inside of the drive motor enclosure. There is a capacitor bank that holds a mains supply
voltage charge even when there is no power to the unit. The voltage should be referred to the individual
pump operation voltage.
6. The pump is capable of high flow rates; use caution when installing and programming to limit pumps
performance only.
7. Switch OFF pump power before servicing and disconnecting the main circuit to the pump.
8. Never change the filter control valve position while the pump is running.
COMPRESS AIR HAZARDOUS
This system enclosed pre-filter / filter and become pressurized.
Pressurized air can cause the Lid to separate which can result in serious
injury or death.
Pool and spa circulation systems operate under high pressure. When any part of the circulating system (i.e. lock
ring, pump, filter, valves, etc.) is serviced, air can enter the system and become pressurized. Filter tank Lid and
pre-filter cover must be properly secured to prevent violent separation. Place pre-filter / filter air relief valve in
the open position and wait for all pressure in the system to be relieved before remove the lib to access the
basket for cleaning.
HYPERTHERMIA
SPA water temperature excess 38°C (104°F) may be injurious to health.
Measure water temperature before entering SPA.
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the
normal body temperature of 98.6 °F (37 °C). The symptoms of hyperthermia include drowsiness, lethargy, and
an increase in the internal temperature of the body.
WARNINGS AND SAFETY INSTRUCTIONS P2

SUCTION ENTRAPMENT HAZARD
This pump produces high levels of suction and creates a strong vacuum at
the main drain at the bottom of your pool and spa. This suction is so strong
that it can trap adults or children under water if they come in close proximity
to a pool or spa drain or a loose or broken drain cover or grate.
The Virginia Graeme Baker (VGB) Pool and Spa Safety Act creates new
requirements for owners and operators of commercial swimming Pools and
spas.
Commercial pools or spas constructed on or after December 19, 2008, shall utilize:
1. A multiple main drain system without isolation capability with suction outlet covers that meet ASME/ANSI
A112.19.8a Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, and Hot Tubs and either:
1.1 A safety vacuum release system (SVRS) meeting ASME/ANSI A112.19.17 Manufactured Safety Vacuum
Release systems (SVRS)
For Residential and Commercial Swimming Pool, Spa, Hot Tub, and Wading Pool Suction Systems and/or
ASTM F2387 Standard
Specification for Manufactured Safety Vacuum Release Systems (SVRS) for Swimming pools, Spas and Hot
Tubs or
1.2 A properly designed and tested suction-limiting vent system or
1.3 An automatic pump shut-off system.
Commercial pools and spas constructed prior to December 19, 2008, with a single submerged suction outlet shall
use a suction outlet cover that meets ASME/ANSI A112.19.8a and either:
1. A SVRS meeting ASME / ANSI A112.19.17 and/or ASTM F2387, or
2. A properly designed and tested suction-limiting vent system, or
3. An automatic pump shut-off system, or
4. Disabled submerged outlets, or
5. Suction outlets shall be reconfigured into return inlets.
There are five types of suction entrapment according to The Virginia Graeme Baker (VGB) Pool and Spa Safety Act
1. Body Entrapment a section of the torso becomes entrapped
2. Limb Entrapment an arm or leg is caught by or pulled into an open drainpipe
3. Hair Entrapment or entanglement hair is pulled into and/or wrapped around the grate of the drain cover
4. Mechanical Entrapment the bather's jewelry or clothing gets caught in the drain or the grate
5. Evisceration the victim's buttocks come into contact with the pool suction outlet and he or she is disemboweled
TO REDUCE ENTRAPMENT HAZARD RISK
Two function suctions outlets per pump must be installed to prevent entrapment. The
minimum separate of suction on the same plate must be at least point to point measurement 1
meter (3ft) apart. It is used to avoid “dual blockage” by bather.
If suction is found damage, broken, cracked, missing or not securely attached during regular
checking, shunt down the pool and replace it immediately.
A vacuum release or vent system is recommended to install for suction entrapment release.
P3 SUCTION ENTRAPMENT HAZARD

