emaux SS Series User manual

EMAUX WATER TECHNOLOGY CO., LTD
STRIVE FOR CLEAR WATER
www.emauxgroup.com
USER MANUAL
SS, SS-T SERIES
CENTRIFUGAL PUMP
Installation and Operation Manual
geprüfte
Sicherheit SAA
EMPU21062401

THE BEST OPTION FOR SMALLER PLUMBING
TABLE OF
CONTENT
PAGE
2
....
4
5
....
....
....
1.PRODUCT INFORMATION
WARNINGS AND SAFETY INSTRUCTIONS
2.INSTALLATION
3.START UP
5.WINTERIZING
....
6. TIMER SETTING(FOR TIMER VERSION)
10
....
7. TROUBLE SHOOTING
12
....
8. REPLACEMENT PARTS
15
....
.... 4.ROUTINE MAINTENANCE
CENTRIFUGAL PUMP
P1 CONTENT
7
9
9
9. TERMS OF THE WARRANTY
19
....
This Limited Warranty extends only to products purchased from Emaux authorized
reseller. This Limited Warranty does not extend to any product that has been damaged or
rendered defective (a) as a result of accident, misuse or abuse;
(b) as a result of an act of God;
(c) by operation outside the usage parameters stated herein;
(d) by the use of parts not manufactured or sold by Emaux;
(e) by modification of the product;
(f) as a result of war or terrorist attack; or
(g) as a result of service by anyone other than Emaux authorized reseller or authorized
agent.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, EMAUX MAKES NO OTHER
WARRANTIES EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OR
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. EMAUX EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
EXPRESS LIMITED WARRANTY.
TERMS OF THE WARRANTY P18

WARNINGS AND SAFETY INSTRUCTIONS
GENERAL WARNING
This instruction contain general caution information for use in Pool and SPA pump installation
application. Specified Pump model function should be refer to particular manual. Components such
as the filtration system, pumps and heater must be positioned so as to prevent their being used as
means of access to the pool by young children.
This appliance should be installed by qualified electrical personnel
in accordance with National Electrical Code and all applicable
local codes and ordinances.Hazardous voltage can shock, burn,
and cause death or serious property damage. DO NOT use an
extension cord to connect unit to electric supply to reduce the risk
of electric shock.
1.The pump should be permanently connected to an individual circuit breaker.
2.Pump must be connected to a residual current device (RCD) having a rated residual operating
current notexceeding 30 mA or receptacle with ground fault circuit interrupt (GCFI).
3. Electrical grounding must be connected before connecting to electrical power. Failure to ground all
electrical equipment can cause serious or fatal electrical shock hazard.
4.Bonding: Use at least #8 AWG (#6 AWG for Canada) a solid copper conductor, run a continuous wire
from external bonding lug (if available) to the pressure wire connector provided on the electrical
equipment and to all metal parts of swimming pool, spa, or hot tub, and metal piping (except gas
piping), and conduit within 1.5 m (5 ft) of inside walls of swimming pool, spa, or hot tub.
5.Never open the inside of the drive motor enclosure. There is a capacitor bank that holds a mains
supply voltage charge even when there is no power to the unit. The voltage should be referred to
the individual pump operation voltage.
6.The pump is capable of high flow rates; use caution when installing and programming to limit
pumps performance only.
7.Switch OFF pump power before servicing and disconnecting the main circuit to the pump.
8.Never change the filter control valve position while the pump is running.
RISK OF ELECTRICAL SHOCK
COMPRESS AIR HAZARDOUS
This system enclosed pre-filter / filter and become pressurized.
Pressurized air can cause the Lid to separate which can result in
serious injury or death.
Pool and spa circulation systems operate under high pressure. When any part of the circulating
system (i.e. lock ring, pump, filter, valves, etc.) is serviced, air can enter the system and become
pressurized. Filter tank Lid and pre-filter cover must be properly secured to prevent violent
separation. Place pre-filter / filter air relief valve in the open position and wait for all pressure in the
system to be relieved before remove the lib to access the basket for cleaning.
HYPERTHERMIA
SPA water temperature excess 38°C (104°F) may be injurious to
health. Measure water temperature before entering SPA.
Hyperthermia occurs when the internal temperature of the body
reaches a level several degrees above the normal body
temperature of 98.6°F (37°C). The symptoms of hyperthermia
include drowsiness, lethargy, and an increase in the internal temperature of the body.
