Emerson Fisher FIELDVUE DVC6000f User manual

DVC6000f Digital Valve Controllers Instruction Manual
D103189X012
December 2009
FisherFIELDVUEDVC6000f
Digital Valve Controllers
This manual applies to:
Device Type 4602
Device Revision 2
Hardware Revision 8
Firmware Revision 2.0
DD Revision 2 and 3
Instrument Level FD, PD, AD
Standard Control (SC)
Fieldbus Control (FC)
Fieldbus Logic (FL)
Introduction and Specifications
Installation
Basic Setup
Detailed Setup
Calibration
Viewing Device Variables and Diagnostics
Maintenance and Troubleshooting
Parts
Principle of Operation
Loop Schematics / Nameplates
Using PlantWebAlerts
FOUNDATIONFieldbus Communication
Device Description (DD) Installation
Operating with a DeltaVSystem
Glossary
Index
1
2
3
4
5
6
7
8
A
B
C
D
E
F
G
Glossary
Index
www.Fisher.com

i
i
Transducer Block
Field Communicator Menu Tree
Top Level
Configure/Setup
Device Diagnostics
Device Variables
Basic Setup
Device Setup
Performance Tuner
Detailed Setup
Transducer Block Mode
Protection
Response Control
Alerts
Instrument
Valve and Actuator
MAI Channel Map
Alert Handling
Device Variables
All Block Modes
AO Control −Pre-Char
AO Control −Post-Char
DO Control
Input Characterization
:Travel/Pressure State
:PD Inside Status
Protection
Drive Signal
Temperature
Cycle Counter
Travel Accumulator
:Travel Count
Pressures
Response Control
Travel Tuning
Pressure Tuning
Travel Press Control
Input Characterization
Custom Characterization Table
Outblock Selection
Calibration
Auto Calibration
Manual Calibration
Relay
Travel Sensor
Supply Pressure
Pressure A
Pressure B
Valve and Actuator
Valve
Trim
Actuator
Reference
Instrument
Tag Description
Pressure Units
Temperature Units
Travel Units
Length Units
Area Units
Spring Rate Units
:Relay Type
:Zero Power Condition
:Maximum Supply Pressure
Calibration Person
Calibration Location
Calibration Date
:Last Calibration Type Valve
Valve Manufacturer
Valve Model Number
Valve Serial Number
Valve Style
:Valve Size
:Valve Class
:Rated Travel
:Actual Travel
:Shaft Stem Diameter
:Packing Type
:Inlet Pressure
:Outlet Pressure
Trim
:Seat Type
:Leak Class
:Port Diameter
:Port Type
:Flow Direction
:Push Down To
:Flow Tends To
:Unbalanced Area
Actuator
Actuator Manufacturer
Actuator Model Number
:Actuator Style
Actuator Serial Number
:Actuator Size
Actuator Fail Action
:Feedback Connection
:Travel Sensor Motion
:Lever Style
:Lever Arm Length
:Effective Area
:Air
:Upper Bench Set
:Lower Bench Set
:Nominal Supply Pressure
:Spring Rate
Reference
:Trim Style 1
:Trim Style 2
:Stroke Time Open
:Stroke Time Close
Travel Tuning
:Travel Tuning Set
Travel Proportional Gain
Travel Velocity Gain
:Travel MLFB Gain
:Travel Integral Enable
:Travel Integral Gain
:Travel Integral Dead Zone
:Travel Integral Limit Hi
:Travel Integral Limit Lo
Performance Tuner
Stabilize / Optimize
Pressure Tuning
:Pressure Tuning Set
:Pressure Proportional Gain
:Pressure MLFB Gain
:Pressure Integral Gain
:Pressure Integral Dead Zone
:Pressure Integral Limit Hi
:Pressure Integral Limit Lo
Travel Pressure Control
:Travel/Pressure State
:Travel/Pressure Select
Travel Deviation Pressure Fallback
Travel Cutoff Hi
Travel Cutoff Lo
:Pressure Cutoff Open
:Pressure Cutoff Closed
:Pressure Range Hi
:Pressure Range Lo
Device Record
:Maximum Recorded Temperature
:Maximum Recorded Temperature Time
:Minimum Recorded Temperature
:Minimum Recorded Temperature Time
:Maximum Recorded Supply Pressure
:Maximum Recorded Supply Pressure Time
:Minimum Recorded Supply Pressure
:Minimum Recorded Supply Pressure Time
AO Control −Pre-Char
:Setpoint
:Setpoint Status
:Travel (DeChar)
Alert Handling
PlantWeb Alert Simulate
Simulate Active Alerts
PlantWeb Alert Handling
Simulate Active Alarms
Failed Active
Maint Active
Advise Active
MAI Channel Map
:MAI Channel 1
:MAI Channel 2
:MAI Channel 3
:MAI Channel 4
:MAI Channel 5
:MAI Channel 6
:MAI Channel 7
:MAI Channel 8
PlantWeb Alert Handling
PlantWeb Alerts Set PV Status
Block Error Reporting
Configure/Setup
Basic Setup
Detailed Setup
Calibration
Alerts
Elect Alerts
Configuration Alerts
Sensor Alerts
Environment Alerts
Travel Alerts
Prox Alerts
Travel History Alerts
Performance Alerts
PlantWeb Alert Enable
PlantWeb Alert Reporting
ALERTS MENU
Device Diagnostics
Active PlantWeb Alerts
Alert Conditions
Status
Device Record
Stroke Valve
Trend
Status
Self Test Status
Block Error
Self Test Status
Integrator Suspended
Integrator Limited Lo
Integrator Limited Hi
Travel Sensor Span Error
MLFB Error
Travel Sensor Hi Error
Travel Sensor Lo Error
Pressure B Sensor Failure
Pressure A Sensor Failure
Supply Sensor Failure
IOP Failure
Drive Current Alert
Simulate Jumper ON
Block Error
Block Configuration Error
Simulate Active
Lost Static Data
Device Needs Maintenance Now
Out of Service
Pressures
:Supply
:Pressure A
:Pressure B
:A Minus B
AO Control −Post-Char
:Travel Target
:Travel
:Travel Status
DO Control
:Setpoint(D)
:Travel(D)
ON FACING
PAGE

