emaux FSP350-6W User manual

1
INSTALLATION
FILTER & PUMP COMBO
Installation & Operating Instruction
FSP350-6W / FSP400-6W / FSP450-6W / FSP500-6W / FSP650-6W
EMFS18111971
* Install filtration system including pump,filter tank and multiport valve.
* The filter system should be installed as close as possibie to the swimming pool and preferably at a level
of 0.50 metres below the surface of the water in the swimming pool. Make sure there is drainage
available at the place where the filter is to be installed.
* PUMP
1) Only qualified,licensed personnel should install pump and wiring.
2) Electrical Contractors Please Note:All 220 volt 50Hz pump must be wired to the main power supply
trough an approved and correctly rated contractor.
3) Allow for gate valve in suction piping.
4) Pump suction and discharge connections have moulded in thread stops,do not try to screw pipe in
beyond these stops.
* FILTER TANK and MULTIPORT VALVE
1) Loading the sand media.Filter sand media is loaded through the top opening of the filter.
a) Loosen the plastic clamps from tank neck.
b) Cap internal pipe with plastic cap to prevent sand from entering it.
c) We recommend filling tank approximately 1/2 way with water to provide a cushion effect when the
filter sand is poured in. This helps protect the under-drain laterals from excessive shock.
d) Carefully pour in correct amount and grade of filter sand.Be sure center pipe remains centered in
opening. Sand surface should be leveled and should come to about the middle of the filter
tank.Remove plastic cap from internal pipe.
2) Assemble filter control valve to filter tank.
a) Insert filter control valve(with O'ring in place)into the tank neck,taking care that the center pipe slips
into the hole in the bottom of the valve.
b) Place two plastic clamps around valve flange and tank neck and tighten just enough so that the
valve mayBe rotated on tank for final positioning.
c) Carefully screw pressure gauge(with O'ring in place)into tapped hole in valve body.Do not over-
tighten.
d)Connect pump to control valve opening marked PUMP with hose.After connections are made,
tighten clamps with screwdrive,tapping around clamp with screwdrive handle to help seat valve
flange clamp.
3) Make return to pool pipe connection to control valve opening marked RETURN and complete other
necessary plumbing connections,suction lines to pump,waste,etc.
4) To prevent water leakage,be sure all pipe connections are tight.

15
P350
2 1 3
6
8
9
10
12
13
14
16
17
18
19
5
4
6
7
11
INSTALL/START-UP OF FILTRATION
REPLACEMENT PARTS OF FILTER
2
Item
Part No.
Description
Qty
1
88280105
1.5"Top Mount Valve
1
2
89280101
1.5" union with sight glass,O-Ring
1
3
89280102
1.5" Union Set With O-Ring
1
4
06021013
Plastic Pressure Gauge With O-Ring ( 40psi)
1
01111048
Connector for pressure gauge
1
5
89030204
Hose adaptor with O-Ring
1
6
02011026
Sleeve for Hose
2
7
89031501
FSP350-6W Plastic Hose with Nut
1
89031601
FSP400-6W Plastic Hose with Nut
1
89031701
FSP450-6W Plastic Hose with Nut
1
89031801
FSP500-6W Plastic Hose with Nut
1
89031901
FSP650-6W Plastic Hose with Nut
1
8
01013049
Hose adaptor with nut
1
9
02011104
O-Ring for pump
1
10
08030006
SS020(220V/50Hz)
1
08030007
SS033(220V/50Hz)
1
08030008
SS050(220V/50Hz)
1
08030009
SS075(220V/50Hz)
1
08030010
SS100(220V/50Hz)
1
08030011
SS120(220V/50Hz)
1
11
89032001
Pump Assembly Screw
2
12
89010119
M6*50 Screws With Nut
2
01271010
Clamp Lock
2
13
02011134
O-Ring for Filter Neck
1
14
01331005
P350 Filter Tank
1
01331006
P400 Filter tank
1
01331007
P450 Filter tank
1
01331008
P500 Filter tank
1
01331010
P650 Filter tank
1
15
89011602
P350 Lateral Assembly with Center Pipe
1
16
89011603
P400 Lateral Assembly with Center Pipe
1
89011604
P450 Lateral Assembly with Center Pipe
1
89011605
P500 Lateral Assembly with Center Pipe
1
89011606
P650 Lateral Assembly with Center Pipe
1
17
01172007
P400-P450 Laterals ( 115mm)
8
01172008
P500-P650 Laterals ( 126mm)
8
18
89011601
Water Drain Set
1
19
01111056
FSP350 Combo Base
1
01111053
FSP400-FSP650 Combo base
1
1 Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2 Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always
depress handle before turning.)
3 Prime and start pump. Never tun pump dry! Running pump dry may damage seals,causing leakage and flooding!
Fill pump with water before starting motor. (be sure all suction and return lines are open), allowing the filter tank to
fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial back-
washing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4 Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2
to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the
normal filter mode, filtering dirt particles from the pool water.
5 Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
connections, bolts, nuts, as required.
6 Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation
in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is 1.5 bar, higher
than the initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under filter and control
valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
)
)
)
)
)
)

