Emerson 1410S User manual

Quick Start Guide
00825-0600-4410, Rev AA
March 2020
Emerson Wireless 1410S Gateway

Safety messages
NOTICE
This guide provides basic guidelines for the Emerson Wireless 1410S Gateway. It does not
provide instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the
Emerson Wireless Gateway 1410S Reference Manual for more information and instructions. The
manuals and this guide are available electronically on Emerson.com/Rosemount.
WARNING
Explosion hazard.
Do not make or break any connections to the Gateway while circuits are live unless area is known to be
non-hazardous.
Explosions could result in death or serious injury.
Installation of device in an explosive environment must be in accordance with appropriate local,
national, and international standards, codes, and practices. Review the Product Certifications section
for any restrictions associated with a safe installation.
Avoid contact with leads and terminals. High voltage that may be present on leads can cause electrical
shock.
Potential electrostatic charging hazard.
The Gateway enclosure is aluminum. Use care in handling and cleaning when in explosive
environments to avoid an electrostatic discharge.
Physical access
Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end
users’ equipment. This could be intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and fundamental to protecting your
system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for
all systems used within the facility.
Contents
Wireless planning.........................................................................................................................3
PC requirements.......................................................................................................................... 4
Initial connection and configuration.............................................................................................5
Physical installation.................................................................................................................... 15
Software installation (optional).................................................................................................. 19
Verify operations........................................................................................................................20
Product certifications................................................................................................................. 21
Reference data........................................................................................................................... 29
Quick Start Guide March 2020
2 Emerson.com

1 Wireless planning
1.1 Power up sequence
The Gateway should be installed and functioning properly before power
modules are installed in any wireless field devices. Wireless field devices
should also be powered up in order of proximity from the Gateway
beginning with the closest. This will result in a simpler and faster network
installation.
1.2 Gateway redundancy
If the wireless Gateway was ordered with redundancy (Gateway Redundancy
code RD), refer to Appendix D in the Emerson Wireless Gateway Reference
Manual for additional installation instructions.
March 2020 Quick Start Guide
Quick Start Guide 3

2 PC requirements
2.1 Operating system (optional software only)
For security setup. Microsoft® supported Windows™ operating systems are
acceptable. Some examples are shown below:
•Microsoft Windows Server 2019 (Standard Edition), Service Pack 2
•Windows 10 Enterprise, Service Pack 1
2.2 Applications
Configuration of the Gateway is done through a secure web interface.
Recent versions of the following browsers are supported:
•Chrome™ browser
•Mozilla Firefox®
•Microsoft Edge
2.3 Hard disk space
•AMS Wireless Configurator: 1.5 GB
•Gateway Setup CD: 250 MB
Quick Start Guide March 2020
4 Emerson.com

3 Initial connection and configuration
To configure the Gateway, a local connection between a computer and the
Gateway needs to be established.
Powering the Gateway
For the Emerson 1410S, bench top power will be needed to power the
Gateway by wiring a 10.5–30 VDC (24 VDC if configured with I.S. barriers)
power source.
Figure 3-1: Emerson 1410S Gateway Wiring
A. Mounting plate
B. Antenna terminal 1 power and data connections
C. Antenna terminal 2 power and data connections
D. Ethernet port 1. When this port is activated, the factory IP address is
192.168.1.10.
E. Ethernet port 2. When this port is activated, the factory IP address is
192.168.2.10.
F. Emerson 1410S power and serial connections
G. Power output
H. RS-485 comm
I. 10.5 to 30 VDC power input
J. Serial modbus
WARNING
Conduit/cable entries
The conduit/cable entries in the transmitter housing use a ½–14 NPT thread
form.When installing in a hazardous location, use only appropriately listed or
Ex certified plugs, glands, or adapters in cable/conduit entries.
March 2020 Quick Start Guide
Quick Start Guide 5

3.1 Establishing a connection
Connect the PC/laptop to the Ethernet 1 (Primary) receptacle on the
Gateway using an Ethernet cable.
3.2 Windows 7
Procedure
1. Click the Internet Access icon on the bottom right of the screen.
Figure 3-2: Internet Access
2. Select the Network and Sharing Center.
3. Select Local Area Connection.
Quick Start Guide March 2020
6 Emerson.com

