Emerson SAPAG User manual

Pressure Seal Gate Valves -Style A-
Installation and Maintenance Instructions
Emerson reserves the right to change the contents without notice SAPLT-0028-EN-1308
Section 1 - Valve Storage
1.1 Preparation and Preservation for Shipment
All valves are properly packed in order to protect the parts that are subject to deterioration during
transportation and storage on site. In particular, the following precautions should be taken:
1. The valves must be packed with the wedge in the closed position.
2. The weld ends surface shall be protected with suitable protective like Deoxaluminite. The end
shall be closed with plywood or plastic disc fixed at the edge by strips.
3. All actuated valves must be carefully securely palleted or crated, in order to ensure that the
parts of actuator (especially pneumatic piping or accessories) do not extend beyond the skid/
crate.
4. The type of packing must be defined in the Customer’s Order and shall be appropriate to ensure
safe transportation to final destination and eventual conservation before installation.
Cast Gate Valves Pressure Seal -Style A-
Wedge Gate and Parallel Slide Configuration
1.2 Handling Requirements
A - Packed Valves
Crates: Lifting and handling of the packed valves in crates will be carried out by a fork lift truck, by
means of the appropriate fork hitches.
Cases: The lifting of packed valves in cases should be carried out in the lifting points and at
the center of gravity position which have been marked. The transportation of all packed
material must be carried out safely and following the local safety regulations.
B - Unpacked Valves
1. The lifting and the handling of these valves has to be carried out by using appropriate means
and at respecting the carrying limits. The handling must be carried out on pallets, protecting the
machined surfaces to avoid any damage.
2. With valves of large dimensions, the sling and the hooking of the load must be carried out using
the appropriate tools (brackets, hook, fasteners, ropes) and load balancing tools in order to
prevent them from falling or moving during the lifting and handling.
Contents
1 Valve Storage 1
1.1 Preparation and Preservation for Shipment 1
1.2 Handling Requirements 1
1.3 Storage and Preservation before Installation 2
2 Installation 2
2.1 Preparation before Installation 2
2.2 Installation Instructions 3
2.3 Valve Verification before Start Up 3
2.4 Operations Instructions 3
Table I: Bolt Torque Figures for Packing Bolts 4
Table II: Bolt Torque to Ensure Tightness of Pressure Seal Gasket 4
2.5 Periodic Valve Verification during Service 4
Troubleshooting Guide 4
3 Maintenance 5
3.1 Packing Maintenance 5
3.2 Bonnet Gasket Replacement 5
4 Valve Removal 6
5 Greases and Special Tools 6
5.1 Greases 6
Table III: Grease and Lubricant List 6
5.2 Special Tools 6
SAPAG
www.valves.emerson.com

Pressure Seal Gate Valves -Style A-
Installation and Maintenance Instructions
Emerson reserves the right to change the contents without notice page 2
1.3 Storage and Preservation before Installation
In case the valves have to be stored before installation, the storage has to be carried out in a
controlled way, and has to be performed in accordance with the following criteria:
1. The valves have to be stocked in a closed, clean and dry storage room.
2. The wedge must be in the closed position, and the end faces must be protected with plastic or
wooden discs fixed with straps. If possible, keep the original protection.
3. Periodical checks have to be carried out in the storage area to verify that the above mentioned
conditions are maintained.
For actuated valves, in addition to the above, please refer to the warnings in the manual of the
actuator.
Caution
For valve handling and/or lifting, the lifting equipment (fasteners, hooks, etc.) must be sized and
selected while taking into account the valve weight indicated in the packing list and/or delivery
note. Lifting and handling must be made only by qualified personnel.
Do not use the lifting points located on the actuator, if any, to lift the valve. These lifting points are
for the actuator only.
Caution must be taken during the handling to avoid that this equipment passes over the workers
or over any other place where a possible fall could cause damage. In any case, the local safety
regulations must be respected.