SS PUMP REPLACEMENT PARTS
PRIMING PUMP
3
Release all air from filter and piping system.
In a flooded suction system (water source higher than pump), pump will prime itself when suction and
discharge valves are opened.
If pump is not in a flooded suction system, unscrew and remove trap cover; fill trap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace trap cover on trap; turn clockwise to tighten cover.
NOTICE: Tighten trap cover by hand only .Pump should prime now. Priming time will depend on vertical
length of suction lift and horizontal length of suction piping.

4
WARNING
VALVE REPLACEMENT PARTS
By-passes filter for circulating water to pool
Used after backwash to flush dirt from valve
Cleaning Filter by reversing the flow
By-passes filter, used for vacuuming to waste or lowering water level
CLOSED Shuts off all flow to filter or pool
RECIRCULATE
WASTE
RINSE
BACKWASH
FILTER
Valve Position
Normal Filtration and Vacuuming
Function
THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING SYSTEM
(e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE SYSTEM AND BECOME
PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO BE BLOWN OFF WHICH CAN
RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE.
TURN PUMP OFF BEFORE CHANGING VALVE POSITION.
TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM.CLEAN PUMP
STRAINER AND SKIMMER BASKETS REGULARLY.
DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.
!
!
!
!
18
17
16
15
14
12
11
10
9
8
7
6
5
4
3
2
1
13
21
14
15
16
19
18
20
23
22
Item
Part No.
Description
Qty
1
01013003
Handle (Big)
1
2
03018008
Pin for Handle
1
3
01181001
Washer for Handle
1
4
89280107
M6 x 30 Screw with Nut for Standard Lid
6
5
01013004
1.5" Top/Side Mount Valve Standard Lid (Black)
1
6
02011002
O-Ring for 1.5" Valve Lid
1
7
01181002
Washer for Spring
1
8
03014001
Spring for 1.5" Top/Side Mount Valve
1
9
02011022
O-Ring for Valve Rotor
2
10
01021001
1.5" Valve Rotor
1
11
02311002
Spider Gasket
1
12
E190147
1.5" Body with Diffuser (Black)
1
13
02011001
O-Ring for Diffuser
1
14
02020013
O-Ring for 1.5"Connector
3
15
01013015
1.5" Connector (Black)
3
16
02011003
O-Ring for 1.5" Adaptor
3
17
01171153
1.5" Union (A/E)(Black/White)
2
18
01013017
1.5" Union Nut (Black)
3
19
01041002
1.5" Union with Sight Glass (Short)
1
20
01172026
1.5" Union with Sight Glass Holder(Black/White)
1
21
89280120
Drain Plug Fitting with O-ring
1
22
89021307
Drain Plug with O-ring
1
23
06021013
Plastic Pressure Gauge with O-ring
1