Emerson Micro Motion 5700 User manual

Installation Manual
MMI-20029768, Rev AG
November2023
Micro Motion™ 5700 Ethernet
Transmitters
Ethernet Installations

Safety messages
Safety messages are provided throughout this manual to protect personnel and equipment. Read each safety
message carefully before proceeding to the next step.
Safety and approval information
This Micro Motion product complies with all applicable European directives when properly installed in accordance
with the instructions in this manual. Refer to the EU Declaration of Conformity for directives that apply to this
product. The following are available: the EU Declaration of Conformity, with all applicable European directives, and the
complete ATEX installation drawings and instructions. In addition, the IECEx installation instructions for installations
outside of the European Union and the CSA installation instructions for installations in North America are available at
Emerson.com or through your local Micro Motion support center.
Information affixed to equipment that complies with the Pressure Equipment Directive, can be found at
Emerson.com. For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not
apply.
Other information
Troubleshooting information can be found in the appropriate Configuration and Use Manual. Product data sheets and
manuals are available from the Micro Motion website at Emerson.com.
Return policy
Follow Emerson procedures when returning equipment. These procedures ensure legal compliance with government
transportation agencies and help provide a safe working environment for Emerson employees. If you fail to follow
Emerson procedures, then Emerson will not accept your returned equipment.
Return procedures and forms are available on our web support site at Emerson.com, or by calling the Micro Motion
Customer Service department.
2

Contents
Chapter 1 Before you begin....................................................................................................................... 5
1.1 About this document.................................................................................................................. 5
1.2 Hazard messages........................................................................................................................ 5
1.3 Related documentation.............................................................................................................. 6
Chapter 2 Planning..................................................................................................................................... 7
2.1 Installation checklist....................................................................................................................7
2.2 Additional considerations for retrofitting existing installations........................................... 8
2.3 Power requirements................................................................................................................... 9
2.4 5700 transmitters in Ethernet networks................................................................................ 10
Chapter 3 Mounting and sensor wiring................................................................................................. 15
3.1 Mounting and sensor wiring for integral-mount transmitters........................................... 15
3.2 Mounting transmitters............................................................................................................. 15
3.3 Wire a remote-mount transmitter to the sensor.................................................................. 19
3.4 Ground the meter components...............................................................................................22
3.5 Rotate the transmitter on the sensor (optional)................................................................... 23
3.6 Rotate the user interface on the transmitter (optional).......................................................25
3.7 Rotate the sensor wiring junction box on a remote-mount transmitter (optional)..........26
Chapter 4 Wiring the channels................................................................................................................29
4.1 Available channels.....................................................................................................................29
4.2 Wire the I/O channel.................................................................................................................29
4.3 Wire the Ethernet channels......................................................................................................35
Chapter 5 Power supply wiring............................................................................................................... 39
5.1 Wiring the power supply.......................................................................................................... 39
5.2 Wire the power supply using an M12-terminated cable (optional).................................... 40
Chapter 6 Set up the printer....................................................................................................................41
6.1 Set up the printer by changing the printer default IP address........................................... 41
6.2 Set up the printer using the printer default IP address....................................................... 43
6.3 Reset the interface settings..................................................................................................... 44
6.4 Function Check Failed............................................................................................................... 44
Chapter 7 Power up the transmitter...................................................................................................... 47
Chapter 8 Guided setup............................................................................................................................49
Chapter 9 Using the display controls..................................................................................................... 51
Chapter 10 Available service port connection.........................................................................................53
Appendix A Wire the 5700 to the 3100 relays........................................................................................... 55
Installation Manual Contents
MMI-20029768 November2023
Installation Manual 3

Contents Installation Manual
November2023 MMI-20029768
4 Micro Motion 5700 Ethernet Transmitters

1 Before you begin
1.1 About this document
This manual provides information on planning, mounting, wiring, and initial setup
of the Micro Motion transmitter. For information on full configuration, maintenance,
troubleshooting, or service of the transmitter, see the Micro Motion 5700 with Ethernet
Transmitters: Configuration and Use Manual.
The information in this document assumes that users understand basic transmitter and
sensor installation, configuration, and maintenance concepts and procedures.
1.2 Hazard messages
This document uses the following criteria for hazard messages based on ANSI standards
Z535.6-2011 (R2017).
DANGER
Serious injury or death will occur if a hazardous situation is not avoided.
WARNING
Serious injury or death could occur if a hazardous situation is not avoided.
CAUTION
Minor or moderate injury will or could occur if a hazardous situation is not avoided.
NOTICE
Data loss, property damage, hardware damage, or software damage can occur if a
situation is not avoided. There is no credible risk of physical injury.
Physical access
WARNING
Unauthorized personnel can potentially cause significant damage and/or
misconfiguration of end users' equipment. Protect against all intentional or unintentional
unauthorized use.
Physical security is an important part of any security program and fundamental to
protecting your system. Restrict physical access to protect users' assets. This is true for all
systems used within the facility.
Installation Manual Before you begin
MMI-20029768 November2023
Installation Manual 5

