Emerson 1410 A/B User manual

Quick Start Guide
00825-0200-4410, Rev EA
May 2018
Emerson™Wireless 1410 A/B and 1410D
Gateway with 781 Field Link
00825-0200-4410_RevEA.fm Page 1 Thursday, May 10, 2018 1:26 PM

May 2018
2
Quick Start Guide
NOTICE
This guide provides basic guidelines for the Emerson Wireless 1410 and 1410D Gateway. It does not provide
instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the Emerson Wireless Gateway
1410 Reference Manual for more information and instructions. The manuals and this guide are available
electronically on Emerson.com/Rosemount.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions. This device
may not cause harmful interference. This device must accept any interference received, including interference
that may cause undesired operation. This device must be installed to ensure a minimum antenna separation
distance of 20 cm from all persons.
Explosion hazard
Do not make or break any connections to the Gateway while circuits are live unless area is known to be
non-hazardous.
Explosions could result in death or serious injury.
Installation of this device in an explosive environment must be in accordance with the appropriate local,
national, and international standards, codes, and practices. Review the Product Certifications section for any
restrictions associated with a safe installation.
Avoid contact with the leads and terminals. High voltage that may be present on leads can cause electrical
shock.
Potential electrostatic charging hazard
The Gateway enclosure is plastic. Use care in handling and cleaning when in explosive environments to avoid
an electrostatic discharge.
Contents
Wireless planning . . . . . . . . . . . . . . . . . . . . . . . . 3
PC requirements . . . . . . . . . . . . . . . . . . . . . . . . . 3
Initial connection and configuration . . . . . . . . 3
Physical installation . . . . . . . . . . . . . . . . . . . . . . 11
Software installation (optional) . . . . . . . . . . . 20
Verify operations . . . . . . . . . . . . . . . . . . . . . . . . 21
Product Certification . . . . . . . . . . . . . . . . . . . . 23
00825-0200-4410_RevEA.fm Page 2 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
3
May 2018
1.0 Wireless planning
1.1 Power up sequence
The Gateway should be installed and functioning properly before power
modules are installed in any wireless field devices. Wireless field devices should
also be powered up in order of proximity from the Gateway beginning with the
closest. This will result in a simpler and faster network installation.
1.2 Antenna position
The antenna should be positioned vertically and be approximately 6 ft. (2 m)
from large structures or buildings to allow for clear communication to other
devices.
1.3 Mounting height
For optimal wireless coverage, the remote antenna is ideally mounted 15–25 ft.
(4.6–7.6 m) above ground or 6 ft. (2 m) above obstructions or major
infrastructure.
2.0 PC requirements
2.1 Operating system (optional software only)
Microsoft®Windows™Server 2008 (Standard Edition), Service Pack 2
Windows Server 2008 R2 Standard Edition, Service Pack 1
Windows 7 Professional, Service Pack 1
Windows 7 Enterprise, Service Pack 1
Windows 8 Enterprise, Service Pack 1
Windows 10 Enterprise, Service Pack 1
2.2 Applications
Configuration of the Gateway is done through a secure web interface. Recent
versions of the following browsers are supported:
Internet Explorer®
Chrome™browser
Mozilla Firefox®
Microsoft Edge
2.3 Hard disk space
AMS Wireless Configurator: 1.5 GB
Gateway Setup CD: 250 MB
3.0 Initial connection and configuration
To configure the Gateway, a local connection between a PC/Mac/laptop and the
Gateway needs to be established. The Emerson 1410 and 1410D are
operationally equivalent and the following instructions are applicable to both
models.
00825-0200-4410_RevEA.fm Page 3 Thursday, May 10, 2018 1:26 PM

