Emerson 1410S User manual

Quick Start Guide
00825-0600-4410, Rev BD
June2023
Emerson Wireless 1410S Gateway

Safety messages
NOTICE
This guide provides basic guidelines for the Emerson Wireless 1410S Gateway. It does not
provide instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the
Emerson Wireless Gateway 1410S Reference Manual for more information and instructions.
The manuals and this guide are available electronically on Emerson.com/Rosemount.
WARNING
Explosion hazard
Do not make or break any connections to the gateway while circuits are live unless area is
known to be non-hazardous.
Risque d'explosion
N'établissez ni ne rompez aucune connexion à la passerelle lorsque les circuits sont sous
tension, à moins que la zone ne soit connue comme étant non dangereuse.
Explosions could result in death or serious injury
Installation of device in an explosive environment must be in accordance with appropriate
local, national, and international standards, codes, and practices. Review the Product
Certifications section for any restrictions associated with a safe installation.
Avoid contact with leads and terminals. High voltage that may be present on leads can cause
electrical shock.
Les explosions peuvent entraîner la mort ou des blessures graves
L'installation de l'appareil dans un environnement explosif doit être conforme aux normes,
codes et pratiques locaux, nationaux et internationaux appropriés. Consultez la section
Certifications du produit pour toute restriction associée à une installation en toute sécurité.
Évitez tout contact avec les fils et les bornes. La haute tension qui peut être présente sur les
câbles peut provoquer un choc électrique.
Potential electrostatic charging hazard
The Emerson Wireless 1410S2 Gateway enclosure’s polyurethane paint finish may constitute
an electrostatic hazard. The Emerson Wireless 1410S1 Gateway is housed in a polymeric
enclosure that may constitute an electrostatic hazard. Use care in handling and cleaning
when in explosive environments to avoid an electrostatic discharge.
Risque potentiel de charge électrostatique
Voir les instructions.
Repair/maintenance
The Emerson Wireless 1410S Gateway contains no user serviceable components. If the device
is not functioning properly, see the troubleshooting guide in the Emerson Wireless 1410S
Gateway manual. If these troubleshooting steps do not resolve the problem, contact the
factory.
Quick Start Guide June2023
2 Emerson.com

WARNING
Physical access
Physical security is an important part of any security program and fundamental to protecting
your system. Unauthorized personnel may cause intentional or unintentional damage or
misconfiguration of the Emerson Wireless 1410S Gateway and connected field devices.
Restrict physical access by unauthorized personnel to protect end users’ assets.
CAUTION
Equipment conformance
Protection may be impaired if the device is used in a manner not specified by the
manufacturer.
NOTICE
The 1410S1 needs an external IP54 that meets the requirements of CAN/CSA 60079-0.
Le 1410S1 a besoin d'un IP54 externe qui répond aux exigences de CAN/CSA 60079-0.
Contents
Wireless planning.........................................................................................................................5
PC requirements.......................................................................................................................... 6
Initial connection and configuration......................................................................................... 7
Physical installation................................................................................................................... 18
Software installation (optional)................................................................................................ 28
Verify operations........................................................................................................................29
Product certifications................................................................................................................ 30
Declaration of Conformity........................................................................................................ 41
June2023 Quick Start Guide
Quick Start Guide 3

Quick Start Guide June2023
4 Emerson.com

1 Wireless planning
1.1 Power up sequence
The gateway should be installed and functioning properly before
power modules are installed in any wireless field devices. Wireless
field devices should also be powered up in order of proximity from
the gateway beginning with the closest. This will result in a simpler
and faster network installation.
1.2 Gateway redundancy
If the wireless gateway was ordered with redundancy (Gateway
Redundancy code RD), refer to Appendix D in the Emerson
Wireless 1420 Gateway Reference Manual for additional installation
instructions.
1.3 Gateway firmware compatability
The gateway firmware needs to be compatible with host connections
being made. Verify that gateway firmware and host firmware (e.g.
Security Setup Utility (SSU) and Plantweb Insight) are compatible
before commissioning.
June2023 Quick Start Guide
Quick Start Guide 5

2 PC requirements
2.1 Operating system (optional software only)
For security setup., Microsoft® supported Windows™ operating
systems are acceptable. Some examples are shown below:
•Microsoft Windows Server 2019 (Standard Edition), Service Pack 2
•Windows 10 Enterprise, Service Pack 1
2.2 Applications
Configuration of the gateway is done through a secure web interface.
Recent versions of the following browsers are supported:
•Chrome™ browser
•Mozilla Firefox®
•Microsoft Edge
2.3 Hard disk space
•AMS Wireless Configurator: 1.5 GB
•Gateway Setup CD: 250 MB
Quick Start Guide June2023
6 Emerson.com