ii ii
PlantWeb Alert Enable
Failed Enable
Maintenance Enable
Advise Enable
Prox Alerts
:Travel
Travel Open
Travel Closed
Proximity
PlantWeb Alert
Reporting
Failed Suppress
Maintenance Suppress
Advise Suppress
Drive Current
Drive Current
:Drive Current Alert
:Drive Current Alert Enable
:Drive Current Shutdown
:Drive Current Manual Recovery
:Drive Current Alert Point
:Drive Current Alert Time
Alerts
Elect Alerts
Configuration Alerts
Sensor Alerts
Environment Alerts
Travel Alerts
Prox Alerts
Travel History Alerts
Performance Alerts
PlantWeb Alert Enable
PlantWeb Alert Reporting
Output Block Timeout
:Output Block Timeout Alert
:Output Block Timeout Alert Enable
:Output Block Timeout Shutdown
:Output Block Timeout Manual Recovery
:Output Block Timeout
Processor Impaired
:Program Memory Alert
:Program Memory Alert Enable
:Program Memory Shutdown
:Program Memory Manual Recovery
:Static Memory Alert
:Static Memory Alert Enable
:Static Memory Shutdown
:Static Memory Manual Recovery
:Processor Alert
:Processor Alert Enable
:I/O Processor Alert
:I/O Processor Alert Enable
:I/O Processor Shutdown
:I/O Processor Man Recovery
Elect Alerts
Drive Current
Drive Signal
Processor Impaired
Drive Signal
Drive Signal
:Drive Signal Alert
:Drive Signal Alert Enable
Configuration Alerts
Output Block Timeout
Blocks Set to Default
Alert Key
Blocks Set to Default
:Blocks Set to Defaults Alert
:Blocks Set to Defaults Alert Enable
Travel History Alerts
Cycle Counter
Travel Accumulator
Performance Alerts
:PD Inside Status
:PD Run
Performance Critical
Performance Reduced
Performance Information
Sensor Alerts
Travel Sensor
Pressure Sensors
Pressure Fallback
Temperature Sensor
Travel Sensor
:Travel Sensor Alert
:Travel Sensor Alert Enable
:Travel Sensor Shutdown
:Travel Sensor Manual Recovery
Pressure Sensors
:Pressure A Sensor Alert
:Pressure A Sensor Alert Enable
:Pressure A Sensor Shutdown
:Pressure A Sensor Manual Recovery
:Pressure B Sensor Alert
:Pressure B Sensor Alert Enable
:Supply Pressure Sensor Alert
:Supply Pressure Sensor Alert Enable
Pressure Fallback
:Pressure Fallback Alert
:Pressure Fallback Alert Enable
Temperature Sensor
:Temperature Sensor Alert
:Temperature Sensor Alert Enable
Supply Pressure
:Supply
:Supply Pressure Hi Alert
:Supply Pressure Hi Alert Enable
Supply Pressure Hi Alert Point
:Supply Pressure Lo Alert
:Supply Pressure Lo Alert Enable
:Supply Pressure Lo Alert Point
Environment Alerts
Supply Pressure
Temperature Limit
Temperature Limit
Temperature
:Temperature Hi Alert
:Temperature Hi Alert Enable
Temperature Hi Alert Point
:Temperature Lo Alert
:Temperature Lo Alert Enable
:Temperature Lo Alert Point
Travel Alerts
:Travel Target
:Travel
Travel Deviation
Travel Limit
Travel Hi/Lo
Travel Deviation
Travel Deviation
:Travel Deviation Alert
:Travel Deviation Alert Enable
:Travel Deviation Alert Point
:Travel Deviation Time
:Travel Deviation Deadband
Travel Limit
:Travel Hi Hi Alert
:Travel Hi Hi Alert Enable
:Travel Hi Hi Alert Point
:Travel Hi Hi Deadband
:Travel Lo Lo Alert
:Travel Lo Lo Alert Enable
:Travel Lo Lo Alert Point
:Travel Lo Lo Deadband
Travel Hi/Lo
:Travel Hi Alert
:Travel Hi Alert Enable
:Travel Hi Alert Point
:Travel Hi Deadband
:Travel Lo Alert
:Travel Lo Alert Enable
:Travel Lo Alert Point
:Travel Lo Deadband
Travel Open
Travel Open Alert
Travel Open Alert Enable
:Travel Open Alert Point
:Travel Open Deadband
Travel Closed
:Travel Closed Alert
:Travel Closed Alert Enable
:Travel Closed Alert Point
:Travel Closed Deadband
Proximity
:Proximity Hi Hi Alert
:Proximity Hi Hi Alert Enable
:Proximity Hi Alert
:Proximity Hi Alert Enable
:Proximity Lo Alert
:Proximity Lo Alert Enable
:Proximity Lo Lo Alert
:Proximity Lo Lo Alert Enable
Cycle Counter
Cycle Counter
:Cycle Counter Alert
:Cycle Counter Alert Enable
:Cycle Counter Alert Point
:Cycle Counter Deadband
Travel Accumulator
Travel Accumulator
:Travel Accumulator Alert
:Travel Accumulator Alert Enable
:Travel Accumulator Alert Point
:Travel Accumulator Deadband
Performance Critical
Performance Critical Alert
Performance Critical Alert Enable
Performance Reduced
Performance Reduced Alert
Performance Reduced Alert Enable
Performance Information
Performance Information Alert
Performance Information Alert Enable
ALERTS MENU
ALERTS MENU

iii
iii
TransducerBlock (TB) Menu Structure
PARAMETER LABEL MENU STRUCTURE
A Minus B TB > Device Variables > Pressures > A Minus B
Actual Travel TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Actual Travel
Actuator Fail Action TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Actuator Fail Action
Actuator Manufacturer TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Actuator Manufacturer
Actuator Model Number TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Actuator Model Number
Actuator Serial Number TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Actuator Serial Number
Actuator Size TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Actuator Size
Actuator Style TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Actuator Style
Advise Active TB > Configure/Setup> Detailed Setup > Alert Handling > Simulate Active Alerts > Advise Active
Advise Enable TB > Configure/Setup> Detailed Setup > Alerts > PlantWeb Alert Enable > Advise Enable
Advise Suppress TB > Configure/Setup> Detailed Setup > Alerts > PlantWeb Alert Reporting > Advise Suppress
Air TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Air
Alert Conditions TB > Device Diagnostics > Alert Conditions
Alert Key TB > Configure/Setup> Detailed Setup > Alerts > Configuration Alerts > Alert Key
Area Units TB > Configure/Setup> Detailed Setup > Instrument > Area Units
Block Configuration Error TB > Device Diagnostics > Status > Block Error > Block Error.Block Configuration Error
Blocks Set to Defaults Alert TB > Configure/Setup> Detailed Setup > Alerts > Configuration Alerts > Blocks Set to Defaults > Elect Active.Block Set to
Defaults Alert
Blocks Set to Defaults Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Configuration Alerts > Blocks Set to Defaults > Elect Enable.Block Set to Defaults Alert Enable
Calibration Date TB > Configure/Setup> Detailed Setup > Instrument > Calibration Date
Calibration Location TB > Configure/Setup> Detailed Setup > Instrument > Calibration Location
Calibration Person TB > Configure/Setup> Detailed Setup > Instrument > Calibration Person
Custom Characterization Table TB > Configure/Setup> Detailed Setup > Response Control >Custom Characterization Table
Cycle Counter TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Cycle Counter
TB > Device Variables > Cycle Counter
Cycle Counter Alert TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Travel History Active.Cycle Counter
Alert
Cycle Counter Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Travel History Enable.Cycle Counter
Alert Enable
Cycle Counter Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Cycle Counter Alert Point
Cycle Counter Deadband TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Cycle Counter Deadband
Device Needs Maintenance
Now TB > Device Diagnostics > Status > Block Error > Block Error.Device Needs Maintenance Now
Drive Current TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current
Drive Current Alert TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Drive Current Alert
TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Current > Elect Active.Drive Current Alert
Drive Current Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Current > Elect Enable.Drive Current Alert Enable
Drive Current Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current Alert Point
Drive Current Alert Time TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current Alert Time
Drive Current Manual Recovery TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Current > Shutdown Recovery.Drive Current Manual
Recovery
Drive Current Shutdown TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Current > Shutdown Trigger.Drive Current Shutdown
Drive Signal TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Signal > Drive Signal
TB > Device Variables > Drive Signal
Drive Signal Alert TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Signal > Elect Active.Drive Signal Alert
Drive Signal Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Drive Signal > Elect Enable.Drive Signal Alert Enable
Effective Area TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Effective Area
Failed Active TB > Configure/Setup> Detailed Setup > Alert Handling > Simulate Active Alerts > Failed Active
Failed Enable TB > Configure/Setup> Detailed Setup > Alerts > PlantWeb Alert Enable > Failed Enable
Failed Suppress TB > Configure/Setup> Detailed Setup > Alerts > PlantWeb Alert Reporting > Failed Suppress
Feedback Connection TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Feedback Connection
Flow Direction TB > Configure/Setup> Detailed Setup > Valve and Actuator > Trim > Flow Direction
Flow Tends To TB > Configure/Setup> Detailed Setup > Valve and Actuator > Trim > Flow Tends To
I/O Processor Alert TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Elect Active.I/O Processor Alert
I/O Processor Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Elect Enable.I/O Processor Alert Enable
−Continued−

