emaux FSM24-6W User manual

INSTALLATION
Installation & Operating Instruction
EMFS15122452
FSM24-6W
FILTER & PUMP COMBO
1-4
名 称
版 本 编 号
规 格
比 例
颜 色
产品负责人
更改日期
更改内容
新文件
版本 制图/设计
A
意万仕(中山)泳池设备有限公司
EMAUX ZhongShan)Swimming Pool Equipment Co., Ltd(
审核 批准
80g印尼蓝
普通印刷
2015.12
1 : 1
420X297(mm)
EMFS15122452
PANTONE Process Black C
材料
工 艺
日 期
* Install filtration system including pump,filter tank and multiport valve.
* The filter system should be installed as close as possibie to the swimming pool and preferably at a
level of 0.50 metres below the surface of the water in the swimming pool. Make sure there is
drainage available at the place where the filter is to be installed.
* PUMP
1) Only qualified,licensed personnel should install pump and wiring.
2) Electrical Contractors Please Note:All 220 volt 50Hz pump must be wired to the main power supply
trough an approved and correctly rated contractor.
3) Allow for gate valve in suction piping.
4) Pump suction and discharge connections have moulded in thread stops,do not try to screw pipe in
beyond these stops.
* FILTER TANK and MULTIPORT VALVE
1) Loading the sand media.Filter sand media is loaded through the top opening of the filter.
a) Loosen the plastic clamps from tank neck.
b) Cap internal pipe with plastic cap to prevent sand from entering it.
c) We recommend filling tank approximately 1/2 way with water to provide a cushion effect when
the filter sand is poured in. This helps protect the under-drain laterals from excessive shock.
d) Carefully pour in correct amount and grade of filter sand. Be sure center pipe remains centered in
opening. Sand surface should be leveled and should come to about the middle of the filter
tank.Remove plastic cap from internal pipe.
2) Assemble filter control valve to filter tank.
a) Insert filter control valve(with O'ring in place)into the tank neck, taking care that the center pipe
slips into the hole in the bottom of the valve.
b) Place two plastic clamps around valve flange and tank neck and tighten just enough so that the
valve mayBe rotated on tank for final positioning.
c) Carefully screw pressure gauge(with O'ring in place)into tapped hole in valve body.Do not over-
tighten.
d) Connect pump to control valve opening marked PUMP with hose. After connections are made,
tighten clamps with screwdrive, tapping around clamp with screwdrive handle to help seat valve
flange clamp.
3) Make return to pool pipe connection to control valve opening marked RETURN and complete
other necessary plumbing connections, suction lines to pump,waste,etc.
4. To prevent water leakage, be sure all pipe connections are tight.
WARNING
By-passes filter for circulating water to pool
Used after backwash to flush dirt from valve
Cleaning Filter by reversing the flow
By-passes filter, used for vacuuming to waste or lowering water level
CLOSED Shuts off all flow to filter or pool
RECIRCULATE
WASTE
RINSE
BACKWASH
FILTER
Valve Position Normal Filtration and Vacuuming Function
VALVE REPLACEMENT PARTS
4-4
THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING SYSTEM
(e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE SYSTEM AND
BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO BE BLOWN OFF
WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE.
TURN PUMP OFF BEFORE CHANGING VALVE POSITION.
TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM.CLEAN
PUMP STRAINER AND SKIMMER BASKETS REGULARLY.
DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.
!
!
!
!
Key No.
Part No.
Description
Qty
1
01013003
Handle (Big)
1
2
03018008
Pin for Handle
1
3
01181027
Washer for Handle
1
4
01181029
Defend Lock
1
5
01020003
1.5" Lid
1
6
01181002
Washer for Spring
1
7
02011022
O-Ring for Valve Rotor
2
8
03014001
Spring
1
9
89280701
1.5" Valve Rotor with Spider Gasket
1
10
02010002
O-Ring for Lid
1
11
01020004
1.5" Body
1
12
02020013
O-Ring for 1.5"Connector
3
13
01013015
1.5" Connector (Black)
3
13
01051013
1.5" Connector (White)
3
14
02011003
O-Ring for 1.5" Adaptor
3
15
01171153
1.5" Union (A/E)
3
16
01013017
1.5" Union Nut (Black)
3
16
01051014
1.5" Union Nut (white)
3
17
89280120
Connector for Pressure Gauge with O-Ring
1
18
89021307
Drain Plug with O-Ring
1
19
06021013
Pressure Gauge with O-Ring (40Psi)
1
20
89280104
Sight Glass with O-Ring
1
21
02011001
O-Ring for Diffuser
1
22
01100002
1.5" Diffuser
1
1
2
3
4
5
6
7
8
9
10
11
1213 14 15
1819
20
21
22
16
17

REPLACEMENT PARTS OF FILTER
INSTALL/START-UP OF FILTRATION
SC PUMP REPLACEMENT PARTS
PRIMING PUMP
2-4
3-4
1 Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2 Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always
depress handle before turning.)