1. SB AND SR SERIES CENTRIFUGAL PUMP OVERVIEW
It is a mediumpower, low noise and easy to maintenance self-priming pump for medium residential in ground pool
installation. SB series Pre-filter with transparent Lid cover easy to observe the basket need to be clean or not.
IPX5 aluminum motor enclosure design is good for outdoor deployment and heat dissipation.
There is built in thermal protection to protect the motor when fault operation cause motor over heat.
220Vac, 50Hz or 60Hz and 380Vac electrical power is available.
2. PRODUCT INFORMATION (SB SERIES)
Model
50Hz Input
(kW)
Current
(AMP)
Noise
(dB)
Head(m)
6810 12 14 16
FlowRate(m³/h)
SB10
SB15
SB20
0.97
1.30
1.80
4.7
8.2
5.9
67
69
67
16.4
31
24
14
28
22
11
25.2
19.5
7
22
16
–
18
12
–
12
2
Code
220V/50Hz Code 220V/60Hz Code 380V/50Hz Model Connection
Size
88021305 88021605 88021405 SB10 2”/63mm 1.0hp
Horsepower Weight
(kg)
16.0
88021307
88021308
88021607
88021608
88021407
88021408
SB15
SB20
2”/63mm
2”/63mm
1.5hp
2.0hp
17.0
23.0
DIMENSIONS
SB and SR SERIES CENTRIFUGAL PUMP OVERVIEW P4
SB30 2.18 10.5 69 34 32 28.4 26 23 19.2
88021309 88021609 88021409 SB30 2”/63mm 3.0hp 24.0
Capacitance
25μF
25μF
30μF
35μF
248
413
275 717

P5 PRODUCT INFORMATION (SR Series)
3. PRODUCT INFORMATION (SR SERIES)
Model
50Hz Input
(kW)
Current
(AMP)
Noise
(dB)
Head(m)
810 12 14 16
FlowRate(m³/h)
SR10
SR15
SR20
0.97
1.30
1.80
4.7
8.2
5.9
67
69
67
17
29.2
21
14
27
18.8
10
24
14.8
20.5
11.6
–
16
2
Code
220V/50Hz Code 220V/60Hz Code 380V/50Hz Model Connection
Size
88023605 88023705 88023905 SR10 2”/63mm 1.0hp
Horsepower Weight
(kg)
14.70
88023607
88023608
88023707
88023708
88023907
88023908
SR15
SR20
2”/63mm
2”/63mm
1.5hp
2.0hp
16.30
19.70
SR30 2.18 10.5 69 32 30.5 28 25 21
88023609 88023709 88023909 SR30 2”/63mm 3.0hp 22.10
Capacitance
25μF
25μF
30μF
35μF
4
0 50 100 150 200 250 300 350 400 450 500 550
0 2 46 8 10 12 14 16 18 20 22 24 26 28 30 32 34
0
2
4
6
8
10
12
14
16
18
20 40 60 80 100 120 140
60
50
40
30
20
10
0
Q(m³/ h)
Q(LPM)
H(ft)
H m( )
U.S.g.p.m
SB10
η
%40 45 50
60
70
70
6050
SB15
SB20 SB30
PERFORMANCE CURVE

IMPORTANT SAFETY INSTRUCTIONS P6
The user guide you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must
read the instructions before beginning installation and start-up. Keep this manual for future
reference.
4. IMPORTANT SAFETY INSTRUCTIONS
DIMENSIONS
PERFORMANCE CURVE
275
144
413
557
20 40 60 80 100 120 140
U.S.g.p.m
0
2
4
6
8
10
12
14
16
18
20
H m( )
0 2 4 6 8 10 12 18 24 30 14 20 26 3216 22 28 34
0 50 100 150 200 250 300 350 400 450 500 550
Q(m³/ h)
Q(LPM)
60
50
40
30
20
10
0
H(ft)
SR10
SR15
SR20
SR30

