Emerson CASH VALVE B-95 Manual

CASH VALVE™ TYPE B-95 PRESSURE REDUCING OR PRESSURE BUILD REGULATOR
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
Before installation, these instructions must be carefully read and understood.
DESCRIPTION
The Type B-95 is a fully automatic pressure
reducing valve designed to reduce a high inlet
pressure to a lower pressure and maintain the
lower pressure to reasonably close limits. Also
available in a cryogenic version, it is ideal for
use in the pressure build-up circuit, for either
liquid oil or gas service.
INSTALLATION INSTRUCTIONS
The Type B-95 regulator may be installed
in the horizontal positon with the spring
chamber up or down. For other installation
requirements, consult the factory. For ease
of operation and maintenance, it is suggested
that manual shutoff valves be installed
upstream and downstream from the valve.
Before installing the valve, all piping should be
thoroughly flushed out to remove any foreign
material. Install the valve with the inlet pipe
fitted to the inlet connection identified on the
valve body. Use a compatible sealant on the
male pipe threads and do not overtighten the
valve connections.
SPECIFICATION DATA
Service: Air, water, steam,
oil and other liquids.
also cryogenic liquids
and gases.
Sizes: ½,
3
/
4and 1"
(15, 20, 25 mm)
Connections: Threaded Female NPTF
inlet and outlet
Temperature Rating: -320 to 400°F
(-195 to 204°C),
depending on
construction.
Maximum
Inlet Pressure:
720 psig (49.6 bar) at
180°F (82°C)
400 psig (27.5 bar) at
-320 to 400°F
(-195 to 204°C)
Steel or stainless steel bodies and chambers,
stainless steel trim. Choice of metal, Teflon or
Buna-N seating. Buna-N diaphragm (limited to
180°F) or Stainless steel laminated diaphragms
(to 450°F). Cryogenic version incorporates
Stainless steel pressure spring, cap screws,
and adjusting screw and lock nut.
VCIOM-14989-EN 22/01© 2020 Emerson. All rights reserved.Emerson.com
WARNING
Failure to follow these instructions or to properly
install and maintain this equipment could result in
an explosion, fire and/or chemical contamination
causing property damage and personal injury
or death.
Cash Valve regulators must be installed, operated
and maintained in accordance with federal,
state and local codes, rules and regulations
and Emerson Process Management Regulator
Technologies, Inc. instructions.
If the regulator vents gas or a leak develops in
the system, service to the unit may be required.
Failure to correct trouble could result in a
hazardous condition.
Installation, operation and maintenance
procedures performed by unqualified personnel
may result in improper adjustment and unsafe
operation. Either condition may result in
equipment damage or personal injury. Only
a qualified person shall install or service the
Type B-95 regulator.
CALIFORNIA PROPOSITION 65 WARNING
This product can expose you to chemicals
including lead, which is known to the State of
California to cause cancer, birth defects or other
reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
INTRODUCTION
Scope of the Manual
This manual provides instructions for the
installation, adjustment, and maintenance for
the Type B95 pressure regulator.

2
CASH VALVE™ TYPE B-95 PRESSURE REDUCING OR PRESSURE BUILD REGULATOR
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
Refer to the Type B-95 regulator exploded view for
parts identification.
Servicing Diaphragm(s) and Pressure Spring
1. Loosen the lock nut and turn the adjusting
screw counterclockwise until the pressure
spring is no longer under tension. When
reassembling, run the adjusting screw down
until the lock nut almost touches the spring
chamber. This will give you approximately
the same set as before disassembly.
2. Remove the assembly screws securing
the spring chamber to the body. During
reassembly, tighten the screws evenly in
a star pattern. See chart below for torque
values.
3. Remove the spring chamber. Then remove
the spring button, pressure spring, and
pressure plate.
4. Remove the diaphragm(s) and diaphragm
gasket (a diaphragm gasket is only
present when construction calls for metal
diaphragms).
5. Remove the pusher post button. During
reassembly, ensure the pusher post button
is centered properly on the pusher post.
6. Inspect all parts for wear and damage and
replace if necessary. Reassemble parts
in reverse order. DO NOT OVERTIGHTEN.
Follow the Operation Instructions to reset
the delivery pressure.
CAUTION
Before attempting to replace any spare parts, be
sure to shut off all pressure connections to the
valve. With the valve closed, however, system
pressure could still be locked between the
shut-off valve and the inlet and/or outlet sides of
the relief valve. Before proceeding with the valve
service, be certain to relieve the pressure from
BOTH sides of the valve
Servicing the Cylinder, Piston, Strainer
Screen and Plug Gasket
1. Loosen the lock nut and turn the adjusting
screw counterclockwise until the pressure
spring is no longer under tension. When
reassembling, run the adjusting screw down
until the lock nut almost touches the spring
chamber. This will give you approximately
the same set as before disassembly.
2. Remove the bottom plug. Take care, as
the bottom plug is under slight tension as
a result of the piston spring acting against
the bottom plug. Remove the piston, piston
spring and strainer screen.
3. Thoroughly clean the strainer screen and
remove any debris from the valve body.
4. Remove the hexagon cylinder.
5. Inspect all parts for wear and damage. If
either the cylinder or piston need replacing,
it is necessary to replace both as both parts
wear equally.
6. Reassemble the valve in reverse order. DO
NOT OVERTIGHTEN. Follow the Operation
Instructions to reset the delivery pressure.
ASSEMBLY SCREW TORQUE VALUE (IN-LBS)
Valve SIze (in.) ½ ¾ 1
Metal Diaphragm 200 200 250
Rubber Diaphragm 150 200 200
MAINTENANCE INSTRUCTIONS
The following procedures are provided for
servicing the recommended spare parts for the
Type B-95 regulator. Repair parts can easily be
installed without removing the regulator from
the line.
OPERATION INSTRUCTIONS
Adjusting the Delivery Pressure
The regulator's delivery pressure setting is
adjusted by turning the adjusting screw (1)
at the top of the spring chamber (5) after
loosening the adjusting screw lock nut (2). To
increase delivery pressure, turn the adjusting
screw clockwise (into the spring chamber).
To decrease the delivery pressure, turn the
adjusting screw counterclockwise (out of the
spring chamber). After each adjustment, draw
flow downstream and close to check new
setting. Tighten the adjusting screw lock nut
after the adjustment has been made.