3 Initial connection and configuration
To configure the gateway, a local connection between a computer
and the gateway needs to be established.
Powering the Gateway
For the Emerson Wireless 1410S Gateway, bench top power will be
needed to power the Gateway by wiring a 10.5–30 VDC power source.
An Emerson Wireless 1410S Gateway can also be powered via Power
over Ethernet (PoE) and is compliant with the IEEE 802.3af standard.
Note
The Emerson Wireless 1410S2 Gateway hardware revision 1.0.0
configured with Intrinsically Safe Outputs option “A” can only be
powered by 24 VDC power source. Check label to verify hardware
revision.
WARNING
Proper wiring for Emerson Wireless 1410S1 and 1410S2 Gateway
The 1410S1 and 1410S2 antenna terminals 1 and 2 must never be
connected directly to a power supply. Connecting these terminals to
anything other than the corresponding power and data terminals of
an antenna (e.g., 781S and 781 Field Link) may damage the Gateway.
For the 1410S1, the antenna terminals are located on the top of the
device.
For the 1410S2, after opening the cover, the antenna terminals are
located on the left side of the device.
Conduit/cable entries for Emerson Wireless 1410S2 Gateway
The conduit/cable entries in the transmitter housing use a ½–14 NPT
thread form. When installing in a hazardous location, use only
appropriately listed or Ex certified plugs, glands, or adapters in cable/
conduit entries.
Installer to ensure external conduit/cable fittings are Type 4X rated
or better (C22.2 No 94.2/UL 50E requirement).
June2023 Quick Start Guide
Quick Start Guide 7

Figure 3-1: Emerson Wireless 1410S1 Gateway Wiring
A. DIN-rail release tab
B. 781S terminal 1 power and data connections
C. 781S terminal 2 power and data connections
D. Ethernet port 1. When this port is activated, the factory IP address
is 192.168.1.10.
E. Ethernet port 2. When this port is activated, the factory IP address
is 192.168.2.10.
F. Emerson 1410S power and serial connections
G. 781S power terminals
H. 781S data terminals
I. 10.5 to 30 VDC power input(1)
J. Serial Modbus
K. 781S Antenna Terminals
L. 1410S Power Terminal
Quick Start Guide June2023
8 Emerson.com

Figure 3-2: Emerson Wireless 1410S2 Gateway Wiring
A. Mounting plate
B. 781S terminal 1 power and data connections
C. 781S terminal 2 power and data connections
D. Ethernet port 1. When this port is activated, the factory IP address
is 192.168.1.10.
E. Ethernet port 2. When this port is activated, the factory IP address
is 192.168.2.10.
F. Emerson 1410S power and serial connections
G. 781S power terminals
H. 781S data terminals
I. 10.5 to 30 VDC power input(1)
J. Serial modbus
K. External ground terminal
L. Internal ground terminal
M. 781A Antenna Terminals
N. 1410S Power Terminal
3.1 Establishing a connection
Connect the PC/laptop to the Ethernet 1 (Primary) receptacle on the
gateway using an Ethernet cable.
For DeltaV Ready Gateways, commission the gateway to the Deltav
system first. Proceed to Section 3.5 for updating user information.
Section 3.2-3.4 can be ignored for a DeltaV Ready Gateway.
(1) Emerson Wireless 1410S2 Gateway hardware revision 1.0.0 configured with
Intrinsically Safe Outputs option “A” can only be powered by 24 VDC power
source. Check label to verify hardware revision.
June2023 Quick Start Guide
Quick Start Guide 9

3.2 Windows 10
Procedure
1. Select the network icon in the lower right corner of the
Windows 10 workspace.
2. Select the Network & Internet Settings link.
Figure 3-3: WiFi Connections Menu
Quick Start Guide June2023
10 Emerson.com

3. Select Change adapter options.
Figure 3-4: Network & Internet Settings
4. Right click the network interface connection that the gateway
is plugged into, and select Properties.
June2023 Quick Start Guide
Quick Start Guide 11

5. Select Internet Protocol Version 4 (TCP/IPv4) → Properties.
Figure 3-5: Ethernet properties
Note
If the PC/laptop is from another network, record the current IP
address and other settings so the PC/laptop can be returned
to the original network after the gateway has been configured.
Quick Start Guide June2023
12 Emerson.com

6. Select the Use the following IP address button.
Figure 3-6: IP Address Properties
7. In the IP Address field, enter 192.168.1.11.
8. In the Subnet mask field, enter 255.255.255.0.
9. Select OK for both the Internet Protocol (TCP/IP) Properties
window and the Local Area Connection Properties window.
Note
Connecting to the gateway's secondary Ethernet port will
require different network settings.
Table 3-1: Network Settings
Ethernet Gateway PC/laptop/
tablet
Subnet
1 192.168.1.10 192.168.1.11 255.255.255.0
2 192.168.2.10 192.168.2.11
June2023 Quick Start Guide
Quick Start Guide 13