P7 INSTALLATION
5. INSTALLATION
Correct disposal of this product
This symbol on the product, or in its packaging, indicates that this
product may not be treated as household waste. Instead, it should
be taken to the appropriate waste collection point for the recycling
of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could
otherwise be caused by the inappropriate waste handling of this
product. For more detailed information about the recycling of this
product, please contact your local council, your household waste
disposal service, or the shop where you purchased the product.
5.1 PIPING
1. A protective device is to be installed in the fixed wiring.
2. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with
the appliance. Cleaning and user maintenance shall not be made by children without supervision.
3. The appliance shall be installed in accordance with national wiring regulations means for disconnection must be
incorporated in the fixed wiring in accordance with the wiring rules. A disconnected incorporated in the fixed
wiring is to be provided.
4. The pump is to be supplied through a residual current device (RCD) or Ground Fault Circuit Interrupt (GFCI)
having a rated residual operation current not exceeding 30mA.
1. Install the pump as close to the pool as possible, preferably in a dry, well ventilated area away from direct sun
light. Protect the pump from excessive moisture.
2. Place the pump as close to the water source as possible, so that the suction pipe is short, straight and direct to
reduce the friction loss. Don't install the pump at more than 10 ft (3 meters) of geometrical height from water
level.
3. Before installing the pump, make sure that the surface is solid, elevated, rigid and vibration free.
4. Secure the pump to the base with screws or bolts to limit the vibration and the stress on the pipe or the joints.
5. Leave enough space for gate valves in suction and discharge piping, if required.
6. Ensure there is enough clearance for pre-filter basket & Lid open and motor ventilation.
7. Connect the suction and discharge pipe to the outlet and inlet of the swimming pool.
8. Make sure that floor drainage is adequate to prevent flooding.
9. Make sure that the pump and piping are accessible for servicing.

INSTALLATION P8
Note: The pump suction and discharge connections are mounded in
thread stops, DO NOT try to screw the pipe beyond these stops.
SB and SR series pump has 2 sets 2” union adaptor in internal and external
thread and universal design for metric and imperial PVC pipe connection.
5.2 ELECTRICAL WIRING
Warning: This power pump demand licensed or certified electrician or
qualified pool installer to ensure there is adequate protection between
the pump motor and mains power supply according to individual countries
safety code.
The pump has power cord with plug attached on the plug, plug it to a
power socket with circuit breaker to isolate the motor from the mains
power for over load protection. The circuit breaker rating should refer to the electrical specification of
individual pump working voltage and power.
The power has to be with a Residual Current Device (RCD) or Ground Fault Circuit Interrupt (GFCI) having a rated
residual operating current not exceeding 30mA.
If the RCD / GFCI device trips, it means there is fault on the power line or motor. Do not use
this pump. Disconnect the pump and have the problem corrected by a qualified service
representative before using. Press the reset button to reset the RDC / GFCI devices after
fixed. It will keeps the circuit shut off and will not reset if the power line problem is not
fixed.
It is recommend to test the RCD / GFCI at least once a month.
MIN 5 X SUCTION
PIPE DIAMETER
Recommended Piping
ELBOW
Veritcal lift
no more than 3m(10ft)
Pumps should be shipped with Power cord with plug for corresponding countries. If there is not power cord
attached to the pump, it is necessary to follow the local electricity power line color code to connect the power
according to the wiring for individual pump diagram.
5.3 ELECTRICAL WIRING– 3 PHASE
For pump operate at 380Vac or above, 3 phase power line is needed to drive the motor. The latest cable color
code is Brown for L1, Black for L2, Grey for L3 , Blue for Neutral and Green & Yellow for Earth.
For old code it is Red for L1, Yellow for L2, Blue for L3, Black for Neutral and Green & Yellow for Earth.

P9 INSTALLATION
DOL starting is the simplest, cheapest and most common starting method. It actually gives the lowest temperature
rise within the motor during startup of all the starting methods. But the drawback is starting current can be 3-8
time of full load current. Therefore, it is not recommend for pump power higher than 5.5KW in public low voltage
mains 400V.
The typical common 3 phase pump Run / Stop starter is Direct-On-Lone Starter that include:
1. Motor Circuit Breaker is a short circuit magnetic protection devices.
2. Control unit for Run and Stop operation and status monitoring.
3. Protection relay is an overload thermal protection device.
4. Single phase MCB for secondary protection.
DOL Starter can be applied to motor connect in Delta or WYE / Star
connection.
Factory default 3 phase motor connection is in Delta Connection
and can't be changed.
Low Voltage
Delta Connection
W2 U2 V2
U1 V1 W1
L1 L2 L3 T
1
Direct-On-Line (DOL) Starter typical wiring.
Contactor
Stop
Run
Protection
Relay
Motor Circuit
Breaker
MCB
It is a typical wiring diagram for reference only. All electrical rating of individual device has
to match with pump's current rating.
3 phase Cable
New Wire Color Code
3 phase Cable
Old Wire Color Code
L/L1
L2
L3
N
Earth
Brown
Black
Grey
Blue
Green & Yellow
L/L1
L2
L3
N
Earth
Red
Yellow
Blue
Black
Green & Yellow