WARNINGS AND SAFETY INSTRUCTIONS P2
STAND CLEAR OF PUMP DURING START-UP
9. TERMS OF THE WARRANTY
As original purchaser of this equipment have purchased from Emaux Water Technology
Co Ltd, through Authorized International Distributor or Dealer, warrants its products free
from defects in materials and workmanship under normal use during warranty period.
The warranty period begins on the day of purchase and extends only to the original
purchaser. It is not transferable to anyone who subsequently purchases the product from
you. It excludes all expendable parts.
During the warranty period, Emaux authorized reseller will repair or replace defective
parts with new parts or, at the option of Emaux, serviceable used parts that are
equivalent or superior to new parts in performance.
P17 TERMS OF THE WARRANTY
18
18
18
18
18
19
21
21
22
22
23
23
24
106241439
106241443
106241444
106241421
106241424
1062570102
4202870076
4202770076
01031027
01031026
01031011
01031010
02011104
Capacitor for SS020T Pump (220V/50Hz)
Capacitor for SS033T Pump (220V/50Hz)
Capacitor for SS050T Pump (220V/50Hz)
Capacitor for SS075T Pump (220V/50Hz)
Capacitor for SS100T/120T Pump (220V/50Hz)
PCB
Wire box top cover
Wire box bottom cover
Cooling Fan for SS020T/033T Pump
Cooling Fan for SS050T-120T Pump
Fan Cover for SS020T/033T Pump
Fan Cover for SS050T-120T Pump
O-Ring for 1.5" Union
1
1
1
1
1
1
1
1
1
1
1
1
2
Key No. Part No. Description QTY

SUCTION ENTRAPMENT HAZARD
This pump produces high levels of suction and creates a strong
vacuum at the main drain at the bottom of your pool and spa. This
suction is so strong that it can trap adults or children under water if
they come in close proximity to a pool or spa drain or a loose or
broken drain cover or grate.
The Virginia Graeme Baker (VGB) Pool and Spa Safety Act creates
new requirements for owners and operators of commercial
swimming Pools and spas.
Commercial pools or spas constructed on or after December 19, 2008, shall utilize:
1. A multiple main drain system without isolation capability with suction outlet covers that meet
ASME/ANSI A112.19.8a Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, and Hot
Tubs and either:
1.1 A safety vacuum release system (SVRS) meeting ASME/ANSI A112.19.17 Manufactured Safety
Vacuum Release systems (SVRS)
For Residential and Commercial Swimming Pool, Spa, Hot Tub, and Wading Pool Suction
Systems and/or ASTM F2387 Standard
Specification for Manufactured Safety Vacuum Release Systems (SVRS) for Swimming pools,
Spas and Hot Tubs or
1.2 A properly designed and tested suction-limiting vent system or
1.3 An automatic pump shut-off system.
Commercial pools and spas constructed prior to December 19, 2008, with a single submerged suction
outlet shall use a suction outlet cover that meets ASME/ANSI A112.19.8a and either:
1. A SVRS meeting ASME/ANSI A112.19.17 and/or ASTM F2387, or
2. A properly designed and tested suction-limiting vent system, or
3. An automatic pump shut-off system, or
4. Disabled submerged outlets, or
5. Suction outlets shall be reconfigured into return inlets.
There are five types of suction entrapment according to The Virginia Graeme Baker (VGB) Pool and Spa
Safety Act
1.Body Entrapment a section of the torso becomes entrapped
2.Limb Entrapment an arm or leg is caught by or pulled into an open drainpipe
3.Hair Entrapment or entanglement hair is pulled into and/or wrapped around the grate of the drain
cover
4.Mechanical Entrapment the bather's jewelry or clothing gets caught in the drain or the grate
5.Evisceration the victim's buttocks come into contact with the pool suction outlet and he or she is
disemboweled
TO REDUCE ENTRAPMENT HAZARD RISK
Two function suctions outlets per pump must be installed to prevent entrapment.
The minimum separate of suction on the same plate must be at least point to point
measurement 1 meter (3ft) apart. It is used to avoid “dual blockage” by bather.
If suction is found damage, broken, cracked, missing or not securely attached during
regular checking, shunt down the pool and replace it immediately.
A vacuum release or vent system is recommended to install for suction entrapment release.