iv iv
Transducer Block (TB) Menu Structure (Continued)
PARAMETER LABEL MENU STRUCTURE
I/O Processor Man Recovery TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Shutdown Recovery.I/O Processor Man
Recovery
I/O Processor Shutdown TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Shutdown Trigger.I/O Processor
Shutdown
Inlet Pressure TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Inlet Pressure
Input Characterization TB > Configure/Setup> Detailed Setup > Response Control > Input Characterization
TB > Device Variables > Input Characterization
Integrator Limited Hi TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Integrator Limited Hi
Integrator Limited Lo TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Integrator Limited Lo
Integrator Suspended TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Integrator Suspended
IOP Failure TB > Device Diagnostics > Status > Self Test Status > Self Test Status.IOP Failure
Last Calibration Type TB > Configure/Setup> Detailed Setup > Instrument > Last Calibration Type
Leak Class TB > Configure/Setup> Detailed Setup > Valve and Actuator > Trim > Leak Class
Length Units TB > Configure/Setup> Detailed Setup > Instrument > Length Units
Lever Arm Length TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Lever Arm Length
Lever Style TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Lever Style
Lost Static Data TB > Device Diagnostics > Status > Block Error > Block Error.Lost Static Data
Lower Bench Set TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Lower Bench Set
MAI Channel 1 TB > Configure/Setup> Detailed Setup > MAI Channel Map > MAI Channel 1
MAI Channel 2 TB > Configure/Setup> Detailed Setup > MAI Channel Map > MAI Channel 2
MAI Channel 3 TB > Configure/Setup> Detailed Setup > MAI Channel Map > MAI Channel 3
MAI Channel 4 TB > Configure/Setup> Detailed Setup > MAI Channel Map > MAI Channel 4
MAI Channel 5 TB > Configure/Setup> Detailed Setup > MAI Channel Map > MAI Channel 5
MAI Channel 6 TB > Configure/Setup> Detailed Setup > MAI Channel Map > MAI Channel 6
MAI Channel 7 TB > Configure/Setup> Detailed Setup > MAI Channel Map > MAI Channel 7
MAI Channel 8 TB > Configure/Setup> Detailed Setup > MAI Channel Map > MAI Channel 8
Maint Active TB > Configure/Setup> Detailed Setup > Alert Handling > Simulate Active Alerts > Maint Active
Maintenance Enable TB > Configure/Setup> Detailed Setup > Alerts > PlantWeb Alert Enable > Maintenance Enable
Maintenance Suppress TB > Configure/Setup> Detailed Setup > Alerts > PlantWeb Alert Reporting > Maintenance Suppress
Maximum Recorded Supply
Pressure TB > Device Diagnostics > Device Record > Maximum Recorded Supply Pressure
Maximum Recorded Supply
Pressure Time TB > Device Diagnostics > Device Record > Maximum Recorded Supply Pressure Time
Maximum Recorded
Temperature TB > Device Diagnostics > Device Record > Maximum Recorded Temperature
Maximum Recorded
Temperature Time TB > Device Diagnostics > Device Record > Maximum Recorded Temperature Time
Maximum Supply Pressure TB > Configure/Setup> Detailed Setup > Instrument > Maximum Supply Pressure
Minimum Recorded Supply
Pressure TB > Device Diagnostics > Device Record > Minimum Recorded Supply Pressure
Minimum Recorded Supply
Pressure Time TB > Device Diagnostics > Device Record > Minimum Recorded Supply Pressure Time
Minimum Recorded
Temperature TB > Device Diagnostics > Device Record > Minimum Recorded Temperature
Minimum Recorded
Temperature Time TB > Device Diagnostics > Device Record > Minimum Recorded Temperature Time
MLFB Error TB > Device Diagnostics > Status > Self Test Status > Self Test Status.MLFB Error
Nominal Supply Pressure TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Nominal Supply Pressure
Out of Service TB > Device Diagnostics > Status > Block Error > Block Error.Out of Service
Outlet Pressure TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Outlet Pressure
Outblock Selection TB > Configure/Setup> Detailed Setup > Response Control > Outblock Selection
Output Block Timeout TB > Configure/Setup> Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout
Output Block Timeout Alert TB > Configure/Setup> Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout> Elect Active.Output Block
Timeout Alert
Output Block Timeout Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout> Elect Active.Output Block Timeout Alert Enable
Output Block Timeout Manual
Recovery TB > Configure/Setup> Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout> Shutdown Recovery.Output Block Timeout Manual Recovery
−Continued−

v
v
Transducer Block (TB) Menu Structure (Continued)
PARAMETER LABEL MENU STRUCTURE
Output Block Timeout
Shutdown TB > Configure/Setup> Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout> Shutdown Recovery.Output Block Timeout Manual Recovery
Packing Type TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Packing Type
PD Inside Status TB > Configure/Setup> Device Variables > PD Inside Status
PD Run TB > Configure/Setup> Detailed Setup > Alerts > Performance Alerts > PD Run
Performance Critical Alert TB > Configure/Setup> Detailed Setup > Alerts > Performance Alerts > Performance Active.Performance Critical Alert
Performance Critical Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Performance Alerts > Performance Enable.Performance Critical Alert Enable
Performance Information Alert TB > Configure/Setup> Detailed Setup > Alerts > Performance Alerts > Performance Active.Peformance Information Alert
Performance Information Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Performance Alerts > Performance Enable.Peformance Information Alert Enable
Performance Reduced Alert TB > Configure/Setup> Detailed Setup > Alerts > Performance Alerts > Performance Active.Peformance Reduced Alert
Performance Reduced Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Performance Alerts > Performance Enable.Peformance Reduced Alert Enable
Performance Tuner TB > Configure/Setup> Basic Setup > Performance Tuner
TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning > Performance Tuner
PlantWeb Alert Simulate TB > Configure/Setup> Detailed Setup > Alert Handling > PlantWeb Alert Simulate
Port Diameter TB > Configure/Setup> Detailed Setup > Valve and Actuator > Trim > Port Diameter
Port Type TB > Configure/Setup> Detailed Setup > Valve and Actuator > Trim > Port Type
Pressure A TB > Device Variables > Pressures > Pressure A
Pressure A Sensor Alert TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Sensor Active.Pressure A Sensor Alert
Pressure A Sensor Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Sensor Enable.Pressure A Sensor Alert
Enable
Pressure A Sensor Failure TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Pressure A Sensor Error
Pressure A Sensor Manual
Recovery TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Shutdown Recovery.Pressure A Sensor Manual Recovery
Pressure A Sensor Shutdown TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Shutdown Trigger.Pressure A Sensor
Shutdown
Pressure B TB > Device Variables > Pressures > Pressure B
Pressure B Sensor Alert TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Sensor Active.Pressure B Sensor Alert
Pressure B Sensor Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Sensor Enable.Pressure B Sensor Alert
Enable
Pressure B Sensor Failure TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Pressure B Sensor Error
Pressure Cutoff Closed TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Pressure Cutoff Closed
Pressure Cutoff Open TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Pressure Cutoff Open
Pressure Fallback Alert TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Fallback > Sensor Active.Pressure Fallback Alert
Pressure Fallback Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Fallback > Sensor Enable.Pressure Fallback Alert
Enable
Pressure Integral Dead Zone TB > Configure/Setup> Detailed Setup > Response Control > Pressure Tuning> Pressure Integral Dead Zone
Pressure Integral Gain TB > Configure/Setup> Detailed Setup > Response Control > Pressure Tuning> Pressure Integral Gain
Pressure Integral Limit Hi TB > Configure/Setup> Detailed Setup > Response Control > Pressure Tuning> Pressure Integral Limit Hi
Pressure Integral Limit Lo TB > Configure/Setup> Detailed Setup > Response Control > Pressure Tuning> Pressure Integral Limit Lo
Pressure MLFB Gain TB > Configure/Setup> Detailed Setup > Response Control > Pressure Tuning> Pressure MLFB Gain
Pressure Proportional Gain TB > Configure/Setup> Detailed Setup > Response Control > Pressure Tuning> Pressure Proportional Gain
Pressure Range Hi TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Pressure Range Hi
Pressure Range Lo TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Pressure Range Lo
Pressure Tuning Set TB > Configure/Setup> Detailed Setup > Response Control > Pressure Tuning> Pressure Tuning Set
Pressure Units TB > Configure/Setup> Detailed Setup > Instrument > Pressure Units
Processor Alert TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Elect Active.Processor Alert
Processor Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Elect Enable.Processor Alert Enable
Program Memory Alert TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Elect Active.Program Memory Alert
Program Memory Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Elect Enable.Program Memory Alert
Enable
Program Memory Manual
Recovery TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Shutdown Recovery.Program Memory Manual Recovery
Program Memory Shutdown TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Shutdown Trigger.Program Memory
Shutdown
Protection TB > Device Variables > Protection
−Continued−

