Emerson Smart Wireless Gateway 1410 User manual

Quick Start Guide
00825-0200-4410, Rev CA
October 2014
Emerson Smart Wireless Gateway 1410
00825-0200-4410_CA.fm Page 1 Thursday, October 16, 2014 6:44 PM

October 2014
2
Quick Start Guide
NOTICE
This guide provides basic guidelines for the Emerson 1410 Smart Wireless Gateway. It does not
provide instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the
Emerson Smart Wireless Gateway 1410 Reference Manual (document number
00809-0200-4410) for more information and instructions. The manual and this guide are
available electronically on www.emersonprocess.com.
Explosion Hazard - Do not make or break any connections to the 1410 while circuits are live
unless area is known to be non-hazardous. Explosions could result in death or serious injury:
Installation of this device in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Please review the
Product Certifications section for any restrictions associated with a safe installation.
Avoid contact with the leads and terminals. High voltage that may be present on leads can
cause electrical shock. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following conditions. This device may not cause harmful interference. This device must
accept any interference received, including interference that may cause undesired operation.
This device must be installed to ensure a minimum antenna separation distance of 20 cm from
all persons.
Potential Electrostatic Charging Hazard
The 1410 enclosure is plastic. Use care in handling and cleaning when in explosive environments
to avoid an electrostatic discharge.
Contents
Wireless Considerations . . . . . . . . . . . . . . page 3
General considerations . . . . . . . . . . . . . . . page 3
Initial connection and configuration . . . page 4
Physical installation . . . . . . . . . . . . . . . . . . page 9
Software installation (optional) . . . . . . page 13
Verify operations . . . . . . . . . . . . . . . . . . . page 14
Product Certification . . . . . . . . . . . . . . . . page 15
Declaration of Conformity . . . . . . . . . . . page 17
00825-0200-4410_CA.fm Page 2 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
3
October 2014
Wireless Considerations
Power up sequence
The Emerson Smart Wireless Gateway 1410 (Gateway) should be installed and
functioning properly before Power Modules are installed in any wireless field
devices. Wireless field devices should also be powered up in order of proximity
from the Gateway beginning with the closest. This will result in a simpler and
faster network installation.
Antenna position
The antenna should be positioned vertically, and be approximately 6 ft. (2 m)
from large structures or buildings to allow for clear communication to other
devices.
Mounting height
For optimal wireless coverage, the remote antenna is ideally mounted 15 - 25 ft.
(4.6 - 7.6 m) above ground or 6 ft. (2 m) above obstructions or major
infrastructure.
General considerations
PC requirements
Operating System (optional software only)
Windows™XP Professional, Service Pack 3
Windows Server 2003 Service Pack 2
Windows Server 2003 R2 Service Pack 2
Windows Server 2008 (Standard Edition), Service Pack 2
Windows Server 2008 R2 Standard Edition, Service Pack 1
Windows 7 Professional, Service Pack 1
Windows 7 Enterprise, Service Pack 1
Windows 8 Enterprise, Service Pack 1
Applications
Internet Explorer®6.0 - 10.0
Hard Disk Space
AMS™Wireless Configurator: 1.5 GB
Gateway Setup CD: 250 MB
00825-0200-4410_CA.fm Page 3 Thursday, October 16, 2014 6:44 PM

October 2014
4
Quick Start Guide
Step 1: Initial connection and configuration
To configure the Emerson Smart Wireless Gateway 1410, a local connection
between a PC/Laptop and the Gateway needs to be established. The 1410 and the
1410D are operationally equivalent and the following instructions are applicable
to both models.
Powering the gateway
Bench top power will be needed to power the Gateway by wiring a 24 VDC
(nominal) power source, with at least 250 mA, to the power terminals.
Figure 1. 1410 Housing Diagram
A. DIN Rail clip
B. SMA to N type connection
C. Power and Reset indicator lights. During normal operation the power indicator will be green.
During a reset the reset light will turn red. The reset switch should not be enabled during normal
operation.
D. Ethernet port 2. This secondary port must be enabled when ordering to access the device.
When this port is activated, the factory IP address is 192.168.2.10. See Table 1 on page 6.
E. Ethernet port 1. Use for standard communication to the webserver or other protocols enabled
on the gateway. The factory IP address is 192.168.1.10. See Table 1 on page 6.
F. 5-screw analog terminal block female. Black terminal block included in the box.
+-AB
24 VDC
(nominal)
Power Input
Serial
Modbus
S
Power
Reset
A
B
C
D
E
F
00825-0200-4410_CA.fm Page 4 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
5
October 2014
Figure 2. 1410D Wiring Diagram
A. 1410 Power and Serial Connections
B. Smart Wireless Field Link Power and Data Connections
Establishing a connection
1. Connect the PC/Laptop to the Ethernet 1 (Primary) receptacle on the Gateway
using an Ethernet cable.
2. To establish the PC/Laptop settings begin with Start>Settings>Network
Connections.
a. Select Local Area Connection.
00825-0200-4410_CA.fm Page 5 Thursday, October 16, 2014 6:44 PM