START UP P10
6. START UP
1. Verify the pump shaft turn freely.
2. Check the mains voltage, current and frequency are accordingly to the name plate.
3. Never run pump dry! Running pump dry may cause damage to the mechanical seal causing
leakage and flooding. Fill the pre-filter with water before starting motor.
4. Before removing the pre-filter Lid, STOP PUMP, CLOSE GATE VALVES in suction and discharge
pipes.
5. Always STOP THE PUMP before when RELEASE ALL PRESSURE from the pump and the piping system before
proceeding.
6. Never tighten or loosen screw while the pump is in operation.
7. The suction pipe and the suction inlet in the pool must be free from obstruction.
Before start-up, the alignment of the pump should be checked. The tubing should be inspected to ensure that they
are properly fitted and tightened and that they do not exert pressure or tension on the pump's suction or discharge
connection. The pump should never be operated.
Wiring Box Diagram:
SB10, SB15,SB20, SB30, SR10, SR15, SR20. SR30 all model 220Vac 50/60Hz.
Circuit
Breaker
Ground
Capacitor Holder
Capacitor
L
N
WARNING: Tighten/untighten the pump Lid by hand only.
1. Clear all piping of construction debris and verify that the piping has passed a proper pressure test.
2. Check the filter and other equipment for proper installation, verifying all clamps and connections are properly
installed as per the manufacturer's instructions.
3. Open any shut off valves on the suction and discharge lines.
4. Open the filter pressure relief valve and release all pressure from the system.
5. If the pump is located below the water level of the pool, opening the pressure relief valve will fill the pump with
water.
6. If the pump is located above the pool water level, remove the Lid from the pre-filter and fill with water before
starting the pump.
7. Check to see that the Lid O-ring and seat areas are clean and lubricated. Debris in the sealing area can cause air
to leak into the system and make it difficult to prime the pump.
8. Close / tighten the Lid to make an airtight seal.
9. Turn on power wait for pump to prime. Pump priming time for 3m (10ft) should be at least 4.5 minutes. Priming
will depend on vertical length of suction lift and horizontal length of suction pipe. If pump does not prime within
prime time, stop the motor and determine cause.
10. If the pump does not prime within 10 minutes. Ensure all instructions to this point have been followed. Stop the
pump! Check for suction leaks and repeat steps (1) through (8).

P11 ROUTINE MAINTENANCE
7. ROUTINE MAINTENANCE
The pump mechanical seal requires no lubrication and service.
The only routine maintenance needed is the inspection and cleaning of
the pre-filter basket. Debris or trash collected in the basket will choke
off the water flow through the pump. Follow the instructions below in
order to clean the pre-filter basket:
1. Turn off the pump, close the gate valve in suction and discharge, and
release all pressure from the system before proceeding.
2. For SB pump series, turn the transparent Lid cover follow the arrow
on the Lid cover by lid ring opening key provided to release and lock.
3. Remove the pre-filter basket and cleaning. Make sure all the holes in
the basket are clear, flush the basket with water and replace it in the
trap with large opening at the pipe connection port (between rib
sprovided). If the basket is replaced back wards, the cover will not fit
on the trap body.
4. Clean and inspect the Lid's O-ring ring; reinstall on the Lid cover.
5. Clean the ring groove on the pre-filter body and replace the Lid. To
help keep the Lid from sticking, tighten it by hand only.
6. Put back the basket with opening face directly to the suction inlet as
the picture show above.
7. Fill up the filter body with water and Prime the pump.
8. WINTERIZING
If the air tempera ture drops below 0°C (35°F), the water in the system can freeze and cause damage. Freezing
damage is not warrantable.
To prevent freezing damage follow the procedures listed below:
1. Shut off electrical power for the pump at the house circuit breaker.
2. Drain the water out of the pump case by removing the two drain plugs from the case.
3. Store the plugs in the pump basket.
4. Cover the motor to protect it from severe rain, snow and ice.
5. If it is possible, store the pump in a dry location during this time.
6. Do not wrap the motor in plastic. It will cause condensation and rust on the inside of the motor.
7. Where possible, have a qualified service technician or electrician disconnect the electrical wiring at the switch
or junction box and store the pump indoors.
8. When the pump is reactivated, ensure all seals and O-rings are in operational condition. If they are not, re-
greasing or replacing may be necessary.