vi vi
Transducer Block (TB) Menu Structure (Continued)
PARAMETER LABEL MENU STRUCTURE
Proximity Hi Alert TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Active.Proximity Hi Alert
Proximity Hi Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Enable.Proximity Hi Alert Enable
Proximity Hi Hi Alert TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Active.Proximity Hi Hi Alert
Proximity Hi Hi Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Enable.Proximity Hi Hi Alert Enable
Proximity Lo Alert TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Active.Proximity Lo Alert
Proximity Lo Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Enable.Proximity Lo Alert Enable
Proximity Lo Lo Alert TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Active.Proximity Lo Lo Alert
Proximity Lo Lo Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Enable.Proximity Lo Lo Alert Enable
Push Down To TB > Configure/Setup> Detailed Setup > Valve and Actuator > Trim > Push Down To
Rated Travel TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Rated Travel
Relay Type TB > Configure/Setup> Detailed Setup > Instrument > Relay Type
Seat Type TB > Configure/Setup> Detailed Setup > Valve and Actuator > Trim > Seat Type
Setpoint TB > Device Variables > AO Control-Pre-Char > Setpoint
Setpoint Status TB > Device Variables > AO Control-Pre-Char > Setpoint Status
Setpoint(D) TB > Device Variables > DO Control > Setpoint(D)
Shaft Stem Diameter TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Shaft Stem Diameter
Simulate Active TB > Device Diagnostics > Status > Block Error > Block Error.Simulate Active
Simulate Jumper ON TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Simulate Jumper ON
Spring Rate TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Spring Rate
Spring Rate Units TB > Configure/Setup> Detailed Setup > Instrument > Spring Rate Units
Static Memory Alert TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Elect Active.Static Memory Alert
Static Memory Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Elect Enable.Static Memory Alert Enable
Static Memory Manual
Recovery TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Shutdown Recovery.Static Memory Manual Recovery
Static Memory Shutdown TB > Configure/Setup> Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Shutdown Trigger.Static Memory
Shutdown
Stroke Time Close TB > Configure/Setup> Detailed Setup > Valve and Actuator > Reference > Stroke Time Close
Stroke Time Open TB > Configure/Setup> Detailed Setup > Valve and Actuator > Reference > Stroke Time Open
Supply TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply
TB > Device Variables > Pressures > Supply
Supply Pressure Hi Alert TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Environment Active.Supply Pressure
Hi Alert
Supply Pressure Hi Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Environment Enable.Supply Pressure
Hi Alert Enable
Supply Pressure Hi Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply Pressure Hi Alert Point
Supply Pressure Lo Alert TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Environment Active.Supply Pressure
Lo Alert
Supply Pressure Lo Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Environment Enable.Supply Pressure Lo Alert Enable
Supply Pressure Lo Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply Pressure Lo Alert Point
Supply Pressure Sensor Alert TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Sensor Active. Supply Pressure Sensor
Alert
Supply Pressure Sensor Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Sensor Enable. Supply Pressure Sensor Alert Enable
Supply Sensor Failure TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Supply Sensor Failure
Tag Description TB > Configure/Setup> Detailed Setup > Instrument > Tag Description
Temperature TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature
Temperature Hi Alert TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Environment Active.Temperature Hi
Alert
Temperature Hi Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Environment Enable.Temperature
Hi Alert Enable
Temperature Hi Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature Hi Alert Point
Temperature Lo Alert TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Environment Active.Temperature Lo
Alert
Temperature Lo Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Environment Enable.Temperature
Lo Alert Enable
Temperature Lo Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature Lo Alert Point
Temperature Sensor Alert TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Temperature Sensor > Sensor Active. Temperature Sensor
Alert
−Continued−

vii
vii
Transducer Block (TB) Menu Structure (Continued)
PARAMETER LABEL MENU STRUCTURE
Temperature Sensor Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Temperature Sensors > Sensor Enable. Temperature Sensor Alert Enable
Temperature Units TB > Configure/Setup> Detailed Setup > Instrument > Temperature Units
Travel TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel
Travel (DeChar) TB > Device Variables > AO Control-Pre-Char > Travel(DeChar)
Travel Accumulator TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel Accumulator
TB > Device Variables > Travel Accumulator
Travel Accumulator Alert TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel History Active.Travel
Accumulator Alert
Travel Accumulator Alert
Enable TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel History Enable.Travel Accumulator Alert Enable
Travel Accumulator Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel Accumulator Alert Point
Travel Accumulator Deadband TB > Configure/Setup> Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel Accumulator Deadband
Travel Closed Alert TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel Closed > Proximity Active.Travel Closed Alert
Travel Closed Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel Closed > Proximity Enabled.Travel Closed Alert Enable
Travel Closed Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel Closed > Travel Closed Alert Point
Travel Closed Deadband TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel Closed > Travel Closed Deadband
Travel Count TB > Device Variables> Travel Count
Travel Cutoff Hi TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Travel Cutoff Hi
Travel Cutoff Lo TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Travel Cutoff Lo
Travel Deviation TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation
Travel Deviation Alert TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Active.Travel Deviation Alert
Travel Deviation Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Enable.Travel Deviation Alert Enable
Travel Deviation Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation Alert Point
Travel Deviation Deadband TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation Deadband
Travel Deviation Pressure
Fallback TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Travel Deviation Pressure Fallback
Travel Deviation Time TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation Time
Travel Hi Alert TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Active.Travel Hi Alert
Travel Hi Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Enable.Travel Hi Alert Enable
Travel Hi Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Hi Alert Point
Travel Hi Deadband TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Hi Deadband
Travel Hi Hi Alert TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Active.Travel Hi Hi Alert
Travel Hi Hi Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Enable.Travel Hi Hi Alert Enable
Travel Hi Hi Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Hi Hi Alert Point
Travel Hi Hi Deadband TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Hi Hi Deadband
Travel Integral Dead Zone TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning > Travel Integral Dead Zone
Travel Integral Enable TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning> Travel Integral Enable
Travel Integral Gain TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning> Travel Integral Gain
Travel Integral Limit Hi TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning > Travel Integral Limit Hi
Travel Integral Limit Lo TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning> Travel Integral Limit Lo
Travel Lo Alert TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Active.Travel Lo Alert
Travel Lo Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Enable.Travel Lo Alert Enable
Travel Lo Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Lo Alert Point
Travel Lo Deadband TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Lo Deadband
Travel Lo Lo Alert TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Active.Travel Lo Lo Alert
Travel Lo Lo Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Enable.Travel Lo Lo Alert Enable
Travel Lo Lo Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Lo Lo Alert Point
Travel Lo Lo Deadband TB > Configure/Setup> Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Lo Lo Deadband
Travel MLFB Gain TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning > Travel MLFB Gain
Travel Open Alert TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel Open > Proximity Active.Travel Open Alert
Travel Open Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel Open > Proximity Enabled.Travel Open Alert Enable
Travel Open Alert Point TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel Open > Travel Open Alert Point
Travel Open Deadband TB > Configure/Setup> Detailed Setup > Alerts > Prox Alerts > Travel Open > Travel Open Deadband
Travel Proportional Gain TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning> Travel Proportional Gain
Travel Sensor Alert TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Travel Sensor > Sensor Active.Travel Sensor Alert
Travel Sensor Alert Enable TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Travel Sensor > Sensor Enable.Travel Sensor Alert Enable
−Continued−