October 2014
6
Quick Start Guide
b. Right click to select Properties.
c. Select Internet Protocol (TCP/IP), then select the Properties button.
Note
If the PC/laptop is from another network, record the current IP address and other settings so the
PC/laptop can be returned to the original network after the Gateway has been configured.
d. Select the Use the following IP address button
e. In the IP address field, enter 192.168.1.12.
f. In the Subnet mask field, enter 255.255.255.0.
g. Select OK for both the Internet Protocol (TCP/IP) Properties window and the
Local Area Connection Properties window.
Note
Connecting to the Gateway's secondary Ethernet port will require different network settings.
3. Disable proxies.
a. Open a standard web browser
b. Navigate Tools>Internet Options>Connections>LAN Settings
c. Under Proxy server, uncheck the Use a proxy server... box.
Table 1. TCP/IP Network Settings
Gateway PC/laptop Subnet
Ethernet 1 192.168.1.10 192.168.1.12 255.255.255.0
Ethernet 2 192.168.2.10 192.168.2.12 255.255.255.0
00825-0200-4410_CA.fm Page 6 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
7
October 2014
Configure the Emerson Smart Wireless Gateway 1410
To complete initial configuration for the gateway:
1. Access the default web page for the Gateway at https://192.168.1.10.
a. Log on as User: admin
b. Type in password: default
00825-0200-4410_CA.fm Page 7 Thursday, October 16, 2014 6:44 PM

October 2014
8
Quick Start Guide
2. Navigate to Setup>Ethernet Protocol>Address to enter the Network Settings.
a. Configure a static IP Address or set for DHCP and enter a Hostname.
b. Restart application at Setup>Restart Apps.
Note
Resetting applications will temporarily disable communications with field devices.
3. Disconnect the power and Ethernet cable from the Gateway.
Table 2. Network Settings
Gateway PC/laptop Subnet
Ethernet 1 192.168.1.10 192.168.1.12 255.255.255.0
Ethernet 2 192.168.2.10 192.168.2.12 255.255.255.0
00825-0200-4410_CA.fm Page 8 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
9
October 2014
Step 2: Physical installation
Remote antenna
The remote antenna options provide flexibility for mounting the Gateway based
on wireless connectivity, lightning protection, and current work practices.
The remote mount antenna kit includes coaxial sealant for the cable connections,
for the lightning arrestor, and for the antenna.
Find a location where the remote antenna has optimal wireless performance.
Ideally this will be 15-25 ft (4.6 - 7.6 m) above the ground or 6 ft (2 m) above
obstructions or major infrastructure. To install the remote antenna use one of the
following procedures:
Installation of WL2/WN2 option:
1. Mount the antenna on a 1.5-2 inch pipe mast using the supplied mounting
equipment.
2. Connect the lightning arrestor directly to the enclosure.
3. Install the grounding lug, lock washer, and nut on top of the lightning arrestor.
4. Connect the antenna to the lightning arrestor using the supplied coaxial cable
ensuring the drip loop is not closer than 1 foot (0.3 m) from the lightning
arrestor.
5. Use the coaxial sealant to seal each connection between the wireless field
device, lightning arrestor, cable, and antenna.
6. Ensure the mounting mast, lightning arrestor, and Gateway are grounded
according to local/national electrical code.
Any spare lengths of coaxial cable should be placed in 1 foot (0.3 m) coils.
When installing remote mount antennas for the Emerson 1410 Smart Wireless Gateway, always
use established safety procedures to avoid falling or contact with high-power electrical lines.
Install remote antenna components for the Emerson 1410 Smart Wireless Gateway in
compliance with local and national electrical codes and use best practices for lightning
protection.
Before installing, consult with the local area electrical inspector, electrical officer, and work area
supervisor.
The Emerson Smart Wireless Gateway 1410 remote antenna option is specifically engineered to
provide installation flexibility while optimizing wireless performance and local spectrum
approvals. To maintain wireless performance and avoid non-compliance with spectrum
regulations, do not change the length of cable or the antenna type.
If the supplied remote mount antenna kit is not installed per these instructions, Emerson
Process Management is not responsible for wireless performance or non-compliance with
spectrum regulations.
00825-0200-4410_CA.fm Page 9 Thursday, October 16, 2014 6:44 PM