3.3 Disable proxies
This procedure may be necessary when using a Chrome browser with
Windows operating systems.
Procedure
1. Open web browser.
2. Navigate to Settings → Advanced.
3. In the System section, click Open proxy settings.
Example
Figure 3-7: Proxy settings menu. Only use if a proxy is needed.
Quick Start Guide June2023
14 Emerson.com

3.4 Configure the Gateway
To complete initial configuration for the gateway, follow the steps
below. This will have to be done be done for both networks.
Procedure
1. Access the default web page for the gateway at https://
192.168.1.10.
a) Log on as Username: admin
b) Type in password: default
Note
If the gateway has been connected properly, a security
certificate alert will be displayed in the web browser.
Proceed to the gateway web interface and log-in using
the following default credentials. Password should
be changed after initial sign-in. See Section 3.5 for
changing username and passwords.
Figure 3-8: User Name and Password
2. Navigate to System Settings → Gateway → Ethernet
Communication to enter the Network Settings.
a) Configure a static IP Address or set for DHCP and enter
a Host Name.
June2023 Quick Start Guide
Quick Start Guide 15

Figure 3-9: Ethernet Communication
Note
IP addresses will need to be user defined. See Figure
3-9 contains example IP addresses.
b) Restart application at System Settings → Gateway →
Backup and Restore → Restart Apps.
Note
Resetting applications will temporarily disable
communications with field devices.
3. Disconnect the power and Ethernet cable from the gateway.
3.5 Changing username and passwords
Procedure
1. Navigate to System Settings → Users → User Accounts to
change passwords and add users with the following steps.
a) For DeltaV Ready Gateways, access gateway web
interface from DeltaV Explorer.
2. Change admin, operator, maintenance, and executive
passwords to a secure password that adheres to user’s
password requirements.
Quick Start Guide June2023
16 Emerson.com

Figure 3-10: Navigating to User Accounts page
NOTICE
Changing passwords is HIGHLY SUGGESTED before installing
the gateway for full use.
WARNING
There is no way to recover lost passwords. The only way to
access a gateway that no longer has known credentials is to
factory reset the gateway. Doing a factory reset will clear all
user settings.
Figure 3-11: User Accounts page for updating changing
passwords
June2023 Quick Start Guide
Quick Start Guide 17

4 Physical installation
4.1 Emerson 1410S mounting
Find a location where the gateway has convenient access to the host
system network (process control network).
4.1.1 1401S1 DIN-rail mounting
The Emerson Wireless 1410S1 Gateway can be snapped onto a DIN
TS35/7.5 or TS35/15 rail system. To clip the gateway onto the DIN rail,
see Figure 4-1.
Prerequisites
•DIN-rail for mounting gateway
•Emerson Wireless 1410S1 Gateway
Procedure
1. Press down on the upper release tab of the gateway to release
the mounting clip.
2. Align top teeth on top of DIN-rail and rotate bottom teeth into
bottom of DIN-rail.
3. Release upper tab to secure the gateway to the DIN-rail.
4. To remove, press down on upper tab to release the gateway
from the DIN-rail.
NOTICE
When mounting the unit in an electrical enclosure or other
location, comply with the appropriate local and national
installation codes. Verify that the installer, associated
hardware, and installation equipment used have the proper
certifications for the specific type of installation being
performed. Before installation, verify if local codes require a
permit and/or an inspection before energizing. When planning
the installation, account for routing the antenna cable within
the enclosure.
Note
Do not mount the antenna within a metal enclosure. To avoid
damage to sensitive RF components, do not remove protective
cap from the gateway SMA connector until ready to install the
antenna.
Quick Start Guide June2023
18 Emerson.com

Figure 4-1: Emerson 1410S1 Mounting
June2023 Quick Start Guide
Quick Start Guide 19

4.1.2 1410S2 Pipe mount
Prerequisites
The following hardware and tools are needed to mount the gateway
to a 20-in. pipe:
•Two 5/16-in. u-bolts kits (supplied with gateway)
•2-in. mounting pipe
•1/2-in. wrench
Procedure
1. Insert one u-bolt around the pipe, through the top mounting
holes of the gateway mounting plate, and through the washer
plate.
2. Use a 1/2-in. wrench to fasten the nuts to the u-bolt.
3. Repeat for the second u-bolt and the lower mounting holes.
Figure 4-2: Emerson 1410S2 Mounting
4.1.3 1410S2 Surface mount
The following hardware and tools are needed to surface mount the
gateway to a support bracket:
Prerequisites
•Four appropriate fasteners for preferred mounting method
•Mounting plate (supplied with gateway)
•Drill (not supplied)
Quick Start Guide June2023
20 Emerson.com