P3 SUCTION ENTRAPMENT HAZARD
Key No. Part No. Description QTY
1
2
3
4
5
6
7
8
9
9
9
9
9
9
10
11
12
13
14
15
16
17
17
17
17
17
01201031
02010247
01112051
01021064
89280105
89022402
02011004
01111014
01311015
01311016
01311017
01311018
01311019
01311014
89022403
04015033
02011090
01021065
03011035
02011156
89022404
104007375
104007374
104001151
104001154
104001158
Transparent Lid
O-Ring for Lid
Basket
SS Pump Pre-Filter
1.5" Union
Drain Plug With O'Ring
O-Ring for Diffuser
Diffuser
Impeller SS020(220V/50Hz)
Impeller SS033(220V/50Hz)
Impeller SS050(220V/50Hz)
Impeller SS075(220V/50Hz)
Impeller SS100(220V/50Hz)
Impeller SS120(220V/50Hz)
M8 x 16 Screw with Washer
1/2" Mechanical Seal
O-Ring for Flange
SS Pump Flange
M6 x 30 Screw
Motor Slinger
Motor Support
Motor SS020T(220V/50Hz)
Motor SS033T(220V/50Hz)
Motor SS050T(220V/50Hz)
Motor SS075T(220V/50Hz)
Motor SS100T/120T(220V/50Hz)
1
1
1
1
2
1
1
1
1
1
1
1
1
1
4
1
1
1
8
1
1
1
1
1
1
1
REPLACEMENT PARTS P16

1. PRODUCT INFORMATION
DIMENSIONS
Model
50Hz Current
(AMP)
Head(m)
4
FlowRate(m³/h)
SS020 / SS020T
SS033 / SS033T
SS050 / SS050T
SS075 / SS075T
SS100 / SS100T
SS120 / SS120T
0.28
0.43
0.55
0.75
0.90
0.97
Input
(kW)
1.5
2
2.5
3.5
4.7
5.8
68
8.4
10.4
12.4
14.4
15.2
18
4
7
10
12.2
13.8
16
Noise
(dB)
55
55
60
60
65
65
2
211
195
340
A
88022401
88022402
88022403
88022404
88022405
88022406
9020329
9020330
9020331
9020332
9020333
9020334
Code
220V/50Hz
Model
Connection
Size
Horsepower
Capacitance
220V
A
mm
Weight
(kg)
Code
110V/60Hz
Capacitance
110V
88022601
88022602
88022603
88022604
88022605
88022606
/
/
/
/
/
/
SS020
SS033
SS050
SS075
SS100
SS120
SS020T
SS033T
SS050T
SS075T
SS100T
SS120T
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
1.5”/50mm
0.2hp
0.33hp
0.5hp
0.75hp
1.0hp
1.2hp
0.2hp
0.33hp
0.5hp
0.75hp
1.0hp
1.2hp
6.20
6.50
8.03
9.01
9.09
11.00
6.20
6.50
8.03
9.01
9.09
11.00
5µF
6µF
8µF
14µF
20µF
20µF
5µF
6µF
8µF
14µF
20µF
20µF
507
507
552
552
552
552
507
507
552
552
552
552
20µF
24µF
30µF
40µF
60µF
60µF
/
/
/
/
/
/
PRODUCT INFORMATION P4
-
-
4
9.4
11.4
14
-
-
-
5
8.4
12
Notes: 5* 89280105B is 1.5" Union in Black Colour
5* 89280105W is 1.5" Union in White Colour
SS SERIES WITH TIMER
1
2
3
4
5
10
12 13 14
20
19
18
21
24
18
18
19
20
21
22
22
23
23
24
04016030
04016031
89022112
89022111
89021505
01031027
01031026
01031011
01031010
02011104
Capacitor for SS/SD/SQ/ST020 AMU020P/TP(50/60Hz)
Capacitor for SS/SD/SQ/ST033 Pump
Cable Box for SD,SQ,SP,ST050-120 Pump
Cable Box for SQ/ST/SD020-033, SS020-SS030 Pump
Cable Box for SA/ ST/ SD 110V
Cooling Fan for SS/SD/SQ/ST050-SS/SD/SQ/ST120 Pump
Cooling Fan for SS/SD/SQ/ST020-SS/SD/SQ/ST030 Pump
Fan Cover for SS/SD/SQ/ST020-SS/SD/SQ/ST030 Pump
Fan Cover for SQ/SP/SS/SD/ST050-SQ/SP/SS/SD/ST120
O-Ring for 1.5" Union
1
1
1
1
1
1
1
1
1
2
Key No. Part No. Description QTY
678911 15 17
16 22 23
P15 REPLACEMENT PARTS

80
0
10
20
30
40
14 16 18 20 Q(m³/h)
Q(LPM)
250 300 350
20 40 60
4 6 8 10 12
50 100 150 200
12
10
8
6
4
2
0
H(m)
U.S.g.p.m
0
2
0
SS020
SS033 SS050
SS075
SS100
SS120
P5 INSTALLATION
PERFORMANCE CURVE
2. 1 PIPING
2. INSTALLATION
1.