viii viii
Transducer Block (TB) Menu Structure (Continued)
PARAMETER LABEL MENU STRUCTURE
Travel Sensor Hi Error TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Travel Sensor Hi Error
Travel Sensor Lo Error TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Travel Sensor Lo Error
Travel Sensor Manual
Recovery TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Travel Sensor > Shutdown Recovery.Travel Sensor Manual Recovery
Travel Sensor Motion TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Travel Sensor Motion
Travel Sensor Shutdown TB > Configure/Setup> Detailed Setup > Alerts > Sensor Alerts > Travel Sensor > Shutdown Trigger.Travel Sensor Shutdown
Travel Sensor Span Error TB > Device Diagnostics > Status > Self Test Status > Self Test Status.Travel Sensor Span Error
Travel Status TB > Device Variables > AO Control-Post-Char > Travel Status
Travel Tuning Set TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning> Travel Tuning Set
Travel Units TB > Configure/Setup> Detailed Setup > Instrument > Travel Units
Travel Velocity Gain TB > Configure/Setup> Detailed Setup > Response Control > Travel Tuning > Travel Velocity Gain
Travel(D) TB > Device Variables > DO Control > Travel(D)
Travel/Pressure Select TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Travel/Pressure Select
Travel/Pressure State TB > Configure/Setup> Detailed Setup > Response Control > Travel Pressure Control > Travel/Pressure State
TB > Device Variables > Travel/Pressure State
Trend TB > Device Diagnostics > Trend
Trim Style 1 TB > Configure/Setup> Detailed Setup > Valve and Actuator > Reference > Trim Style 1
Trim Style 2 TB > Configure/Setup> Detailed Setup > Valve and Actuator > Reference > Trim Style 2
Unbalanced Area TB > Configure/Setup> Detailed Setup > Valve and Actuator > Trim > Unbalanced Area
Upper Bench Set TB > Configure/Setup> Detailed Setup > Valve and Actuator > Actuator > Upper Bench Set
Valve Class TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Valve Class
Valve Manufacturer TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Valve Manufacturer
Valve Model Number TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Valve Model Number
Valve Serial Number TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Valve Serial Number
Valve Size TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Valve Size
Valve Style TB > Configure/Setup> Detailed Setup > Valve and Actuator > Valve > Valve Style
Zero Power Condition TB > Configure/Setup> Detailed Setup > Instrument > Zero Power Condition

ix
ix
Resource Block
Field Communicator Menu Tree
Top Level
Configure/Setup
Device Diagnostics
Device Variables
Device Diagnostics
Resource Block Error
Device State
Write Lock
Block Alarm
Maintenance
Alarm Handling
Alert Key
Confirm Time
Limit Notify
Maximum Notify
Block Alm Disabled
Block Alarm Auto Acknowledge
Disc Alm Disabled
Discrete Alarm Auto Acknowlege
Write Lock
Write Lock
Write Priority
Comm Timeout
Shed Remote Cascade
Shed Remote Out
Options
Diagnostic Options
Function Block Options
Miscellaneous Options
Features Available
Features Selected
Function Block Options
AO
DO
AI
DI
PID
IS
OS
MAI
Miscellaneous Options
Firmware Download
Travel Control Capable
Pressure Control Capable
Pressure Fallback Capable
Features Available
Reports
Fault State
Soft W Lock
Multi-bit Alarm (Bit-Alarm) Support
Features Selected
Reports
Fault State
Soft W Lock
Multi-bit Alarm (Bit-Alarm) Support
Identification
Device ID
Electronics Serial Number
Factory Serial Number
Field Serial Number
Tag Description
Strategy
Manufacturer
Device Type
Diagnostics Options
Version
Device Revision
Firmware Revision
Standby Firmware Revision
Hardware Rev
ITK Version
Configure/Setup
Resource Block Mode
Write Lock
Comm Timeout
Options
Alarm Handling
Identification
Version
Resource Block Error
Other
Block Configuration Error
Simulate Active
Device Needs Maintenance Soon
Memory Failure
Lost Static Data
Lost NV Data
Device Needs Maintenance Now
Power Up
Out of Service
Write Lock
Write Alarm Alarm State
Write Lock
Block Alarm
Block Alarm Alarm State
Block Alarm Unacknowledged
Function
Block Options
AO
DO
AI
DI
PID
IS
OS
MAI
Instrument
Identification
Version
Identification
Device ID
Electronics Serial Number
Factory Serial Number
Field Serial Number
Tag Description
Strategy
Manufacturer
Device Type
Version
Device Revision
Firwmare Revision
Standby Firmware Revision
Hardware Rev
ITK Version
Options
Diagnostics Options
Function Block Options
Miscellaneous Options
Features Available
Features Available
Reports
Fault State
Soft W Lock
Multi-bit Alarm (Bit-Alarm) Support
Device Variables
Instrument
Options
DD Information
Miscellaneous Options
Firmware Download
Travel Control Capable
Pressure Control Capable
Pressure Fallback Capable
Maintenance
Restart Actions
Fault State
Set Fault State
Clear Fault State

xx
ResourceBlock (RB) Menu Structure
PARAMETER LABEL MENU STRUCTURE
Alert Key RB > Configure/Setup> Alarm Handling > Alert Key
Block Alarm: Alarm State RB > Device Diagnostics > Block Alarm > Block Alarm: Alarm State
Block Alarm: Unacknowledged RB > Device Diagnostics > Block Alarm > Block Alarm: Unacknowledge
Block Alarm Disabled RB > Configure/Setup> Alarm Handling > Alarm Summary:Disabled.Block Alarm Disabled
Block Alarm Automatically
Acknowledge RB > Configure/Setup> Alarm Handling > Acknowledge Option.Block Alarm Automatically Acknowledge
Confirm Time RB > Configure/Setup> Alarm Handling > Confirm Time
DD Information RB > Device Variables > DD information
Device ID RB > Configure/Setup> Identification> Device ID or RB > Device Variables > Instrument > Identification > Device ID
Device Revision RB > Configure/Setup> Version > Device Revision or RB > Device Variables > Instrument > Version > Device Revision
Device State RB > Display > Resource Status > Device State
RB > Device Diagnostics > Device State
Device Type RB > Configure/Setup> Identification> Device Type or RB > Device Variables > Instrument > Identification> Device Type
Diagnostics Options RB > Configure/Setup> Options > Diagnostics Options
Discrete Alarm Disabled RB > Configure/Setup> Alarm Handling > Alarm Summary:Disabled.Discrete Alarm Disabled
Discrete Alarm Automatically
Acknowledge RB > Configure/Setup> Alarm Handling > Acknowledge Option.Discrete Alarm Automatically Acknowledge
Electronics Serial Number RB > Configure/Setup> Identification> Elect S/N or RB > Device Variables > Instrument > Identification> Electronics Serial
Number
Factory Serial Number RB > Configure/Setup> Identification> Factory S/N or RB > Device Variables > Instrument > Identification> Factory Serial
Number
Fault State RB > Device Diagnostics > Maintenance> Fault State
Features Available RB > Configure/Setup> Options > Features Available or RB > Device Variables > Options > Features Available
Features Selected RB > Configure/Setup>Options > Features Selected
Field Serial Number RB > Configure/Setup> Identification> Field S/N or RB > Device Variables > Instrument > Identification> Field Serial Number
Firmware Revision RB > Configure/Setup> Version > Firmware Revision or RB > Device Variables > Instrument > Version > Firmware Revision
Function Block Options RB > Configure/Setup> Options > Function Block Options or RB > Device Variables > Options > Function Block Options
Hardware Revision RB > Configure/Setup> Version > Hardware Revision or RB > Device Variables > Instrument > Version > Hardware Revision
ITK Version RB > Configure/Setup> Version > ITK Version or RB > Device Variables > Instrument > Version > ITK Version
Limit Notify RB > Configure/Setup> Alarm Handling > Limit Notify
Manufacturer RB > Configure/Setup> Identification> Manufacturer or RB > Device Variables > Instrument > Identification> Manufacturer
Maximum Notify RB > Configure/Setup> Alarm Handling > Maximum Notify
Miscellaneous Options RB > Configure/Setup> Options >Miscellaneous Options or RB > Device Variables > Options >Miscellaneous Options
Resource Block Error RB > Device Diagnostics > Resource Block Error
Shed Remote Cascade RB > Configure/Setup> Communication Time Out > Shed Remote Cascade
Shed Remote Out RB > Configure/Setup> Communication Time Out > Shed Remote Out
Standby Firmware Revision RB > Configure/Setup> Version > Standby Software Revision or RB > Device Variables > Instrument > Version > Standby
Software Revision
Strategy RB > Configure/Setup> Identification> Strategy or RB > Device Variables > Instrument > Identification> Strategy
Tag Description RB > Configure/Setup> Identification> Tag Description or RB > Device Variables > Instrument > Identification> Tag Description
Write Alarm: Alarm State RB > Device Diagnostics > Write Lock > Write Alarm: Alarm State
Write Lock RB > Configure/Setup> Write Lock > Write Lock or RB > Device Diagnostics > Write Lock > Write Lock
Write Priority RB > Configure/Setup> Write Lock > Write Priority