1.3 Related documentation
You can find all product documentation on the product documentation DVD shipped with
the product or at Emerson.com.
See any of the following documents for more information:
•Micro Motion 5700 Transmitters Product Data Sheet
•Micro Motion 5700 with Ethernet Transmitters: Configuration and Use Manual
•Micro Motion 5700 Transmitters: EtherNet/IP Rockwell RSLogix Integration Guide
•Micro Motion 5700 Transmitters: PROFINET Siemens PLC Integration Guide
•Sensor installation manual
Before you begin Installation Manual
November2023 MMI-20029768
6 Micro Motion 5700 Ethernet Transmitters

2 Planning
2.1 Installation checklist
□If possible, install the transmitter in a location that will prevent direct exposure to
sunlight. The environmental limits for the transmitter may be further restricted by
hazardous area approvals.
□If you plan to mount the transmitter in a hazardous area:
WARNING
—Verify that the transmitter has the appropriate hazardous area approval. Each
transmitter has a hazardous area approval tag attached to the transmitter
housing.
—Ensure that any cable used between the transmitter and the sensor meets the
hazardous area requirements.
—For ATEX/IECEx installations, strictly adhere to the safety instructions documented
in the ATEX/IECEx approvals documentation available on the product
documentation DVD shipped with the product or at Emerson.com.
□Verify that you have the appropriate cable and required cable installation parts for your
installation. For wiring between the transmitter and sensor, verify the maximum cable
length does not exceed 1,000ft (305m).
□Ensure that you use the following cables for the different connections:
—A twisted-pair instrument cable for the Channel I/O connection
—A shielded Cat5E or higher rated instrumentation cable for the Ethernet connections
□You can mount the transmitter in any orientation as long as the conduit openings do
not point upward.
Installing the transmitter with the conduit openings facing upward risks condensation
moisture entering the transmitter housing, which could damage the transmitter.
Following are examples of possible orientations for the transmitter.
Preferred orientation Alternate orientations
□Any fittings, adapters, or blanking elements used on either conduit entries or threaded
joints that are a part of flame proof joints must comply with the requirements of EN/IEC
60079-1 & 60079-14 or CSA C22.2 No 30 & UL 1203 for Europe/International and North
America respectively.
Only qualified personnel can select and install these elements in accordance with
EN/IEC 60079-14 for ATEX/IECEx or to NEC/CEC for North America.
Installation Manual Planning
MMI-20029768 November2023
Installation Manual 7

□To maintain the Ingress protection thread sealant, a sealing washer, or O-ring must be
applied:
—For Zone 1 applications, thread sealant must also comply with the requirements of
EN/IEC 60079-14 and thus must be non-setting, non-metallic, non-combustible, and
maintain earthing between the equipment and conduit.
—For Class I, Groups A, B, C, and D applications, thread sealant must also comply with
the requirements of UL 1203/CSA C22.2 No. 30.
□Mount the meter in a location and orientation that satisfies the following conditions:
—Allows sufficient clearance to open the transmitter housing cover. Install with 8in
(203mm) to 10in (254mm) clearance at the wiring access points.
—Provides clear access for installing cabling to the transmitter.
—Provides clear access to all wiring terminals for troubleshooting.
2.2 Additional considerations for retrofitting
existing installations
□The transmitter installation may require 3in (76mm) to 6in (152mm) of additional
wiring for the input/output and power connections. This length would be in addition to
the currently installed wiring. Confirm you have the additional wiring necessary for the
new installation.
□Before removing the existing transmitter, be sure to record the configuration data for
the currently installed transmitter. At initial startup of the newly installed transmitter,
you will be prompted to configure the meter via a guided setup.
Record the following information (if applicable):
Variable Setting
Tag
Mass flow units
Volume flow units
Density units
Temperature units
Channel configuration
mA Output 1 —Power (internal or external)
—Source
—Scaling (LRV, URV)
—Fault action
mA Output 2 (optional) —Power (internal or external)
—Source
—Scaling (LRV, URV)
—Fault action
Planning Installation Manual
November2023 MMI-20029768
8 Micro Motion 5700 Ethernet Transmitters