3 Prime and start pump. Never tun pump dry! Running pump dry may damage seals,causing leakage and flooding!
Fill pump with water before starting motor. (be sure all suction and return lines are open), allowing the filter tank to
fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial back-
washing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4 Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2
to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the
normal filter mode, filtering dirt particles from the pool water.
5 Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
connections, bolts, nuts, as required.
6 Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation
in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is 1.5 bar, higher
than the initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under filter and control
valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
)
)
)
)
)
)
Release all air from filter and piping system.
In a flooded suction system (water source higher than pump), pump will prime itself when suction and
discharge valves are opened.
If pump is not in a flooded suction system, unscrew and remove trap cover; fill trap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace trap cover on trap; turn clockwise to tighten cover.
NOTICE: Tighten trap cover by hand only .Pump should prime now. Priming time will depend on vertical
length of suction lift and horizontal length of suction piping.
Key NO.
Part Number
Product Description
QTY
Key NO.
Part Number
Product Description
QTY
1
01041043
Transparent Lid
1
15
02011096
Motor Slinger
1
2
02011077
O-Ring for lid
1
16
89021705
Motor SC050(220V/50HZ)
1
3
01111076
Basket
1
89021706
Motor SC075(220V/50HZ)
1
4
89280105
1.5"union
2
89021707
Motor SC100(220V/50HZ)
1
5
89021307
Drain Plug With O-ring
1
89021708
Motor SC150(220V/50HZ)
1
6
01111006
SC Pump Body
1
89021709
Motor SC200(220V/50HZ)
1
7
02011105
O-ring for Diffuser
1
17
01021022
Opening Key
1
8
01111009
Diffuser
1
18
01111007
SC Pumps Base
1
9
89021309
Impeller Screw with O-ring
1
19
89021311
Cable Box for SC Pump
1
10
01311009
Impeller SC050(220V/50HZ)
1
20
89021505
Cable Box for SC Pump
1
01311010
Impeller SC075(220V/50HZ)
1
21
04016010
Capacitor for SC050 Pump
1
01311011
Impeller SC100(220V/50HZ)
1
04016012
Capacitor for SC075 Pump
1
01311012
Impeller SC150(220V/50HZ)
1
04016014
Capacitor for SC100-SC150 Pump
1
01311013
Impeller SC200(220V/50HZ)
1
04016015
Capacitor for SC200 Pump
1
11
04015032
3/4"Mechanical seal
1
22
01031007
Cooling fan for SC Pump
1
12
02011089
O-ring for Flange
1
23
01031009
Fan Cover
1
13
01111008
SC Pump Flange
1
24
02011104
O-Ring
2
14
01021014
Ring Lock Nut
1
1
2
3
4
5
67 8 10 12 13 18 17
24
911 14 15 16 16 19 21
22 23
1
3
4
56
7
8
9
10
11
13
14
12
2
Item
Part No.
Description
QTY
1
88281505
1.5"Clamp Type Multiport Valve
1
2
06021013
Plastic Pressure Gauge With O-Ring
(40psi)
1
01111048
Connector for Pressure Gauge/Stopper
1
3
89280102
1.5"Union Set (3Pieces)With O-Ring
for MPV07 Valve
3
4
89033701
FPlastic Hose with NutSM24-6W
1
5
02011104
O-Ring for Pump
2
6
08030004
F PumpSM24-6W (SC150)
1
7
89032001
Pump Assembly Screw
4
8
01111053
FCombo BaseSM24-6W
1
9
89011601
Water Drain Set
1
10
01172008
Laterals (126mm)for F)SM24-6W
8
11
89012509
Lateral Assembly with Center Pipe for
FSM24-6W
1
12
01331026
FFilter TankSM24-6W
1
13
02010007
O-Ring
1
14
89012512
Clamp Kit
1