October 2014
10
Quick Start Guide
Figure 3. Installation of WL2/WN2 Option
Note: Weather proofing is required
The remote mount antenna kit includes coaxial sealant for the cable connections for the lightning
arrestor, antenna, and Gateway. The coaxial sealant must be applied to guarantee performance of
the wireless field network. See Figure 4 for details on how to apply weather proofing.
Figure 4. Applying Coaxial Sealant to Cable Connections
Note
For installing the Smart Wireless Field Link, see reference document 00825-0100-4421.
Table 3. Remote Antenna Kit Options
Kit option Antenna Cable 1 Cable 2 Lightning arrestor
WL2
1/2Wavelength Dipole
Omni-Directional
+6 dB Gain
50 ft. (15,2 m)
LMR-400 N/A
Head mount, jack to plug
Gas discharge tube
0.5 dB insertion loss
WN2
1/2Wavelength Dipole
Omni-Directional
+8 dB Gain
25 ft. (7,6 m)
LMR-400 N/A Head mount, jack to plug Gas discharge tube
0.5 dB insertion loss
00825-0200-4410_CA.fm Page 10 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
11
October 2014
Connect to the host system
1. Wire the Gateway’s Ethernet 1 (Primary) or Serial Output connection to the
Host System Network or Serial I/O.
2. For Serial connections, connect A to A, B to B, making sure all terminations are
clean and secured to avoid wiring connection problems.
Figure 5. 1410 Wiring Diagram
A. 5-screw terminal block
+-AB
24 VDC
(nominal)
Power Input
Serial
Modbus
S
Power
Reset
A
00825-0200-4410_CA.fm Page 11 Thursday, October 16, 2014 6:44 PM

October 2014
12
Quick Start Guide
Figure 6. 1410D Housing Diagram
A. DIN Rail clip
B. Power and Reset indicator lights. During normal operation the power indicator will be green.
During a reset the reset light will turn red. The reset switch should not be enabled during normal
operation.
C. Ethernet port 2. Must have this port enabled when ordered to access. The factory IP address is
192.168.2.10. See Table 2 on page 8.
D. Ethernet port 1. Use for standard communication to the webserver or other protocols enabled
on the gateway. The factory IP address is 192.168.1.10. See Table 2 on page 8.
E. 5-screw analog terminal blocks female for power and field link connection. See below for the
wiring diagram of the included male connectors.
Best practice
Twisted shielded pair cable is generally used to wire the Serial connection, and it
is standard practice to ground the shield on the Serial Host side leaving the shield
floating on the Gateway side. To avoid grounding issues be sure to insulate the
shield.
Power
Wire a 24 VDC (nominal) Class 2 power source, with at least 250 mA of current, to
the power terminals using the Gateway Terminal Block Diagram shown in Figure 5.
00825-0200-4410_CA.fm Page 12 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
13
October 2014
Step 3: Software installation (optional)
The 2 disk software pack contains the Security Setup Utility (only required for
secure host connections or OPC communications) and AMS Wireless
Configurator. The Security Setup Utility is located on Disk 1. To install the
software:
1. Exit/close all Windows programs, including any running in the background,
such as virus scan software.
2. Insert Disk 1 into the CD/DVD drive of the PC.
3. Follow the prompts.
AMS Wireless Configurator is located on Disk 2. To install the software:
1. Exit/close all Windows programs, including any running in the background,
such as virus scan software.
2. Insert Disk 2 into the CD/DVD drive of the PC.
3. Select Install from the menu when the AMS Wireless Configurator setup
begins.
4. Follow the prompts.
5. Allow AMS Wireless Configurator to reboot PC.
6. Do not remove the disk from the CD/DVD drive.
7. Installation will resume automatically after login.
8. Follow the prompts.
Note
If the autorun function is disabled on the PC, or installation does not begin automatically, double
click D:\SETUP.EXE (where D is the CD/DVD drive on the PC) and select OK.
For more information about the Security Setup Utility and AMS Wireless
Configurator, see the Emerson Smart Wireless Gateway 1410 Reference Manual
(document number 00809-0200-4410).
Note
For information on how to connect with a Windows 7 PC, please see the Gateway overview
supplement (document number 00840-0900-4420).
00825-0200-4410_CA.fm Page 13 Thursday, October 16, 2014 6:44 PM