2.
3. B
4.
5.
6.
7.
8.
9.
Locate the system below the pool water line, for best pump performance.
Install the pump as close to the pool as possible, preferably in a dry, well ventilated
area away from
direct sunlight. Protect the pump from excessive moisture.
efore installing the pump, make sure that the surface is solid, elevated, rigid and
vibration free.
Secure the pump to the base with screws or bolts to limit the vibration and the stress
on the pipe or
the joints.
Leave enough space for gate valves in suction and discharge piping, if required.
Ensure there is enough clearance for pre-filter basket & Lid open and motor
ventilation.
Connect the suction and discharge pipe to the outlet and inlet of the swimming pool.
Make sure that floor drainage is adequate to prevent flooding.
Make sure that the pump and piping are accessible for servicing.
14
15
16
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
18
18
18
18
18
18
18
18
13
03011035
02011156
89022404
89022109
89022110
89022105
89022106
89022107
89022108
89022201
89022202
89022203
89022204
89022205
89022206
89022305
89022306
89022301
89022302
89022303
89022304
04016028
04016019
04016021
04016009
04016010
04016012
04016032
04016033
01021065 SS Pump Flange
M6 x 30 Screw
Motor Slinger
Motor Support
Motor SD020/SQ020/SS020/ST020(220V/50Hz)
Motor SD033 (220V/50Hz)
Motor SD050/SQ050/SS050/ST050(220V/50Hz)
Motor SD075/SQ075/SS075/ST075(220V/50Hz)
Motor SD100/SQ100/SS100/ST100(220V/50Hz)
Motor SD120/SQ120/SS120/ST120(220V/50Hz)
Motor SD/SQ/SS/ST020(220V/60Hz)
Motor SD/SQ/SS/ST033(220V/60Hz)
Motor SD/SQ/SS/ST050(220V/60Hz)
Motor SD/SQ/SS/ST075(220V/60Hz)
Motor SD/SQ/SS/ST100(220V/60Hz)
Motor SD/SQ/SS/ST120(220V/60Hz)
Motor SD/SQ/SS/ST020(110V/60Hz)
Motor SD/SQ/SS/ST033(110V/60Hz)
Motor SD/SQ/SS/ST050(110V/60Hz)
Motor SD/SQ/SS/ST075(110V/60Hz)
Motor SD/SQ/SS/ST100(110V/60Hz)
Motor SD/SQ/SS/ST120(110V/60Hz)
Capacitor for SS/SD/SQ/ST050 Pump 110V
Capacitor for SC050 & SS/SD/SQ/ST075 Pump 110V
Capacitor for SC075 & SS/SD/SQ/ST100-124 Pump 110V
Capacitor for SS/SD/SQ/SP/ST050 Pump
Capacitor for SS/SD/SQ/SP/ST075 & SC050 Pump
Capacitor for SS/SD/SQ/SP/ST100-120
Capacitor for SS/SD/SQ/ST020 Pump 110V
Capacitor for SS/SD/SQ/ST033 Pump 110V
Key No. Part No. Description QTY
REPLACEMENT PARTS P14
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

2.2 ELECTRICAL WIRING
This power pump demand licensed or certified electrician
or qualified pool installer to ensure there is adequate
protection between the pump motor and mains power
supply according to individual countries safety code.
The pump has power cord with plug attached on the plug,
plug it to a power socket with circuit breaker to isolate the motor from the mains power
for over load protection. The circuit breaker rating should refer to the electrical
specification of individual pump working voltage and power.
The power has to be with a Residual Current Device (RCD) or Ground Fault Circuit
Interrupt (GFCI) having a rated residual operating current not exceeding 30 mA.
If the RCD/GFCI device trips, it means there is fault on the power line or
motor. Do not use this pump. Disconnect the pump and have the
problem corrected by a qualified service representative before using.
Press the reset button to reset the RDC/GFCI devices after fixed. It will
keeps the circuit shut off and will not reset if the power line problem is not fixed.
It is recommend to test the RCD/GFCI at least once a month.