Variable Setting
Frequency output (optional) —Power (nternal or external)
—Source
—Scaling (LRV, URV)
—Fault action
—Dual output
Discrete output (optional) —Power (internal or external)
—Source
—Scaling (LRV, URV)
—Fault action
Discrete input (optional) —Power (internal or external)
—Source
—Scaling (LRV, URV)
—Fault action
Calibration parameters (for 9-wire installations only)
Flow calibration factor FCF (Flow cal or flow calibration factor):
Density calibration factors —D1
—D2
—K1
—K2
—TC
—FD
2.3 Power requirements
Self-switching AC/DC input, automatically recognizes supply voltage:
•85 to 240 VAC, 6.5 watts typical, 9 watts maximum
•18 to 100 VDC, 6.5 watts typical, 9 watts maximum
Note
For DC power:
•Power requirements assume a single transmitter per cable.
•At start-up, the power source must provide a minimum of 1.5 amps of short-term
current per transmitter and not pull voltage below 18 VDC.
•Length and conductor diameter of the power cable must be sized to provide 18 VDC
minimum at the power terminals, at a load current of 0.7 amps.
Cable sizing formula
M = 18V + (R x L x 0.7A)
•M: minimum supply voltage
Installation Manual Planning
MMI-20029768 November2023
Installation Manual 9

•R: cable resistance
•L: cable length (in Ω/ft)
Typical power cable resistance at 68°F (20.0°C)
Wire gauge Resistance
14 AWG 0.0050 Ω/ft
16 AWG 0.0080 Ω/ft
18 AWG 0.0128 Ω/ft
20 AWG 0.0204 Ω/ft
2.5 mm20.0136 Ω/m
1.5 mm20.0228 Ω/m
1.0 mm20.0340 Ω/m
0.75 mm20.0460 Ω/m
0.50 mm20.0680 Ω/m
2.3.1 Maximum cable lengths between sensor and transmitter
The maximum cable length between the sensor and transmitter, which are installed
separately, is determined by cable type.
Cable type Wire gauge Maximum length
MicroMotion 4-wire remote
mount
Not applicable •1,000ft (305m) without Ex-
approval
•500ft (152m) with IIC rated
sensors
•1,000ft (305m) with IIB
rated sensors
MicroMotion 9-wire remote
mount
Not applicable 1,000ft (305m)(1)
User-supplied 4-wire VDC 22AWG (0.326mm²) 300ft (91m)
VDC 20AWG (0.518mm²) 500ft (152m)
VDC 18AWG (0.823mm²) 1,000ft (305m)
RS-485 22AWG (0.326mm²) or
larger
1,000ft (305m)
(1) For Smart Meter Verification, the limit is 60ft (18m).
2.4 5700 transmitters in Ethernet networks
You can install the 5700 Ethernet transmitter in star, ring, or daisy-chain networks using
industrial-rated shielded Ethernet cables.
•Make sure that each cable is no longer than 328ft (100m).
•Connect the 5700 Ethernet transmitter to the host system via a LAN (Local Area
Network) and not a WAN (Wide Area Network).
•Follow all network security best practices.
Planning Installation Manual
November2023 MMI-20029768
10 Micro Motion 5700 Ethernet Transmitters

2.4.1 Star topology
5700 Ethernet transmitters can be installed in a star network.
Figure 2-1: 5700 star network
A. Programmable Logic Controller (PLC)
B. 5700 with Ethernet output
C. External Ethernet switch
Note
The External Ethernet switch must be a managed switch capable of Spanning Tree Protocol
(STP) or similar functions.
Installation Manual Planning
MMI-20029768 November2023
Installation Manual 11

2.4.2 Ring topology
5700 Ethernet transmitters can be installed in a ring network.
Figure 2-2: 5700 ring network
A. Programmable Logic Controller (PLC)
B. 5700 with Ethernet output
Note
The PLC must be a managed switch capable of Spannng Tree Protocol (STP) or similar
functions.
Planning Installation Manual
November2023 MMI-20029768
12 Micro Motion 5700 Ethernet Transmitters

2.4.3 Daisy-chain topology
5700 Ethernet transmitters can be installed in a daisy-chain network.
Figure 2-3: 5700 daisy-chain network
A. Programmable Logic Controller (PLC)
B. 5700 with Ethernet output
Installation Manual Planning
MMI-20029768 November2023
Installation Manual 13