TROUBLE SHOOTING P12
9. TROUBLE SHOOTING
Problem description Possible causes
Motor does not start
1. Disconnect switch or circuit breaker in off position
2. Fuses blow nor thermal over load open
3. Locked motor shaft
4. Motor windings burned out
5. Defective starting switch inside single phase motor
6. Disconnected or defective wiring
7. Low voltage
Pump does not reach full speed 1. Low voltage
2. Pump connected to the wrong voltage
Motor over heats (protect or trips) 1. Low voltage
2. Motor windings connected to the wrong voltage on dual voltage model
Pump delivers no water
1. Pump is not primed
2. Closed valve in suction or discharge line
3. Leakage or air into suction system
4. Impeller clogged
Leakage of water at the shaft Shaft seal requires replacement
Low pump capacity
1. Valve in the suction or discharge line partly closed
2. Suction or discharge line partly plugged
3. Suction or discharge line too small
4. Plugged basket in skimmer or hair and lint strainer
5. Dirty filter
6. Impeller clogged
High pump pressure
1. Discharge vale or inlet fittings closed too much
2. Return lines too small
3. Dirty filters
Noisy pump and motor
1. Plugged basket in skinner or hair in lint strainer
2. Worn motor bearings
3. Valve in suction line partly closed
4. Suction line partly plugged
5. Vacuum hose plugged or too small
6. Pump not supported properly
Air bubbles at inlet fittings
1. Leakage of air into the suction line in connections or valve stem
2. Cover gasket of hair and lint strainer needs cleaning
3. Low water level in the pool
Note: If the above recommendations of this manual do not solve your particular problem(s), please contact your
local service agent for further assistance.

P13 TROUBLE SHOOTING
10. REPLACEMENT PARTS
1
2
3
4
5
6
7
8 9 10
11
12
13
14
15
16 17
18 19 20
21 22
23
24
25
26
27
28
29
20
20
29
28
31
32
30
10.1 SB SERIES
Key No. Part No. Description QTY
1
2
3
4
5
6*
7
8
9
10
11
12
13
14
14
14
14
14
14
15
16
17
18
19
20
20
01021008
01041022
02010248
01111030
89021305
89280103
89021307
02011115
03011083
89021308
89021309
02011108
01111015
01311001
01311002
01311003
01311004
01311005
01311006
E020001
02011093
01021013
03011080
02011096
89021301
89021302
Nut for lid
Transparent Lid
O-Ring for Lid
Basket
Pre-Filter Body
2.0" Union (Black/ White Colour)
Drain Plug with O-ring
Square Gasket
M6 x 30 Screw for Pump Body
Pump body for SB,SR
Screw for Impeller with O-Ring
O-Ring for Diffuser
Diffuser
Impeller SB10 (110V/60Hz) and (220V/60Hz)
Impeller SB20 (110V/60Hz) and (220V/60Hz)
Impeller SB/ SR20 (220V/50Hz) and (380V/50Hz)
Impeller SB/ SR10 (220V/50Hz) and (380V/50Hz)/ SB15 (110V/60Hz) and (220V/60Hz)
Impeller SB/ SR15 (220V/50Hz) and (380V/50Hz)/ SB30 (110V/60Hz) and (220V/60Hz)
Impeller SB30 (220V/50Hz) and (380V/50Hz)
3/4" Mechanical seal
O-Ring for Flange
Pump Flange for SB/ SR
M6×15 Hexagonal Bolt
Motor Slinger
Motor SB/ SR10 (220V/50Hz)
Motor SB/ SR15 (220V/50Hz)
1
1
1
1
1
2
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
16
1
1
1
220V/50Hz 20 110V/60Hz