Pumps should be shipped with Power cord with plug for corresponding countries
INSTALLATION P6
Pool Water Line
Return to Pool
Power Cord to Power Receptacle
From Pool
Above Ground Pool Pump
Sand Filter
Waste
P13 REPLACEMENT PARTS
8. REPLACEMENT PARTS
1
578910
11
12 13
15
14 16
2
3
4
6
17
24
17
17
17
18
21
19
22 23
18
18 20
22 23 22 23
(220V/50Hz) (220V/50Hz) (110V/60Hz)
17 17
Key No. Part No. Description QTY
1
2
3
4
5*
6
7
8
9
9
9
9
9
9
9
9
10
11
12
01201031
02010247
01112051
01021064
89280105
89022402
02011004
01111014
01311014
01311015
01311016
01311017
01311018
01311019
01311023
01311024
89022403
04015033
02011090
Transparent Lid
O-Ring for Lid
Basket for SS Pump
SS Pump Pre-Filter
1.5" Union (Black/ White Colour)
Drain Plug With O'Ring
O-Ring for Diffuser
Diffuser
Impeller SS120(220V/50Hz)
Impeller SD020/SD50/SQ20/SQ50/SS20/SS50/ST20/ST50
Impeller SD33/SD75/SQ33/SQ75/SS33/SS75/ST33/ST75
Impeller SD050/SD100/SQ050/SQ100/SS050/SS100/ST050
Impeller SD075/SD120/SQ075/SQ120/SS075/SS120/ST075
Impeller SD100/SQ100/SS100/ST100(220V/50Hz)
Impeller SD020/SQ020/SS020/ST020(220V,110V/60Hz)
Impeller SD033/SQ033/SS033/ST033(220V,110V/60Hz)
M8 x 16 Screw with Washer
1/2" Mechanical Seal
O-Ring for Flange
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
4
1
1

P7 START UP
3. START UP
1. Verify the pump shaft turn freely.
2. Check the mains voltage, current and frequency are accordingly to the
name plate.
3. Never run pump dry! Running pump dry may cause damage to the
mechanical seal causing leakage and flooding. Fill the pre-filter with
water before starting motor.
4. Before removing the pre-filter Lid, STOP PUMP, CLOSE GATE VALVES in suction and
discharge pipes.
5. Always STOP THE PUMP before when RELEASE ALL PRESSURE from the pump and the
piping system before proceeding.
6. Never tighten or loosen screw while the pump is in operation.
7. The suction pipe and the suction inlet in the pool must be free from obstruction.
WARNING: Tighten / untighten the pump Lid by hand only.
Bonding Instructions – Permanently wired units will need to include
instructions for connecting the solid copper, equipotential bonding
conductor. For SS020, SS033, SS050, SS07 and SS120 110V/60Hz
version, the size of the bonding conductor should be No. 8 AWG. For Canada the size of
the bonding conductor should be No. 6 AWG. Bonding Nut location is as photo.
7. TROUBLE SHOOTING
Pump delivers no water
Leakage of water at the shaft
Low pump capacity
1. Valve in the suction or discharge line partly closed
2. Suction or discharge line partly plugged
3. Suction or discharge line too small
4. Plugged basket in skimmer or hair and lint pre-filter
5. Dirty filter
6. Impeller clogged
1.Shaft seal requires replacement
1.Pump is not primed
2.Closed valve in suction or discharge line
3.Leakage or air into suction system
4.Impeller clogged
High pump pressure 1. Discharge vale or inlet fittings closed too much
2. Return lines too small
3. Dirty filters
Noisy pump and motor
1.Plugged basket in skinner or hair in lint pre-filter
2.Worn motor bearings
3.Valve in suction line partly closed
4.Suction line partly plugged
5.Vacuum hose plugged or too small
6.Pump not supported properly
1.Leakage of air into the suction line in connections or valve stem
2.Cover gasket of hair and lint pre-filter needs cleaning
3.Low water level in the pool
Air bubbles at inlet fittings
Problem description Possible causes
Motor does not start
1.Disconnect switch or circuit breaker in off position
2.Fuses blown or thermal overload open
3.Locked motor shaft
4.Motor windings burned out
5.Defective starting switch inside single phase motor
6. Disconnected or defective wiring
7.Low voltage
Pump does not reach full speed 1. Low voltage
2. Pump connected to the wrong voltage
Motor overheats
(protector trips)
1. Low voltage
2. Motor windings connected to the wrong voltage on dual voltage model
3. Inadequate ventilation
Note: If the above recommendations of this manual do not solve your particular problem(s),
please contact your local service agent for further assistance.