Planning Installation Manual
November2023 MMI-20029768
14 Micro Motion 5700 Ethernet Transmitters

3 Mounting and sensor wiring
3.1 Mounting and sensor wiring for integral-mount
transmitters
There are no separate mounting requirements for integral transmitters, and there is no
need to connect wiring between the transmitter and the sensor.
3.2 Mounting transmitters
There are two options available for mounting 5700 transmitters:
•Mount the transmitter to a wall or flat surface.
•Mount the transmitter to an instrument pole.
3.2.1 Mount the transmitter to a wall or flat surface
Prerequisites
•Emerson recommends 5/16-18 (M8X1.25) fasteners that can withstand the process
environment. Emerson does not supply bolts or nuts as part of the standard offering
(general purpose bolts and nuts are available as an option).
•Ensure that the surface is flat and rigid and that it does not vibrate or move excessively.
•Confirm that you have the necessary tools and the mounting kit shipped with the
transmitter.
•Confirm that the mounting surface, method, and surface structure ensures sufficient
strength to secure the transmitter (e.g. when mounting to drywall use a toggle type
drywall anchor).
Procedure
1. Attach the mounting bracket to the transmitter and tighten the screws to 80in lbf
(9.04N m) to 90in lbf (10.17N m).
Installation Manual Mounting and sensor wiring
MMI-20029768 November2023
Installation Manual 15

Figure 3-1: Mounting bracket to an aluminum transmitter
Figure 3-2: Mounting bracket to a stainless steel transmitter
2. For wall-mount installations, secure the mounting bracket to the prepared surface.
Mounting and sensor wiring Installation Manual
November2023 MMI-20029768
16 Micro Motion 5700 Ethernet Transmitters

Figure 3-3: Wall-mounting bracket and dimensions for an aluminum
transmitter
A. 2.8in (71mm)
B. 2.8in (71mm)
Figure 3-4: Wall-mounting bracket and dimensions for a stainless steel
transmitter
A. 7.51in (190.8mm)
B. 3.67in (93.2mm)
Installation Manual Mounting and sensor wiring
MMI-20029768 November2023
Installation Manual 17

3. For aluminum transmitters, place and attach the transmitter-mounting bracket to
the mounting bracket secured to the wall or instrument pole.
Figure 3-5: Attaching and securing an aluminum transmitter to the mounting
bracket
Tip
To ensure the mounting bracket holes are aligned, insert all attachment bolts into
place before tightening.
3.2.2 Mount the transmitter to a pole
Prerequisites
•Ensure that the instrument pole extends at least 12in (305mm) from a rigid base and is
no more than 2in (51mm) in diameter.
•Confirm that you have the necessary tools, and the instrument-pole mounting kit
shipped with the transmitter.
Procedure
For pole-mount installations, fit the U-bolt mounting piece to the instrument pole.
Mounting and sensor wiring Installation Manual
November2023 MMI-20029768
18 Micro Motion 5700 Ethernet Transmitters

Figure 3-6: Pole-mounting bracket attachment for an aluminum transmitter
Figure 3-7: Pole-mounting bracket attachment for a stainless steel transmitter
3.3 Wire a remote-mount transmitter to the sensor
Use this procedure to wire a 4-wire or 9-wire remote-mount transmitter to the sensor.
Prerequisites
•Prepare the 9-wire cable as described in the Micro Motion 9-Wire Flow Meter Cable
Preparation and Installation Guide.
•Connect the cable to the sensor-mounted core processor or junction box as described
in the sensor documentation. You can access all product documentation on the
documentation DVD shipped with the product or at Emerson.com.
Installation Manual Mounting and sensor wiring
MMI-20029768 November2023
Installation Manual 19

Procedure
1. Remove the transmitter-to-sensor wiring compartment cover to reveal the terminal
connections.
Figure 3-8: Removal of the transmitter-to-sensor wiring compartment cover
2. Feed the sensor wiring cable into the transmitter wiring compartment.
Figure 3-9: Sensor wiring feedthrough
3. Connect the sensor wires to the appropriate terminals.
Important
Terminate the 4-wire cable drain wires only at the sensor/core processor end of the
cable. See the sensor installation manual for more detail. Do not connect the 4-wire
cable drain wires to the ground screw located inside the junction box.
•See Figure 3-10 for 4-wire terminal connections.
Mounting and sensor wiring Installation Manual
November2023 MMI-20029768
20 Micro Motion 5700 Ethernet Transmitters