xi
xi
FIELDVUE DVC6000f Digital Valve Controller
THE FIELDVUE DVC6000f DIGITAL VALVE CONTROLLER IS A CORE COMPONENT OF THE PLANTWEB
DIGITAL PLANT ARCHITECTURE. THE DIGITAL VALVE CONTROLLER POWERS PLANTWEB BY
CAPTURING AND DELIVERING VALVE DIAGNOSTIC DATA. COUPLED WITH VALVELINKSOFTWARE,
THE DVC6000f PROVIDES USERS WITH AN ACCURATE PICTURE OF VALVE PERFORMANCE, INCLUDING
ACTUAL STEM POSITION, INSTRUMENT INPUT SIGNAL AND PNEUMATIC PRESSURE TO THE
ACTUATOR. USING THIS INFORMATION, THE DIGITAL VALVE CONTROLLER DIAGNOSES NOT ONLY
ITSELF, BUT ALSO THE VALVE AND ACTUATOR TO WHICH IT IS MOUNTED.

Introduction and Specifications
December 2009 1-1
1-1
Section 1 Introduction and Specifications
Scope of Manual 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Description 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using this Manual 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Information 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fieldbus Installation and Wiring Guidelines 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Documents 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Educational Services 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1

DVC6000f Digital Valve Controllers
December 2009
1-2
Scope of Manual
This instruction manual includes specifications,
installation, operating, and maintenance information
for FIELDVUE DVC6000f digital valve controllers.
This manual describes device setup using the 475 or
375 Field Communicator. For information on using
Fisher ValveLink software with the instrument, refer to
the appropriate user guide or help.
Do not install, operate, or maintain a DVC6000f digital
valve controller without being fully trained and qualified
in valve, actuator, and accessory installation,
operation, and maintenance. To avoid personal injury
or property damage, it is important to carefully read,
understand, and follow all of the contents of this
manual, including all safety cautions and warnings. If
you have any questions about these instructions,
contact your Emerson Process Management sales
office before proceeding.
Note
Neither Emerson, Emerson Process
Management, nor any of their affiliated
entities assume responsibility for the
selection, use, or maintenance of any
product. Responsibility for the
selection, use, and maintenance of any
product remains with the purchaser
and end user.
Instrument Description
DVC6000f digital valve controllers for FOUNDATION
fieldbus are interoperable, communicating,
microprocessor-based, digital-to-pneumatic
instruments. In addition to the primary function of
converting a digital input signal to a pneumatic output,
the DVC6000f, using FOUNDATION fieldbus
communications protocol, gives easy access to
information critical to process operation as well as
process control. This can be done using a DeltaV
console, another FOUNDATION fieldbus system console,
or with ValveLink software.
DVC6000f digital valve controllers can be mounted on
single or double-acting sliding-stem actuators, as
shown in figure 1-1, or on rotary actuators, as shown
in figure 1-2. The DVC6000f mounts on most Fisher
and other manufacturers’ rotary and sliding-stem
actuators.
Figure1-1. FIELDVUE DVC6010f Digital Valve
Controller Mounted on Fisher 585C Piston Actuator
W9132-1
DVC6000f digital valve controllers are available with
several selections of control and diagnostic capability.
Control selections include:
Standard Control (SC)— Digital valve
controllers with Standard Control have the AO, PID,
ISEL, OS, AI, MAI, DO, and four DI function blocks in
addition to the resource and transducer blocks.
Fieldbus Control (FC)—Digital valve controllers
with Fieldbus Control have the AO function block in
addition to the resource and transducer blocks.
Fieldbus Logic (FL)—Digital valve controllers
with Fieldbus Logic have the DO, and four DI function
blocks, in addition to the resource and transducer
block.
The diagnostic capabilities include:
Performance Diagnostics (PD)
Advanced Diagnostics (AD)
Fieldbus Diagnostics (FD)
Performance and Advanced Diagnostics are available
with ValveLink software. They provide visibility to
instrument alerts. Fieldbus Diagnostics can be viewed
with any host system.
Instrument Blocks
The digital valve controller is a block-based device.
For detailed information on the blocks within the digital
1

Introduction and Specifications
December 2009 1-3
Figure 1-2. Fisher Rotary Control Valve with FIELDVUE
DVC6020f Digital Valve Controller
W8115-FF
valve controller, see the Detailed Setup section of this
manual.
All DVC6000f digital valve controllers include the
resource and transducer block:
Resource Block—The resource block contains
the hardware specific characteristics associated with a
device; it has no input or output parameters. The
resource block monitors and controls the general
operation of other blocks within the device. For
example, when the mode of the resource block is Out
of Service, it impacts all function blocks.
Transducer Block—The transducer block
connects the analog output function block to the I/P
converter, relay, and travel sensor hardware within the
digital valve controller.
Function Blocks
In addition to the resource and transducer block, the
digital valve controller may contain the following
function blocks. For additional information on function
blocks, refer to Appendix D, FOUNDATION fieldbus
Communication.
Analog Output (AO) Function Block—The
analog output function block accepts the output from
another function block (such as a PID block) and
transfers it as an actuator control signal to the
transducer block. If the DO block is selected, the AO
block is not functional.
Proportional-Integral-Derivative (PID)
Function Block—The PID function block performs
proportional-plus-integral-plus-derivative control.
Input Selector (ISEL) Function block—The
input selector function block selects from up to four
inputs and may provide the selected signal as input to
the PID block. The input selection can be configured
to select the first good input signal; a maximum,
minimum or average value; or a hot spare.
Output Splitter (OS) Function Block—The
output splitter function block accepts the output from
another function block (such as a PID block) and
creates two outputs that are scaled or split, according
to the user configuration. This block is typically used
for split ranging of two control valves.
Analog Input (AI) Function Block—The analog
input function block monitors the signal from a
DVC6000f sensor or internal measurement and
provides it to another block.
Multiple Analog Input (MAI) Function
Block—The Multiple Analog Input (MAI) function block
has the ability to process up to eight DVC6000f
measurements and make them available to other
function blocks.
Discrete Output (DO) Function Block—The
discrete output function block processes a discrete set
point and sends it to a specified output channel, which
can be transferred to the transducer block for actuator
control. In the digital valve controller, the discrete
output block provides both normal open/closed control
and the ability to position the valve in 5% increments
for course throttling applications. If the AO block is
selected, the DO block is not functional.
Discrete Input (DI) Function Block—The
discrete input function block processes a single
discrete input from a DVC6000f and makes it available
to other function blocks. In the digital valve controller,
the discrete input function block can provide limit
switch functionality and valve position proximity
detection.
1