October 2014
14
Quick Start Guide
Step 4: Verify operations
Operation is verified through the web interface by opening a web browser from
any PC on the host system network and entering the Gateway IP address or DHCP
host name in the address bar. If the Gateway has been connected and configured
properly, the security alert will be displayed followed by the log in screen.
Figure 7. Gateway Log In Screen
The Gateway is now ready to be integrated into the host system. If wireless field
devices were ordered with the Gateway, they were preconfigured with the same
Network ID and Join Key information. Once the field devices are powered, they
will appear on the wireless network and communications can be verified under
the Explore tab using the web interface. The time needed for the network to form
will depend on the number of devices.
For more detailed installation instructions, see the Emerson Smart Wireless
Gateway 1410 Reference Manual (document number 00809-0200-4410).
00825-0200-4410_CA.fm Page 14 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
15
October 2014
Product Certification
Approved Manufacturing Locations
Rosemount Inc. - Chanhassen, Minnesota, USA
Emerson Process Management Asia Pacific Private Limited - Singapore
Telecommunication Compliance
All wireless devices require certification to ensure that they adhere to regulations
regarding the use of the RF spectrum. Nearly every country requires this type of
product certification. Emerson is working with governmental agencies around
the world to supply fully compliant products and remove the risk of violating
country directives or laws governing wireless device usage.
FCC and IC
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following conditions: This device may not cause harmful interference. This device
must accept any interference received, including interference that may cause
undesired operation. This device must be installed to ensure a minimum antenna
separation distance of 20 cm from all persons.
European Directive Information
The EC declaration of conformity can be found on page xx. The most recent
revision can be found at www.emersonprocess.com.
Ordinary Location Certification from FM Approvals
As standard, the transmitter has been examined and tested to determine that the
design meets basic electrical, mechanical, and fire protection requirements by FM
Approvals, a nationally recognized testing laboratory (NRTL) as accredited by the
Federal Occupational Safety and Health Administration (OSHA).
Hazardous Locations Certifications
North America
N5 FM Approvals, Nonincendive for Class I Division 2
Certificate: 3049590
Standards Used: Class 3600:2011, Class 3611:2004, Class 3810:2005
Markings: NI CL I, DIV. 2, GP A, B, C, D
Temperature code: T4 (-40 °C ≤Ta≤ 60 °C)
Special Condition for Safe Use (X):
1. When installed as Division 2 equipment, the 1410 shall be mounted within a
tool-secured enclosure which meets the requirements of ANSI/ISA 61010-1 and be
capable of accepting the applicable wiring methods per the NEC.
00825-0200-4410_CA.fm Page 15 Thursday, October 16, 2014 6:44 PM

October 2014
16
Quick Start Guide
N6 CSA Class I Division 2
Certificate: 2646342
Standards Used: CSA Std. C22.2 No. 0-10, CSA Std. C22.2 No. 213 - M1987,
CSA Std. C22.2 No.61010-1-12, ANSI/ISA 12.12.01-2012, ANSI/ISA
61010-1-2012
Markings: SUITABLE FOR CL I, DIV. 2, GP A, B, C, D
Temperature code: T4 (-40 °C ≤ Ta≤70 °C)
Note
Shall be powered by a class 2 power supply.
Suitable for dry indoor locations only.
Equipment must be installed in a suitable tool accessible enclosure subject to the end
use application.
Using the 1410D and the Smart Wireless Field Link 781 in a hazardous location requires
barriers between the two units.
00825-0200-4410_CA.fm Page 16 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
17
October 2014
Declaration of Conformity
00825-0200-4410_CA.fm Page 17 Thursday, October 16, 2014 6:44 PM

October 2014
18
Quick Start Guide
00825-0200-4410_CA.fm Page 18 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
19
October 2014
00825-0200-4410_CA.fm Page 19 Thursday, October 16, 2014 6:44 PM

Quick Start Guide
00825-0200-4410, Rev CA
October 2014
?00825-0200-4410?
00825-0200-4410, Rev CA, 10/14
Emerson Process Management
Rosemount Inc.
8200 Market Boulevard
Chanhassen, MN USA 55317
T (US) [phone]
T (Intnl) [phone]
F [phone]
Emerson Process Management
Latin America
1300 Concord Terrace, Suite 400
Sunrise Florida 33323 USA
Tel + 1 954 846 5030
www.rosemount.com
Emerson Process Management
Asia Pacific Private Limited
1 Pandan Crescent
Singapore 128461
T (65) 6777 8211
F (65) 6777 0947/65 6777 0743
Emerson Process Management
GmbH & Co. OHG
Argelsrieder Feld 3
82234 Wessling Germany
T 49 (8153) 9390, F49 (8153) 939172
Beijing Rosemount Far East
Instrument Co., Limited
No. 6 North Street, Hepingli,
Dong Cheng District
Beijing 100013, China
T (86) (10) 6428 2233
F (86) (10) 6422 8586
© 2014 Rosemount Inc. All rights reserved. All marks property of owner.
The Emerson logo is a trade mark and service mark of Emerson Electric Co.
AMS, Rosemount, and the Rosemount logotype are registered trademarks of
Rosemount Inc.
Internet Explorer and Windows are registered trademarks of Microsoft Corporation
in the United States and other countries.
00825-0200-4410_CA.fm Page 20 Thursday, October 16, 2014 6:44 PM