Section 2 - Installation
2.1 Preparation before Installation
1. Carefully remove the valve from the shipping package (box or pallet) avoiding any damage to
the valve or, in case of automated valves, to the electric or pneumatic/hydraulic actuator or
instrumentation.
2. Clean the inside of the valve using an air line. Ensure that there are no solid objects such as
pieces of wood, plastic or packing materials within the valve or on the valve seat.
3. Confirm that the materials of construction listed on the valve nameplates (service and
temperature) are appropriate for the service intended and are as specified.
4. Define the preferred mounting orientation with respect to the system pressure. If any (see arrow
on the body), identify the upstream side (high pressure) and downstream side (low pressure).
Note
Storage in an open area for a limited period can be considered only in case the valves have
appropriate packing (packed in cases lined with tarred paper, and contents well protected with
barrier sacks).
Do not place consignment packages directly on the ground.
Do not expose consignment packages to the weather or directly to the sun.
Check the packaging every two months.
Warning
Verify that the direction of the flow in the line corresponds to the arrow indicated on the valve
body. Valves without the arrow are bi-directional.
See the actuator user manual for the actuator preparation.
Valve slinging
Figure no. 1

Pressure Seal Gate Valves -Style A-
Installation and Maintenance Instructions
Emerson reserves the right to change the contents without notice page 3
2.2 Installation Instructions
Gate valves are normally installed in horizontal pipe with vertical stem.
These valves can also be installed in vertical or horizontal pipe with stem other than vertical, but
this may require special construction depending on valve size, service condition, material and type
of operator.
For a correct operation, Sapag recommends that the valve shall be installed and oriented following
the indications of fig. 2.
This can help minimize any problem associated with solid particles present in the fluid that
otherwise could deposit in the lower part of the body and be obstacle to the wedge complete
closure.
Unless otherwise recommended by Sapag, the valve should be installed with the wedge in the
closed position, to ensure that the seat ring in the wedge is not damaged during installation.
Particular care should be taken with those valves equipped with ‘fail-open’ actuators.
For operating temperatures above 200°C (392°F) thermal insulation of the valve body is
recommended.
Handling and lifting of the valves during installation MUST be performed following the same criteria
and instructions described in previous points “1.2 Handling Requirements” and “1.3 Storage and
Preservation before Installation”.
Important
After the valves installation and before the line testing, it is recommended to perform an
accurate cleaning of the lines to eliminate dirt and any foreign objects that could seriously
jeopardize the tightness between seat/disc and the correct operation of the valve.
Buttweld Valves
Position the valve and check the alignment with the pipe, then proceed with welding, in
accordance with the applicable welding procedure.
Important
If piping system is pressurized with water for testing, and in case the piping system has been
shut down after testing for a long time, the following recommendations should be adopted.
a. Use corrosion inhibitor with water to pressurize the piping system
b. After testing, the piping system should be depressurized and the test water completely
drained.
2.3 Valve Verification before Start Up
1. Tighten the packing just enough to prevent stem leakage. Over-tightening will decrease packing
life and increase operating torque. The bolt torque figures for the packing bolts can be calculated
as indicated in Table I.
2. Check the operation of the valve by stroking it to “full open” and “full close”.
3. If the valve has been stored for a long time, check the bolt torque for bolting (pos. 31) in
accordance with table II.
2.4 Operations Instructions
1. Style A Series Gate Valves do not require special care to work properly.
The following instructions will help provide a satisfactory and long life service.
2. Make sure to perform periodic valve verification as described in paragraph 2.5.
3. In case of actuated valves always follow the specific instructions given by the actuator’s
manufacturer.
4. Never change the setting of torque and/or limit switches which have been carefully set during
the final test at Sapag workshop.
Figure no. 2
Installation positions
recommended
90° max.