DVC6000f Digital Valve Controllers
December 2009
1-4
Using This Manual
Procedures that require the use of the Field
Communicator have the Field Communicator symbol
in the heading.
Also included is the path required to accomplish
various tasks; the sequence of steps through the Field
Communicator menus. For example, the path to
Resource Block Mode is RB >Configure/Setup >
Setup >Resource Block Mode.
An overview of the Field Communicator resource block
and transducer block menu structures are shown at
the beginning of this manual. Menu structures for the
function blocks are included with each function block
section in Detailed Setup / Blocks.
Throughout this document, parameters are typically
referred to by their common name or label, followed by
the parameter name and index number; for example,
Write Priority (WRITE_PRI [39]). However, not all
interface systems support the use of the parameter
label and instead use only the Parameter Name,
followed by the index number, when referring to the
block parameters.
Specifications
Specifications for DVC6000f digital valve controllers
are shown in table 1-1.
Related Information
Fieldbus Installation and Wiring
Guidelines
This manual describes how to connect the fieldbus to
the digital valve controller. For a technical description,
planning, and installation information for a FOUNDATION
fieldbus, refer to the FOUNDATION fieldbus Technical
Overview available from the Fieldbus Foundation and
Fieldbus Installations in a DeltaV System available
from your Emerson Process Management sales office.
Related Documents
Other documents containing information related to
DVC6000f digital valve controllers include:
Bulletin 62.1:DVC6000f—Fisher FIELDVUE
DVC6000f Digital Valve Controllers (D103199X012)
Bulletin 62.1:DVC6000(S1)—Fisher FIELDVUE
DVC6000, DVC6000 SIS, and DVC6000f Digital Valve
Controller Dimensions (D103308X012)
Bulletin 62.1:DVC6000f(S1)—Fisher FIELDVUE
DVC6000f Digital Valve Controller Custom
Configuration (D103419X012)
Fisher FIELDVUE DVC6000f Digital Valve
Controller Quick Start Guide (D103202X012)
ValveLink Software Help or Documentation
Field Communicator User’s Manual
DeltaV Online Help or documentation
All documents are available from your Emerson
Process Management sales office. Also visit our
website at www.FIELDVUE.com.
EducationalServices
For information on available courses for DVC6000f
digital valve controllers, as well as a variety of other
products, contact:
Emerson Process Management
Educational Services, Registration
P.O. Box 190; 301 S. 1st Ave.
Marshalltown, IA 50158−2823
Phone: 800−338−8158 or
Phone: 641−754−3771
FAX: 641−754−3431
e-mail: [email protected]
1

Introduction and Specifications
December 2009 1-5
Table 1-1. Specifications
Available Configurations
DVC6010f: Sliding-stem applications
DVC6020f: Rotary and long-stroke sliding-stem
applications [over 102 mm (4 inch) travel]
DVC6030f: Quarter-turn rotary applications
Remote-Mounted Instrument(1)
DVC6005f: Base unit for 2 inch pipestand or wall
mounting
DVC6015: Feedback unit for sliding-stem
applications
DVC6025: Feedback unit for rotary or long-stroke
sliding-stem applications
DVC6035: Feedback unit for quarter-turn rotary
applications
DVC6000f digital valve controllers can be mounted
on Fisher and other manufacturers rotary and
sliding-stem actuators.
Function Block Suites
Standard Control (throttling control)
Includes AO, PID, ISEL, OS, AI, MAI, DO, and four
DI function blocks
Fieldbus Control (throttling control)
Contains the AO function block
Fieldbus Logic [discrete on/off]
Includes DO, and four DI function blocks
Block Execution Times
AO Block: 15 ms AI Block: 15 ms
PID Block: 20 ms MAI BLock: 35 ms
ISEL Block: 20 ms DO Block: 15 ms
OS Block: 20 ms DI Block: 15 ms
Electrical Input
Voltage Level: 9 to 32 volts
Maximum Current: 19 mA
Reverse Polarity Protection: Unit is not polarity
sensitive
Termination: Bus must be properly terminated per
ISA SP50 guidelines
Digital Communication Protocol
FOUNDATIONfieldbus registered device
Physical Layer Type(s):
121—Low−power signaling, bus−powered, Entity
Model I.S.
511—Low−power signaling, bus−powered, FISCO
I.S.
Fieldbus Device Capabilities
Backup Link Master capable
Device Description Compatibility
Firmware Revision DD Compatibility
2.0 2 and 3
Output Signal
Pneumatic signal as required by the actuator, up to
full supply pressure.
Minimum Span: 0.4 bar (6 psig)
Maximum Span: 9.5 bar (140 psig)
Action: Double, Single direct, and Single reverse
Supply Pressure(2)
Recommended: 0.3 bar (5 psi) higher than
maximum actuator requirements, up to maximum
supply pressure
Maximum: 10 bar (145 psig) or maximum pressure
rating of the actuator, whichever is lower
Medium: Air or Natural Gas(3)
Air Quality: Supply pressure must be clean, dry air
that meets the requirements of ISA Standard
7.0.01. A maximum 40 micrometer particle size in
the air system is acceptable. Further filtration down
to 5 micrometer particle size is recommended.
Lubricant content is not to exceed 1 ppm weight
(w/w) or volume (v/v) basis. Condensation in the air
supply should be minimized
Natural Gas: Natural gas must be clean, dry,
oil-free, and noncorrosive. H2S content should not
exceed 20 ppm.
Steady-State Air Consumption(4,5)
Standard Relay: At 1.4 bar (20 psig) supply
pressure: Less than 0.38 normal m3/hr (14 scfh)
At 5.5 bar (80 psig) supply pressure: Less than 1.3
normal m3/hr (49 scfh)
Low Bleed Relay: At 1.4 bar (20 psig) supply
pressure: Average value 0.056 normal m3/hr
(2.1 scfh)
At 5.5 bar (80 psig) supply pressure: Average value
0.184 normal m3/hr (6.9 scfh)
Maximum Output Capacity(4,5)
At 1.4 bar (20 psig) supply pressure:
10.0 normal m3/hr (375 scfh)
At 5.5 bar (80 psig) supply pressure:
29.5 normal m3/hr (1100 scfh)
−continued−
1

DVC6000f Digital Valve Controllers
December 2009
1-6
Table 1-1. Specifications (continued)
Independent Linearity(6)
±0.5% of output span
Electromagnetic Compatibility
Meets EN 61326-1 (First Edition)
Immunity—Industrial locations per Table 2 of the
EN 61326-1 standard. Performance is shown
in table 1-2 below
Emissions—Class A
ISM equipment rating: Group 1, Class A
Lightning and Surge Protection—The degree of
immunity to lightning is specified as Surge immunity
in table 1-2. For additional surge protection
commercially available transient protection devices
can be used.
Vibration Testing Method
Tested per ANSI/ISA-75.13.01 Section 5.3.5. A
resonant frequency search is performed on all three
axes. The instrument is subjected to the ISA
specified 1/2 hour endurance test at each major
resonance, plus an additional two million cycles.
Operating Ambient Temperature Limits(2)
−40 to 80C (−40 to 176F) for most approved
valve-mounted instruments.
−60 to 125C (−76 to 257F) for remote-mounted
feedback unit.
−52 to 80C (−62 to 176F) for valve-mounted
instruments utilizing the Extreme Temperature
option (fluorosilicone elastomers)
Electrical Classification
CSA— Intrinsically Safe, and FISCO, Explosion
proof, Division 2, Dust-Ignition proof
FM— Intrinsically Safe and FISCO, Explosion
proof, Non-incendive, Dust-Ignition proof
ATEX—Intrinsically Safe and FISCO, Flameproof,
Type n
IECEx— Intrinsically Safe and FISCO, Flameproof,
Type n
NEPSI—Intrinsically Safe, Flameproof
Refer to Special Instructions for “Safe Use” and
Installation in Hazardous Locations in section 2,
tables 1-3, 1-4, 1-5, 1-6, and 1-7 and Appendix B
for specific approval information.
Electrical Housing:
CSA—Type 4X, IP66
FM—NEMA 4X
ATEX—IP66
IECEx—NEMA 4X, IP66
NEPSI—IP66
Other Classifications/Certifications
TIIS—Japan
GOST-R—Russian GOST-R
FSETAN—Russian - Federal Service of
Technological, Ecological and Nuclear Inspectorate
INMETRO—Brazil
Contact your Emerson Process Management sales
office for classification/certification specific
information
Connections
Supply Pressure: 1/4 NPT internal and integral
pad for mounting 67CFR regulator
Output Pressure: 1/4 NPT internal
Tubing: 3/8-inch metal, recommended
Vent: 3/8 NPT internal
Electrical: 1/2 NPT internal, M20 adapter optional
Stem/Shaft Travel
Linear Actuators with rated travel between
6.35 mm (0.25 inch) and 606 mm (23.875 inches)
Rotary Actuators with rated travel between 50
degrees and 180 degrees
Mounting(7)
Designed for direct actuator mounting or remote
pipestand or wall mounting. Mounting the
instrument vertically, with the vent at the bottom of
the assembly, or horizontally, with the vent pointing
down, is recommended to allow drainage of
moisture that may be introduced via the instrument
air supply.
Weight
Valve-Mounted Instruments
Aluminum: 3.5 Kg (7.7 lbs)
Stainless Steel: 7.7 Kg (17 lbs)
Remote-Mounted Instruments
DVC6005f Base Unit: 4.1 Kg (9 lbs)
DVC6015 Feedback Unit: 1.3 Kg (2.9 lbs)
DVC6025 Feedback Unit: 1.4 Kg (3.1 lbs)
DVC6035 Feedback Unit: 0.9 Kg (2.0 lbs)
−continued−
1