REPLACEMENT PARTS P14
Key No. Part No. Description QTY
20
20
20
20
20
20
20
20
20
20
20
20
20
20
21
22
23
23
24
25
26
26
27
27
28
28
29
29
29
29
29
30
30
30
30
31
32
89021303A
89021304
89021401
89021402
89021403
89021404
89021601
89021602
89021603
89021604
89021501
89021502
89021503
89021504
89021310
01021021
01111032
01111031
89021312
89021505
01031001
01031002
01031008
01031009
01031007
01031006
04016014
04016015
04016016
04016022
04016023
04015042
04015015
04015012
04016037
02021039
04014018
Motor SB/ SR20 (220V/50Hz)
Motor SB/ SR30 (220V/50Hz)
Motor SB/ SR10 (220V/60Hz)
Motor SB/ SR15 (220V/60Hz)
Motor SB/ SR20 (220V/60Hz)
Motor SB/ SR30 (220V/60Hz)
Motor SB/ SR10 (380V/50Hz)
Motor SB/ SR15 (380V/50Hz)
Motor SB/ SR20 (380V/50Hz)
Motor SB/ SR30 (380V/50Hz)
Motor SB/ SR10 (110V/60Hz)
Motor SB/ SR15 (110V/60Hz)
Motor SB/ SR20 (110V/60Hz)
Motor SB/ SR30 (110V/60Hz)
M8*20 Bolt for motor with washer
Opening key
Base with Nut & Washer for SB10/ Sb15
Base with Nut & Washer for SB20/ Sb30
Cable Box for SB/ SR Pump 220V/50Hz; 220V/60Hz; 380V/50Hz.
Cable Box for SB/ SR Pump 110V/60Hz
Fan Cover for EPH SB/SR20 SB/SR30
Fan Cover for SB/SR10,SB/SR15 Pump
Fan Cover for SB/SR20,SB/SR30 Pump
Fan Cover for SB/SR10,SB/SR15 Pump
Cooling fan for SC SB/SR10,SB/SR15
Cooling fan for EPH SB/SR20,SB/SR30
Capacitor for SB/ SR10/ SB/ SR15 (220V/50Hz) (220V/60Hz)
Capacitor for SB/ SR20 (220V/50Hz) (220V/60Hz)
Capacitor for SB/ SR30 (220V/50Hz) (220V/60Hz)
Capacitor for SB/ SR10/ SB15 (110V/60Hz)
Capacitor for SB/ SR20/ SB30 (110V/60Hz)
Overload Switch PE77-6A/250VAC for SB/ Sr10
Overload Switch PE77-8A/250VAC for SB/ Sr15
Overload Switch PE77-10A/250VAC for SB/ Sr20
Overload Switch PE77-13A/250VAC for SB/ Sr30
Cover for Overload Switch
Insulation Fitting for Overload Switch
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Note: 6* 89280103B is 2.0 Union in Black Colour
6* 89280103W is 2.0 Union in White Colour