Figure 3-3: Local Area Connection
4. Select Properties.
5. Select Internet Protocol Version 4 (TCP/IPv4) then select Properties.
Figure 3-4: Internet Protocol Version 4 (TCP/IPv4)
Note
If the PC/laptop is from another network, record the current IP
address and other settings so the PC/laptop can be returned to the
original network after the Gateway has been configured.
6. Select the Use the following IP address button.
March 2020 Quick Start Guide
Quick Start Guide 7

Figure 3-5: IP Address
7. In the IP address field, enter 192.168.1.12 (DeltaV Ready enter
10.5.255.12).
8. In the Subnet mask field, enter 255.255.255.0.
9. Select OK for both the Internet Protocol (TCP/IP) Properties window and
the Local Area Connection Properties window.
Quick Start Guide March 2020
8 Emerson.com

3.3 Windows 10
Figure 3-6: Network Settings
Procedure
1. Select the network icon in the lower right corner.
2. Select the Network settings link.
3. Select Change adapter options.
March 2020 Quick Start Guide
Quick Start Guide 9

Figure 3-7: Change Adapter Options
4. Right click the network interface connection that the Gateway is
plugged into, and select Properties.
5. Select Internet Protocol Version 4 (TCP/IPv4) then select Properties.
Quick Start Guide March 2020
10 Emerson.com

Figure 3-8: Internet Protocol Version 4 (TCP/IPv4)
Note
If the PC/laptop is from another network, record the current IP
address and other settings so the PC/laptop can be returned to the
original network after the Gateway has been configured.
6. Select the Use the following IP address button.
March 2020 Quick Start Guide
Quick Start Guide 11

Figure 3-9: IP Address
7. In the IP address field, enter 192.168.1.11 (DeltaV Ready enter
10.5.255.12).
8. In the Subnet mask field, enter 255.255.255.0.
9. Select OK for both the Internet Protocol (TCP/IP) Properties window and
the Local Area Connection Properties window.
Note
Connecting to the Gateway's secondary Ethernet port will require
different network settings.
Table 3-1: Network Settings
Gateway PC/laptop/
tablet
Subnet
Ethernet 1 192.168.1.10 192.168.1.12 255.255.255.0
Ethernet 2 192.168.2.10 192.168.2.12 255.255.255.0
Quick Start Guide March 2020
12 Emerson.com

3.4 Disable proxies
This procedure may be necessary when using a Chrome browser with
Windows operating systems.
Procedure
1. Open web browser.
2. Navigate Settings >Advanced.
3. In the System section, click Open proxy settings.
Example
3.5 Configure the Gateway
To complete initial configuration for the Gateway, follow the steps below.
This will have to be done be done for both networks.
Procedure
1. Access the default web page for the Gateway at https://
192.168.1.10.
a) Log on as Username: admin
b) Type in password: default
March 2020 Quick Start Guide
Quick Start Guide 13

Figure 3-10: User Name and Password
2. Navigate to System Settings > Gateway > Ethernet Communication to
enter the Network Settings.
a) Configure a static IP Address or set for DHCP and enter a
Hostname.
Figure 3-11: Ethernet Communication
b) Restart application at System Settings > Gateway > Backup and
Restore > Restart Apps.
Note
Resetting applications will temporarily disable communications with
field devices.
3. Disconnect the power and Ethernet cable from the Gateway.
Quick Start Guide March 2020
14 Emerson.com

4 Physical installation
4.1 Emerson 1410S2 mounting
Find a location where the Gateway has convenient access to the host system
network (process control network).
4.1.1 Pipe mount
Prerequisites
The following hardware and tools are needed to mount the Gateway to a 20-
in. pipe:
•Two 5/16-in. u-bolts (supplied with Gateway
•2-in. mounting pipe
•1/2-in. socket-head wrench
Procedure
1. Insert one u-bolt around the pipe, through the top mounting holes of
the Gateway mounting bracket, and through the washer plate.
2. Use a 1/2-in. socket-head wrench to fasten the nuts to the u-bolt.
3. Repeat for the second u-bolt and the lower mounting holes.
Figure 4-1: Emerson 1410S2 Mounting
March 2020 Quick Start Guide
Quick Start Guide 15

4.1.2 Bracket mount
The following hardware and tools are needed to mount the Gateway to a
support bracket:
Prerequisites
•Four 15/16-in. bolts
•Mounting support bracket
•⅜-in. drill
•½ -in. socket-head wrench
Mount the Gateway using the following procedure:
Procedure
1. Drill four 3/8-in. (9,525 mm) holes spaced 3.06-in. (77 mm) apart
horizontally and 11.15-in. (283 mm) apart vertically in the support
bracket, corresponding with the holes on the Gateway mounting
bracket.
2. Using a 1/2-in. socket-head wrench, attach the Gateway to the
support bracket with four 15/16-in. bolts.
Quick Start Guide March 2020
16 Emerson.com