Introduction and Specifications
December 2009 1-7
Table 1-1. Specifications (continued)
Options
Supply and output pressure gauges or Tire
valves, Integral mounted filter regulator,
Stainless steel housing, module base and
terminal box (valve-mounted instruments only),
Low bleed relay, Inline 10 micron air filter
Declaration of SEP
Fisher Controls International LLC declares this
product to be in compliance with Article 3 paragraph
3 of the Pressure Equipment Directive (PED) 97 /
23 / EC. It was designed and manufactured in
accordance with Sound Engineering Practice (SEP)
and cannot bear the CE marking related to PED
compliance.
However, the product may bear the CE marking to
indicate compliance with other applicable European
Community Directives.
NOTE: Specialized instrument terms are defined in ANSI/ISA Standard 51.1 −Process Instrument Terminology.
1. 3-conductor shielded cable, 22 AWG minimum wire size, is required for connection between base unit and feedback unit. Pneumatic tubing between base unit output connection and actuator
has been tested to 15 meters (50 feet) maximum without performance degradation.
2. The pressure/temperature limits in this manual and any applicable code or standard should not be exceeded.
3. Gas Certified DVC6000f digital valve controllers are FM and CSA Single Seal approved for use with natural gas as the supply medium.
4. Normal m3/hour −Normal cubic meters per hour at 0C and 1.01325 bar, absolute. Scfh −Standard cubic feet per hour at 60F and 14.7 psia.
5. Values at 1.4 bar (20 psig) based on a single-acting direct relay; values at 5.5 bar (80 psig) based on double-acting relay.
6. Typical value. Not applicable for travels less than 19 mm (0.75 inch) or for shaft rotation less than 60 degrees. Also, not applicable to DVC6020f digital valve controllers in long-stroke
applications.
7 . Do not use the DVC6010fS or DVC6020fS in high vibration service where the mounting bracket uses standoffs (spacers) to mount to the actuator. Due to NAMUR mounting limitations,
do not use the DVC6030fS in high vibration service.
Table1-2. EMC Summary Results—Immunity
Port Phenomenon Basic Standard Test Level Performance Criteria(1)
Enclosure
Electrostatic discharge (ESD) IEC 61000-4-2 4 kV contact
8 kV air A
Radiated EM field IEC 61000-4-3 80 to 1000 MHz @ 10V/m with 1 kHz AM at 80% 1400 to 2000 MHz @ 3V/m with 1 kHz AM at 80%
2000 to 2700 MHz @ 1V/m with 1 kHz AM at 80% A
Rated power frequency
magnetic field IEC 61000-4-8 60 A/m at 50 Hz A
I/O signal/control Burst IEC 61000-4-4 1 kV A
Surge IEC 61000-4-5 1 kV (line to ground only, each) B
Conducted RF IEC 61000-4-6 150 kHz to 80 MHz at 3 Vrms A
1. A = No degradation during testing. B = Temporary degradation during testing, but is self-recovering.
1

DVC6000f Digital Valve Controllers
December 2009
1-8
Table 1-3. Hazardous Area Classifications—CSA (Canada)
Certification
Body Type Certification Obtained Entity Rating Temperature Code Enclosure Rating
CSA
DVC60x0F
DVC60x0FS
(x = 1,2,3)
Ex ia—Intrinsically Safe & FISCO
Class I,II,III Division 1 GP A,B,C,
D,E,F,G per drawing GE42818
Natural Gas Approved
FIELDBUS
T4(Tamb v80C)
T5(Tamb v77C)
T6(Tamb v62C)
Type 4X, IP66
Single Seal Device
Vmax = 24 VDC
Imax = 380 mA
Ci = 5 nF
Li = 0 mH FISCO
Vmax = 17.5 VDC
Imax = 380 mA
Ci = 5 nF
Li = 0 mH
Pi = 5.32 W
Explosion Proof
Class I Division 1 GP B,C,D T6
Natural Gas Approved −−−T6(Tamb v80C) Type 4X, IP66
Single Seal Device
Class I Division 2 GP A,B,C,D T6
Class II Division 1,2 GP E,F,G T6
Class III
Natural Gas Approved
−−−T6(Tamb v80C) Type 4X, IP66
Single Seal Device
DVC6005F
Ex ia—Intrinsically Safe & FISCO
Class I,II,III Division 1 GP A,B,C,
D,E,F,G per drawing GE42818
Natural Gas Approved
FIELDBUS
T4(Tamb v80C)
T5(Tamb v77C)
T6(Tamb v62C)
Type 4X, IP66
Single Seal Device
Vmax = 24 VDC
Imax = 380 mA
Ci = 5 nF
Li = 0 mH
Pi = 1.4 mW
Voc = 24 VDC
Isc = 17.5 mA
Ca = 121 nF
La = 100 mH
Po = 105 mW
FISCO
Vmax = 17.5 VDC
Imax = 380 mA
Ci = 5 nF
Li = 0 mH
Pi = 5.32 mW
Voc = 24 VDC
Isc = 17.5 mA
Ca = 121 nF
La = 100 mH
Pi = 105 mW
Explosion Proof
Class I Division 1 GP B,C,D T6
Natural Gas Approved −−−T6(Tamb v80C) Type 4X, IP66
Single Seal Device
Class I Division 2 GP A,B,C,D T6
Class II Division 1,2 GP E,F,G T6
Class III
Natural Gas Approved
−−−T6(Tamb v80C) Type 4X, IP66
Single Seal Device
DVC60x5
(x = 1,2,3)
Ex ia— Intrinsically Safe
Class I,II,III Division 1 GP A,B,C,
D,E,F,G per drawing GE42818
Vmax = 30 VDC
Imax = 17.5 mA
Ci = 0 uF
Li = 0 mH
Pi = 105 mW
T4(Tamb v125C)
T5(Tamb v95C)
T6(Tamb v80C) Type 4X, IP66
Explosion Proof
Class I Division 1 GP B,C,D −−−
T4(Tamb v125C)
T5(Tamb v95C)
T6(Tamb v80C) Type 4X, IP66
Class I Division 2 GP A,B,C,D
Class II Division 1,2 GP E,F,G −−−
T4(Tamb v125C)
T5(Tamb v95C)
T6(Tamb v80C) Type 4X, IP66
1