TROUBLE SHOOTING P12

1. Clear all piping of construction debris and verify that the piping has passed a proper
pressure test.
2. Check the filter and other equipment for proper installation, verifying all clamps and
connections are properly installed as per the manufacturer's instructions.
3. Open any shut off valves on the suction and discharge lines.
4. Open the filter pressure relief valve and release all pressure from the system.
5. If the pump is located below the water level of the pool, opening the pressure relief
valve will fill the pump with water.
6. If the pump is located above the pool water level, remove the Lid from the pre-filter
and fill with water before starting the pump.
7. Check to see that the Lid O-ring and seat areas are clean and lubricated. Debris in the
sealing area can cause air to leak into the system and make it difficult to prime the
pump.
8. Close/tighten the Lid to make an airtight seal.
9. Turn on the pump.
10. If the pump does not prime within 15 minutes. Ensure all instructions to this point
have been followed. Stop the pump! Check for suction leaks and repeat steps (I)
through (VIII).
Before start-up, the alignment of the pump should be checked. The
tubing should be inspected to ensure that they are properly fitted and
tightened and that they do not exert pressure or tension on the pump's
suction or discharge connection. The pump should never be operated.
START UP P8
P11 TIMER SETTING(FOR TIMER VERSION)
6.3 Single Cycle Mode
To switch to Single Cycle Mode, press [timer]
for about 3 seconds (the Single Cycle Indicator
will come on). To change cycle time, press the
[timer] button again. It works in a sequence
and will change from 2h →4h →6h →8h →
10h →12h →16h →24h →2h.
When the timer is set to 2h, the pump will
operate and stop after 2 hours until the pump
is switched on again.
Unscrew the 4 screws on the
lid of the terminal box and
remove the lid.
Remove the battery. Remove the rubber film on the
surface of the battery.
Replace the battery. Replace the lid of the terminal box
and tighten the 4 screws with a
screwdriver.

ON/OFF
Button Timer Indicator Timer Button Single Cycle Indicator
Timer Control Panel
P9 ROUTINE MAINTENANCE
6. TIMER SETTING(FOR TIMER VERSION)
6. 1 CONTROL PANEL
6. 2 Continuous Mode
After turn on the pump, the default setting is
24 hours continuous operation. To set the
desired operation period, this can be done by
pressing the timer button (2h →4h →6h →
8h →12h →16h →24h →2h).
For example, if you set the timer to 2h and
press [on] at 08:00, the pump will operate for
2 hours within the 24 hours period zone
(indicated by the 2h light flashing; the light
will stop flashing when the pump stops). The
pump will start again for 2 hours at 08:00 the
following day.
TIMER SETTING(FOR TIMER VERSION) P10
4. ROUTINE MAINTENANCE
The pump mechanical seal requires no lubrication and service.
The only routine maintenance needed is the inspection and cleaning of the pre-filter
basket. Debris or trash collected in the basket will choke off the water flow through the
pump. Follow the instructions below in order to clean the pre-filter basket:
1.Turn off the pump, close the gate valve in suction and discharge, and release all
pressure from the system before proceeding.
2.Turn the transparent Lid cover follow the arrow on the Lid cover to release and lock the
Lid ring.
3.Remove the pre-filter basket and cleaning. Make sure all the holes in the basket are
clear, flush the basket with water and replace it in the trap with large opening at the pipe
connection port (between ribs provided). If the basket is replaced backwards, the cover
will not fit on the trap body.
4.Clean and inspect the Lid's O-ring ring; reinstall on the Lid cover.
5.Clean the ring groove on the pre-filter body and replace the Lid. To help keep the Lid
from sticking, tighten it by hand only.
6.Put back the basket with opening face to suction inlet directly.
7.Fill up the filter body with water and Prime the pump.
5. WINTERIZING
If the air temperature drops below 0°C (35°F), the water in the system can freeze and
cause damage. Freezing damage is not warrantable.
To prevent freezing damage follow the procedures listed below:
1.Shut off electrical power for the pump at the house circuit breaker.
2.Drain the water out of the pump case by removing the two drain plugs from the case.
3.Store the plugs in the pump basket.
4.Cover the motor to protect it from severe rain, snow and ice.
5.If it is possible, store the pump in a dry location during this time.
6.Do not wrap the motor in plastic. It will cause condensation and rust on the inside of
the motor.