May 2018
4
Quick Start Guide
3.1 Powering the Gateway
For both Emerson Wireless 1410A/B and the 1410D, bench top power will be
needed to power the Gateway by wiring a 10.5–30 VDC (20–30 VDC if a 781 is
connected with I.S. barriers to the Emerson 1410D) power source, with a
capacity of at least 250 mA to the power terminals.
Figure 1. Emerson 1410A/B Gateway Housing
A. DIN Rail clip
B. SMA to N type connection
C. Power light. During normal operation the power indicator will be green.
D. Ethernet port 2. When this port is activated, the factory IP address is 192.168.2.10. See
Table 1 on page 9.
E. Ethernet port 1. Use for standard communication to the webserver or other protocols
enabled on the Gateway. The factory IP address is 192.168.1.10. See Table 1 on page 9.
F. Emerson 1410 power and serial connection. Black terminal included in the box.
+-A+ B-
24 VDC
(nominal)
Power Input
Serial
Modbus
S
Power
Reset
A
B
C
D
E
F
00825-0200-4410_RevEA.fm Page 4 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
5
May 2018
Figure 2. Emerson 1410D Gateway Wiring
A. DIN Rail Clip
B. Power light. During normal operation the power indicator will be green.
C. Ethernet port 2. When this port is activated, the factory IP address is 192.168.2.10. See
Table 1 on page 9.
D. Ethernet port 1. When this port is activated, the factory IP address is 192.168.1.10. See
Table 1 on page 9.
E. Emerson 1410 Power and Serial connections. Black terminal included in the box.
F. Emerson Wireless 781 Field Link power and data connections. Black terminal included in
box.
A
B
C
D
E
F
E
F
00825-0200-4410_RevEA.fm Page 5 Thursday, May 10, 2018 1:26 PM

May 2018
6
Quick Start Guide
3.2 Establishing a connection
Connect the PC/laptop to the Ethernet 1 (Primary) receptacle on the Gateway
using an Ethernet cable.
Windows 7
1. Click the Internet Access icon on the bottom right of the screen.
Figure 3. Internet Access
2. Select the Network and Sharing Center.
3. Select Local Area Connection.
Figure 4. Local Area Connection
4. Select Properties.
00825-0200-4410_RevEA.fm Page 6 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
7
May 2018
5. Select Internet Protocol Version 4 (TCP/IPv4) then select Properties.
Figure 5. Internet Protocol Version 4 (TCP/IPv4)
Note
If the PC/laptop is from another network, record the current IP address and other settings
so the PC/laptop can be returned to the original network after the Gateway has been
configured.
6. Select the Use the following IP address button.
Figure 6. IP Address
7. In the IP address field, enter 192.168.1.12 (DeltaV Ready enter 10.5.255.12).
8. In the Subnet mask field, enter 255.255.255.0.
00825-0200-4410_RevEA.fm Page 7 Thursday, May 10, 2018 1:26 PM

May 2018
8
Quick Start Guide
9. Select OK for both the Internet Protocol (TCP/IP) Properties window and the
Local Area Connection Properties window.
Windows 10
1. Select the network icon in the lower right corner.
2. Select the Network settings link.
3. Select Ethernet on the left hand side of the Network Settings dialog.
1
2
00825-0200-4410_RevEA.fm Page 8 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
9
May 2018
4. Select Change adapter options.
5. See steps 4-10 from Windows 7 instructions.
Note
Connecting to the Gateway's secondary Ethernet port will require different network
settings.
Disable proxies
1. Open web browser.
2. Navigate Tools >I nternet Options > Connections > LAN Settings (may be a
different process for other browsers).
3. Under Proxy server, uncheck the Use a proxy server... box.
Table 1. TCP/IP Network Settings
Gateway PC/laptop/tablet Subnet
Ethernet 1 192.168.1.10 192.168.1.12 255.255.255.0
Ethernet 2 192.168.2.10 192.168.2.12 255.255.255.0
00825-0200-4410_RevEA.fm Page 9 Thursday, May 10, 2018 1:26 PM