4.2 Connecting the Emerson 1410S with 781S Smart
antennas
Figure 4-2: Emerson 1410S and 781S Installation
A. Emerson Wireless 1410S Gateway
B. Terminal connections
C. Shield pair cable
D. Emerson Wireless 781S Smart Antenna
E. Power output
F. RS-485 comm
G. 10.5 to 30 VDC power input
H. Serial modbus
Procedure
1. Attach shield pair cable.
2. Tape back shield wire and foils.
4.3 Emerson 1410S grounding
The Gateway enclosure case should always be grounded in accordance with
national and local electrical codes. The most effective grounding method is a
direct connection to earth ground with minimal impedance. Ground the
Gateway by connecting the external grounding lug to earth ground. The
connection should be 1Ω or less. The external ground plug is located on the
left side of the Gateway enclosure and is identified by the following symbol:
March 2020 Quick Start Guide
Quick Start Guide 17

4.4 Terminating resistors
Please reference the Emerson 1410S Gateway and 781S Smart Antenna
Reference Manual for configuration of the DIP switches.
Three DIP switches are provided to enable termination and biasing resistors
to the serial Modbus connection. The switches are found in the electronics
housing located above the terminal connections. The three DIP switches are
on the right side and the down position in ON.
4.5 Connect to the host system
Procedure
1. Wire the Gateway’s Ethernet 1 (Primary) or Serial Output connection
to the Host System Network or Serial I/O (see Figure 1 and Figure 2
for hardware drawings). This will have to be done for both networks.
You can route the networks to different locations if necessary.
2. For serial connections, make sure all terminations are clean and
secure to avoid wiring connection problems.
4.6 Best practice
Twisted shielded pair cable is generally used to wire the serial connection,
and it is standard practice to ground the shield on the serial host side leaving
the shield floating on the Gateway side. Insulate the shield to avoid
grounding issues.
In accordance with Emerson WirelessHART® security guidelines (Emerson
Wireless Security Whitepaper), the Gateway should be connected to the
Host System via a LAN (Local Area Network) and not a WAN (Wide Area
Network).
Quick Start Guide March 2020
18 Emerson.com

5 Software installation (optional)
5.1 Installation instructions
The 2-disk software pack contains the Security Setup Utility (only required
for secure host connections or OPC communications) and AMS Wireless
Configurator. The Security Setup Utility is located on Disk 1.
Procedure
1. Exit/close all Windows programs, including any running in the
background, such as virus scan software.
2. Insert Disk 1 into the CD/DVD drive of the PC.
3. If the setup program does not appear, go into the disk's file and run
autorun.exe.
4. Follow the prompts.
5. Insert Disk 2 into the CD/DVD drive of the PC.
6. Select Install from the menu when the AMS Wireless Configurator
setup begins.
7. Follow the prompts.
8. Allow AMS Wireless Configurator to reboot PC.
9. Do not remove the disk from the CD/DVD drive.
10. Installation will resume automatically after login.
11. Follow the prompts.
Note
If the autorun function is disabled on the PC, or installation does not
begin automatically, double click D:\SETUP.EXE (where D is the
CD/DVD drive on the PC) and select OK.
For more information about the Security Setup Utility and AMS
Wireless Configurator, see the Emerson 1410S Gateway and 781S
Smart Anetennas Reference Manual.
March 2020 Quick Start Guide
Quick Start Guide 19

6 Verify operations
Operation is verified through the web interface by opening a web browser
from any PC on the host system network and entering the Gateway IP
address or DHCP host name in the address bar. If the Gateway has been
connected and configured properly, the security alert will be displayed
followed by the log in screen. Thiswill need to be done for both networks.
Figure 6-1: Gateway Log In Screen
The Gateway is now ready to be integrated into the host system. Ensure the
field devices to be used with each network have the Network ID and Join Key
that is on the Gateway (found on the Network Setting page). Once the field
devices are powered, they will appear on the wireless network and
communications can be verified under the Explore tab using the web
interface. The time needed for the network to form will depend on the
number of devices.
Quick Start Guide March 2020
20 Emerson.com