3/8 18 24,5
1/2 37 50
5/8 74 100
3/4 125 170
7/8 207 280
1 310 420
1 1/8 443 600
1 1/4 627 850
1 3/8 811 1100
Pressure Seal Gate Valves -Style A-
Installation and Maintenance Instructions
Emerson reserves the right to change the contents without notice page 4
2.5 Periodic Valve Verification during Service
A - Normal Check
1. Verify monthly that there is no leakage from packing or in the body/bonnet area. If the leakage
has been detected from the packing, tighten nuts according to the procedure described in
Section 3.
If the leakage does not stop, follow the procedure for packing maintenance (3.1).
If the leakage has been detected from the body/bonnet, tighten the nuts (pos. 31) as indicated in
Table II.
If the leakage does not stop, follow the maintenance procedure for the replacement of the body/
bonnet gasket (3.2, 3.3).
2. Every 2 / 3 months, depending on operating frequency, verify the greasing of bearings and stem
thread.
3. For actuated valves, in addition to the above, please refer also to the warnings in the actuator
manual.
Troubleshooting Guide
Symptom
Stem packing leaking
Body-Bonnet leaking
Valve leaking
Jerky operation
Back seat leaking
Table I: Bolt Torque Figures for Packing Bolts
For System pressures < 2533 psi For System pressures ≥ 2533 psi
Torque (ft lbs) = (24.87) x (OD2 _ ID2) x (d) Torque (ft lbs) = (S.P./101.8) x (OD2 _ ID2) x (d)
Torque (Nm) = multiply Torque (ft lbs) x 1.3558
Where: OD = Stuffing Box Bore (ln.)
ID = Stem Diam (In.)
d = Gland Stud Diam (in.)
S.P. = System Pressure (psi)
This “Torque method” may result in more or less than 30% compression.
Important
To ensure tightness of Pressure Seal gasket,
pull up bolts must be tightened when valve is
under fully hydrostatic test pressure.
B - Preventive Actions
1. Every 3 months verify the tightness of gland bolts.
2. Every 6 months on motorized valves and every 8 months on hand operated valves, grease stem
and bearings.
3. Every 12 months check the travel of the gland follower, setting a new packing when the end of
the travel is approaching.
4. Every 4 years disassemble the critical service valves and/or actuated valves, verifying the sealing
surfaces and lap them again when necessary. Substitute the bonnet gasket and the packing,
grease the stem.
5. For the actuator, proceed as indicated in its maintenance manual.
Table II:
Bolt Torque to Ensure Tightness
of Pressure Seal Gasket
Position 31 for Gate Valves
Stud Torque ft.lbs. Torque Nm
Possible Cause
1. Gland flange nuts too loose
2. Packing damaged
1. Gasket bolting loose
(pos 31)
2. Gasket damage
1. Valve not fully closed
2. Debris trapped in valve
3. Sealing surface damaged
1. Packing is too tight
2. Air supply inadequate
(forpneumatic act.)
1. Back seat damage
Solution
1. Tighten gland flange nuts.
2. Replace packing
(SeeParagraph3.1)
1. Tighten bolting
(pos 31)
2. Replace the gasket
1. Close valve
2. Cycle and flush (with valve open)
to remove debris
3. Recondition the seat surface
1. Loosen gland nuts, cycle the
valve, retighten
2. Increase air supply pressure
1. Replace the back seat

Pressure Seal Gate Valves -Style A-
Installation and Maintenance Instructions
Emerson reserves the right to change the contents without notice page 5
Section 3 - Maintenance
The Style A Series Valves have been designed to require minimum maintenance.
This manual describes on site repairs as:
- Packing Replacement
- Body/Bonnet Gasket Replacement
All the other repairs should be performed by Sapag or Nominated Service Company.
3.1. Packing Maintenance
If leakage is observed through the packing, tighten the gland nuts slowly and evenly until the
leakage stops.
1. Open completely the valve up to the backseat position.
2. Remove the nuts (16) of the gland bolts (15)
3. Lift the gland flange (10) and the gland (9)
4. Remove the worm-out packing using a hooking wire
5. For a better tightness, proceed to an accurate cleaning of the stem and stuffing box and make
sure there are no scratches or signs of seizing
6. The repacking shall be carried out by placing one ring at a time around the stem, inside the
stuffing box and by making sure that they are correctly oriented. Press it into the bottom (refer
to Figure no. 3).