May 2018
10
Quick Start Guide
3.3 Configure the Gateway
To complete initial configuration for the Gateway:
1. Access the default web page for the Gateway at https://192.168.1.10
a. Log on as Username: admin
b. Type in password: default
2. Navigate to System Settings > Gateway > Ethernet Communication to enter the
Network Settings.
a. Configure a static IP Address or set for DHCP and enter a Hostname.
b. Restart application at System Settings > Gateway > Backup and Restore >
Restart Apps.
Note
Resetting applications will temporarily disable communications with field devices.
3. Disconnect the power and Ethernet cable from the Gateway.
00825-0200-4410_RevEA.fm Page 10 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
11
May 2018
4.0 Physical installation
4.1 Emerson 1410A/B and 1410D mounting
The unit can be snapped onto a DIN TS35/7.5 or TS35/15 rail system. To clip the
unit onto the DIN rail, see Figure 7.
1. Tilt the unit at a slight angle allowing the lower lip of the chassis to catch the
bottom of the DIN rail.
2. Apply pressure forward to snap the back of the unit securely onto the DIN
rail.
Figure 7. Installing
To remove the unit, see Figure 8.
1. Place a flat or rounded object (such as a screw driver) into the DIN clip and
apply a slight pressure downwards on the object.
2. Once the unit is released from the DIN rail, pull backwards and down to
successfully disengage.
00825-0200-4410_RevEA.fm Page 11 Thursday, May 10, 2018 1:26 PM

May 2018
12
Quick Start Guide
Figure 8. Removing
Note
Do not mount the antenna within a metal enclosure. To avoid damage to sensitive RF
components, do not remove protective cap from the Gateway SMA connector until ready
to install the antenna.
4.2 Connecting the Emerson 1410D with 781
There are two main connection configurations for the Emerson 1410D and 781:
with and without barriers. The location and hazardous approval option of the
Emerson 781 determines whether it needs to be installed with barriers.
NOTICE
When mounting the unit in an electrical enclosure or other location, comply with the appropriate local and
national installation codes. Verify that the installer, associated hardware, and installation equipment used have
the proper certifications for the specific type of installation being performed. Before installation, verify if local
codes require a permit and/or an inspection before energizing. When planning the installation, account for
routing the antenna cable within the enclosure.
00825-0200-4410_RevEA.fm Page 12 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
13
May 2018
Installation without barriers
A shielded twisted pair cable is needed for connecting the Emerson 1410D and
781 (refer to Figure 9). The Emerson 781 can be located up to 656 ft. (200m)
from the Emerson 1410D.
Figure 9. Emerson 1410D and 781 without Barriers Installation
A.Emerson Wireless1410DGateway
B. Attach shield pair cable (Belden 3084A
or equivalent)
C. Tape back shield wire and foils
D. Short these terminals to enable 250 Ω
terminating resistor
E. Emerson Wireless 781 Field Link
Data A (+)
Data B (-)
Return (-)
24 VDC (+)
Blu
Wht
Red
Blk
C
E
D
B
A
Red
Blk
Blu
Wht
10.5-30VDC
Gray line means internal
connection
00825-0200-4410_RevEA.fm Page 13 Thursday, May 10, 2018 1:26 PM

May 2018
14
Quick Start Guide
Installation with barriers
When installing the Emerson 781 in a hazardous area there are two I.S. barriers
that need to be installed: a power barrier and a signal barrier. The signal and the
power are two separate I.S. circuits so they must comply with proper I.S.
segregation distance. When using the Emerson recommended barriers the
input power of the Gateway should be 20–30 VDC, with current capacity of at
least 330 mA.
The signal barrier needs additional power. You can wire it to the Emerson 1410D
terminals or to a separate power supply. Make sure power supply is rated to
handle power drawn for the barrier. Figure 10 and Figure 11 show the two
variations of powering the signal barrier.
Figure 10. Emerson 1410D and 781 with Gateway Powered Barrier
Installation
A.Emerson Wireless1410DGateway
B. Attach shield pair cable (Belden 3084A)
C. Tape back shield wire and foils
D. Short these terminals for 250 Ω
E. Emerson Wireless 781 Field Link
F. I.S. segregation
G. Shield
B
+
-
Data+ Data -
- +
+ -
Power
Barrier
Signal
Barrier
Red
Blk
Blu
Wht
20-30 VDC
20-30 VDC
Data+Data -
Safe Area
A
Red Blk
Wht Blu
Gray line means internal
connection
Blu Red Blk
C
Data A (+)
Data B (-)
Return (-)
24 VDC (+)
E
Wht
D
Hazardous Area
F
G
00825-0200-4410_RevEA.fm Page 14 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
15
May 2018
Figure 11. Emerson 1410D and 781 with Additional Power Supplied Barrier
Installation
Recommendation
Signal barrier
GM-International D1016S
Power barrier
Stahl 9176 10-16-00
A . E m e r s o n W i r e l e s s 1 4 1 0 D G a t e wa y
B. Attach shield pair cable (Belden 3084A)
C. Tape back shield wire and foils
D. Short these terminals for 250 Ω
E. Emerson Wireless 781 Field Link
F. I.S. segregation
G. Shield
B
+
-
Data+ Data -
- +
+ -
Power
Barrier
Signal
Barrier
Red
Blk
Blu
Wht
20-30 VDC
20-30 VDC
Power
Supply
Data+Data -
Safe Area
A
Red Blk
Wht Blu
Gray line means internal
connection
Blu Red Blk
C
Data A (+)
Data B (-)
Return (-)
24 VDC (+)
E
Wht
D
Hazardous Area
F
G
00825-0200-4410_RevEA.fm Page 15 Thursday, May 10, 2018 1:26 PM