3
CASH VALVE™ TYPE B-95 PRESSURE REDUCING OR PRESSURE BUILD REGULATOR
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
AVAILABLE OPTIONS
Available with drilled and tapped spring
chamber and pressure screw cap for
differential service with Spring Chamber Style
selection D - w/ Pressure Screw Cap and
Differential Connection.
Item Qty Description Material
11Adjusting Screw SST
21Lock Nut SST
31Name Plate Aluminum
41Spring Chamber 316 SST/Steel
51Spring Button 316 SST
61Pressure Spring Steel
71Pressure Plate 316 SST
84Diaphragm 316 SST
91Gasket Aramid Fiber
10 6Screw SST
12 1Pusher Post
Button 316 SST
13 1Screen SST
14 1Cylinder SST
15 1Piston Sub - - - -
15a 1Pusher Post SST
15b 1Seat Disc PTFE/SST
15c 1Piston SST
16 1Piston Spring SST
17 1Body SST/Steel
18 1Gasket Aramid Fiber
19 1Bottom Plug 316 SST
20 1Adjusting Screw
Cap SST
21 1Cap Gasket PTFE
PARTS LIST

4
B
C
A
CASH VALVE™ TYPE B-95 PRESSURE REDUCING OR PRESSURE BUILD REGULATOR
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
REDUCED PRESSURE RANGES, psig
Body Trim Seat Diaphragm
Maximum Inlet
Pressure, psig
Maximum Inlet
Pressure, bar
Maximum Outlet
Pressure, psig
Maximum Outlet
Pressure, bar
Temperature
Range, °F
Temperature
Range, °C
Steel Stainless
steel
Metal
Buna-N
Teflon
Stainless steel
Buna-N
Stainless steel
400
720
400
27.5
49.6
27.5
250
4001
250
17.2
27.5
17.2
-20–400
-20–180
-20–350
-6–204
-6–82
-6–176
Stainless
steel
Stainless
steel
Metal
Buna-N
Teflon
Stainless steel
Buna-N
Stainless steel
400
720
400
27.5
49.6
27.5
250
4001
4001
17.2
27.5
27.5
-20–400
-20–180
-320–350
-6–204
-6–82
-195–176
NOTES
1. Stainless springs furnished for higher ranges and for all cryogenic valves.
2. Stainless steel construction only.
3. For steam service, we recommend a maximum differential pressure of 150 psi to prevent seat erosion.
1. Requires diaphragm spacer and modified pressure plate.
VCIOM-14989-EN © 2020, 2022 Emerson Electric Co. All rights reserved 01/22. Cash Valve is a mark owned by one of the companies in the Emerson Automation
Solutions business unit of Emerson Electric Co. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their
prospective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed
by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time
without notice.
Emerson Electric Co. does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of
any Emerson Electric Co. product remains solely with the purchaser.
Emerson.com
Size, in. Steel Spring Stainless Spring
½
2–30 10–30
10–50 20–75
30–125 25–125
50–150 100–200
- - - - 150–250
- - - - 250-400(2)
- - - - 200-600(2)
¾
2–20 10–30
10–35 20–70
30–75 50–150
50–110 100–225
105–150 150–250
1
2–20 10–35
10–45 20–60
20–60 50–100
55–100 100–250
90–150 200-400(2)
Body, in.
Dimensions, in. Ship. Wt.,
lbsA B C
½4½ 5
19
/
32 1
19
/
32 7½
¾5¼ 5
¾
1
15
/
32 8½
15⅞ 6
¾
1⅝ 13½
TRIM OPTIONS WITH PRESSURE AND TEMPERATURE LIMITS