10.2 SR SERIES
(220V/50Hz)
(110V/60Hz)
1234
56
7
8
9 10
11 12 13
14 15
16
17
18
19
21
2
13
19 20
13 13
16
Key No. Part No. Description QTY
1*
2
3
4
5
6
7
7
7
7
7
7
8
9
10
11
12
12
13
13
13
13
13
13
13
13
13
13
13
13
13
13
89280103
89023601
89021308
89021309
02011108
01111015
01311001
01311002
01311003
01311004
01311005
01311006
E020001
02011093
01021013
03011080
02011099
02011101
89021301
89021302
89021303A
89021304
89021401
89021402
89021403
89021404
89021601
89021602
89021603
89021604
89021501
89021502
2.0" Union (Black/ White Colour)
Connecting Fitting
Pump body for SB,SR
Screw for Impeller with O-Ring
O-Ring for Diffuser
Diffuser
Impeller SR10 (110V/60Hz)/ (220V/60Hz)
Impeller SR20 (110V/60Hz)/ (220V/60Hz)
Impeller SR20 (220V/50Hz)/ (380V/50Hz)
Impeller SR10 (220V/50Hz) and (380V/50Hz)/ SR15 (110V/60Hz) and (220V/60Hz)
Impeller SR15 (220V/50Hz) and (380V/50Hz)/ SR30 (110V/60Hz) and (220V/60Hz)
Impeller SR30 (220V/50Hz) and (380V/50Hz)
3/4" Mechanical Seal
O-Ring for Flange
Pump Flange for SB,SR
M6 ×15 Hexagonal Bolt
Motor Slinger for SR10/ Sr15
Motor Slinger for SR20/ Sr30
Motor SB10 or SR10 (220V/50Hz)
Motor SB15 or SR15 (220V/50Hz)
Motor SB20 or SR20 (220V/50Hz)
Motor SB30 or SR30 (220V/50Hz)
Motor SB10 or SR10 (220V/60Hz)
Motor SB15 or SR15 (220V/60Hz)
Motor SB20 or SR20 (220V/60Hz)
Motor SB30 or SR30 (220V/60Hz)
Motor SB10 or SR10 (380V/50Hz)
Motor SB15 or SR15 (380V/50Hz)
Motor SB20 or SR20 (380V/50Hz)
Motor SB30 or SR30 (380V/50Hz)
Motor SB10 or SR10 (110V/60Hz)
Motor SB15 or SR15 (110V/60Hz)
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
16
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
P15 REPLACEMENT PARTS

TERMS OF THE WARRANTY P16
Key No. Part No. Description QTY
13
13
14
15
15
16
16
16
16
16
17
18
19
19
20
20
21
21
89021503
89021504
89021310
01111032
01111031
04016014
04016015
04016016
04016022
04016023
89021505
89021312
01031007
01031006
01031001
01031002
01031008
01031009
Motor SB20 or SR20 (110V/60Hz)
Motor SB30 or SR30 (110V/60Hz)
M8*20 Bolt for motor with washer
Base with Nut & Washer for SB/SR10 / SB/SR15
Base with Nut & Washer for SB/SR20 / SB/SR30
Capacitor for SB/SR10, SB15
Capacitor for SB/SR20 & SC/EPH200 & SPH200 Pump
Capacitor for SB/SR30 EPH300,EPH400 & SPH300 Pump
Capacitor for SR/SB10-15 & SC100-150 Pump 110V
Capacitor for SR/SB20-30 & SC200 Pump 110V
Cable Box
Cable Box for SR Pump 220V/50Hz / 220V/60Hz / 380V/50Hz.
Cooling fan for SC SB/SR10 / SB/SR15
Cooling fan for EPH SB/SR20 / SB/SR30
Fan Cover for EPH SB/SR20 / SB/SR30
Fan Cover for SB/SR10 / SB/SR15 Pump
Fan Cover for SB/SR20 / SB/SR30 Pump
Fan Cover for SB/SR10 / SB/SR15 Pump
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Note: 1* 89280103B is 2" Union in Black Colour
1* 89280103W is 2" Union in White Colour
11. TERMS OF THE WARRANTY
As original purchaser of this equipment have purchased from Emaux Water Technology Co Ltd, through
Authorized International Distributor or Dealer, warrants its products free from defects in materials and
workmanship under normal use during warranty period. The warranty period begins on the day of purchase and
extends only to the original purchaser. It is not transferable to anyone who subsequently purchases the product
from you. It excludes all expendable parts.
During the warranty period, Emaux authorized reseller will repair or replace defective parts with new parts or, at
the option of Emaux, serviceable used parts that are equivalent or superior to new parts in performance.
This Limited Warranty extends only to products purchased from Emaux authorized reseller. This Limited
Warranty does not extend to any product that has been damaged or rendered defective (a) as a result of
accident, misuse or abuse;
(b) as a result of an act of God;
(c) by operation outside the usage parameters stated herein;
(d) by the use of parts not manufactured or sold by Emaux;
(e) by modification of the product;
(f) as a result of war or terrorist attack; or
(g) as a result of service by anyone other than Emaux authorized reseller or authorized agent.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, EMAUX MAKES NO OTHER WARRANTIES EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. EMAUX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS EXPRESS LIMITED
WARRANTY.

STRIVE FOR CLEAR WATER
www.emauxgroup.com
EMAUX WATER TECHNOLOGY CO., LTD