7. When the stuffing box is filled, replace the gland (9) and gland flange (10) in their original
position.
8. Tighten gland nuts in accordance with Table I (Bolt Torque figures for Packing Bolts).
9. Cycle the valve.
10. Pressurize the line.
11. If a leakage is detected, tighten the gland nuts slowly and evenly until the leakage stops.
3.2 Bonnet Gasket Replacement
1 = Braided graphite
2 = Die formet graphite (5 or 6 ring)
3 = Metal ring
Figure no. 3
Figure no. 4
Caution
Do not over-tighten packing gland nuts. Over-tightening will increase the torque required to
operate the valve.
When tightening the gland nut, use half-turn increments until leakage has stopped.
Warning
Before starting any maintenance, depressurize, drain and vent the line; check that the valves
are not in temperature; disconnect any electrical power supply.
Failure to do so may cause serious personal injury and/or equipment damage.
Warning
Before starting any maintenance, depressurize, drain and vent the line; check that the valves
are not in temperature; disconnect any electrical power supply.
Failure to do so may cause serious personal injury and/or equipment damage.
Please refer to Figure no. 4.
To replace the packing proceed as follows:

Pressure Seal Gate Valves -Style A-
Installation and Maintenance Instructions
Emerson reserves the right to change the contents without notice page 6
Section 4 - Valve Removal
If the valve needs to be removed from the line for some extraordinary reason, the user should
ensure the following:
1. The valve is depressurized, drained and vent.
2. The pipe shall be cut as far away from the valve as possible.
Section 5 - Greases and Special Tools
5.1 Greases
To lubricate the bearings on manual and gearbox operated valves, we suggest to use the grease
AGIP GRMUEP2 or an equivalent product, as showed in the following table:
Table III: Grease and Lubricant List
Manufacturer Grease
AGIP GRMUEP2
API PGX2
BP GREASE LTX2
ESSO BEACON 2
FINA FINAGREASE HP FINAGREASE EPL2
MOBIL MOBILUX EP2
Q8 REMBRANDT EP2
SHELL ALVANIA R2 SUPERGREASE A
TEXACO MULTIFAK EP2 GREASE L2
TOTAL MULTIS EP2 MULTIS 2
VISCOL SIGNAL ROLSFER 2
STATOIL UHIWAYLI LI G2
5.2 Special Tools
No special tool required for the Maintenance Operation described in this Manual.
Lifting lugs
for DN = 6”
For DN = 4” For DN = 3”
Please refer to Figure no. 5.
1. Unscrew the body bonnet nuts (pos.12) and the gland nuts (pos.16)
2. Lift up the yoke (pos.24) operating by the handwheel or gearbox handwheel
3. When the stem nut is free from the stem threads, lift up the yoke.
4. Unscrew the nuts (pos.31).
5. Remove the retaining ring (pos.311).
6. Remove the segment rings, push them out from the body groove by using the body holes
placed radially on the top of the body.
7. Lift up the bonnet (pos.6) and pressure seal body gasket (pos.5). Make sure not to damage the
packing. We suggest to replace the packing when changing the body gasket.
8. Carefully clean all the gasket housing and lubricate with suitable grease.
9. Replace the body gasket.
10. Reassemble all parts following backwards the above mentioned steps.
Caution
The nuts (pos.31) need to be retightened
after valve first pressurization, as indicated
in Table II.
Fig. no. 5
For the lubrication of the stem thread, use the grease SIGNAL CEP 30 produced by Viscol. As an
alternative you can utilize:
- CEPLATTYN 300 produced by REINER-FUCHS
- GRAFLOSCON produced by KLUBER
You can also use a grease having more than 25% pure graphite content (carbon 98%) granulometry
5m, without any abrasive agent.
For the lubrication of the actuator, refer to the relevant manual.