May 2018
16
Quick Start Guide
Shield grounding
The shield of the twisted pair cable needs to be grounded using the grounding
terminal on the Emerson 1410D, and it should be taped back on the Emerson
781 side.
Emerson 1410D Grounding
The Emerson 1410D DIN rail cabinet must be grounded as well. A #6 AWG
(4.11 mm European) copper wire bonding connector with the shortest length
possible, no sharp bends, and no coiling is recommended.
Figure 12. Emerson 1410D Grounding
A. #6 AWG copper wire
B. Protective ground
C. Reference ground (when present)
D. Earth
(May be polymer with
grounding plate)
2
1
A
A
B
D
00825-0200-4410_RevEA.fm Page 16 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
17
May 2018
Emerson 781 grounding
Grounding of the electronics enclosure should be done in accordance with local
and national installation codes. Grounding is accomplished through the external
case grounding terminal.
A. Grounding lug
Terminating resistances
For best performance, the terminating resistances should be matched across
the Emerson 1410D, 781, and the signal barrier. The Emerson 1410D has an
integral 250 Ωterminating resistor. Short the Emerson 781 terminator
terminals to engage a 250 Ωresistor (note D of Figure 10 and Figure 11). The
recommended barriers can also be switched to 250 Ω.
4.3 Connecting the Emerson 1410A/B with the remote antenna
Use only Emerson provided remote antenna, coaxial RF cable, and lightning
arrestor. The remote antenna lightning arrestor must be installed and grounded
in accordance with Figure 13.
Locate the remote antenna to achieve optimal wireless performance. Ideally this
will be 15–25 ft. (4.6–7.6 m) above the ground or 6 ft. (2 m) above obstructions
or major infrastructure. To install the remote antenna, use one of the following
procedures:
When installing remote mount antennas for the Gateway, always use established safety procedures to avoid
falling or contact with high-power electrical lines.
Install remote antenna components for the Gateway in compliance with local and national electrical codes and
use best practices for lightning protection.
Before installing, consult with the local area electrical inspector, electrical officer, and work area supervisor.
The Gateway remote antenna option is specifically engineered to provide installation flexibility while optimizing
wireless performance and local spectrum approvals. To maintain wireless performance and avoid
non-compliance with spectrum regulations, do not change the length of cable or the antenna type.
If the supplied remote mount antenna kit is not installed per these instructions, Emerson is not responsible for
wireless performance or non-compliance with spectrum regulations.
A
00825-0200-4410_RevEA.fm Page 17 Thursday, May 10, 2018 1:26 PM

May 2018
18
Quick Start Guide
Installation of WL2/WN2 option
1. Mount the antenna on a 11/2- to 2-in. pipe mast using the supplied mounting
equipment.
2. Connect the lightning arrestor either to the electrical cabinet or directly
outside the wall or right outside the wall (depending on where the Gateway is
located).
3. Install the grounding lug, lock washer, and nut on top of the lightning
arrestor.
4. Bond the grounding terminal of the lightning arrestor to a common earth
point using individual high integrity, low resistance means as shown in
Figure 13.
5. The DIN rail cabinet must be grounded as well. A #6 AWG (or 4.11 mm
European) copper wire bonding conductor with the shortest length possible,
no sharp bends, and no coiling is recommended.
6. All the outdoor connections should be made hand tight plus an 1/8th turn with
a wrench and wrapped with the coaxial seal (shown in Figure 14).
7. Ensure the mounting mast, lightning arrestor, and Gateway are grounded
according to local/national electrical code.
Any spare lengths of coaxial cable should be placed in 1 ft. (0.3 m) coils.
00825-0200-4410_RevEA.fm Page 18 Thursday, May 10, 2018 1:26 PM

Quick Start Guide
19
May 2018
Figure 13. Installation of WL2/WN2 Option
Note: Weather proofing is required
The remote mount antenna kit includes coaxial sealant for the cable connections for the
lightning arrestor, antenna, and Gateway. The coaxial sealant must be applied to
guarantee performance of the wireless field network. See Figure 14 for details on how to
apply weather proofing.
Figure 14. Applying Coaxial Sealant to Cable Connections
Indoor/outdoor cabinet and antenna Outdoor cabinet and antenna
A. To antenna
B. Coaxial RF
C. Drip loop
D. Lightning arrestor
E. Type N bulkhead connector
F. 5/8-in. ring terminal
G. #6 AWG copper wire
H. Transient protection ground
I. Outdoor rated enclosure
J. Protective ground
K. Earth
L. Seal per Figure 13
InsideOutside
2
1
300 mm (11.8-in.)
minimum bend radius
300 mm (11.8-in.)
minimum bend radius
Reference
ground
(when present)
(May be polymer with
grounding plate)
300 mm (11.8-in.)
minimum bend radius
2
1
A
A
B
B
B
C
C
D
D
E
EE
F
F
G
H
H
GG
J
I
K
L
L
00825-0200-4410_RevEA.fm Page 19 Thursday, May 10, 2018 1:26 PM

May 2018
20
Quick Start Guide
4.4 Connect to the host system
1. Wire the Gateway’s Ethernet 1 (Primary) or Serial Output connection to the
Host System Network or Serial I/O (see Figure 1 and Figure 2 for hardware
drawings).
2. For serial connections, make sure all terminations are clean and secure to
avoid wiring connection problems.
4.5 Best practice
Twisted shielded pair cable is generally used to wire the serial connection, and it
is standard practice to ground the shield on the serial host side leaving the shield
floating on the Gateway side. Insulate the shield to avoid grounding issues.
In accordance with Emerson WirelessHART®security guidelines (Emerson
Wireless Security Whitepaper), the Gateway should be connected to the Host
System via a LAN (Local Area Network) and not a WAN (Wide Area Network).
5.0 Software installation (optional)
The 2-disk software pack contains the Security Setup Utility (only required for
secure host connections or OPC communications) and AMS Wireless
Configurator. The Security Setup Utility is located on Disk 1. To install the
software:
1. Exit/close all Windows programs, including any running in the background,
such as virus scan software.
2. Insert Disk 1 into the CD/DVD drive of the PC.
3. If the setup program does not appear, go into the disc's file and run
autorun.exe.
4. Follow the prompts.
Table 2. Remote Antenna Kit Options
Kit option Antenna Cable 1 Cable 2 Lightning arrestor
WL2
1/2Wavelength Dipole
Omni-Directional
+6 dB Gain
50 ft. (15,2 m)
LMR-400 N/A
Head mount, jack to plug
Gas discharge tube
0.5 dB insertion loss
WN2
1/2Wavelength Dipole
Omni-Directional
+8 dB Gain
25 ft. (7,6 m)
LMR-400 N/A
Head mount, jack to plug
Gas discharge tube
0.5 dB insertion loss
00825-0200-4410_RevEA.fm Page 20 Thursday, May 10, 2018 1:26 PM