Emerson Rosemount HART Modbus VeriCase 3308 Series User manual

Quick Start Guide
00825-0500-4530, Rev AD
April 2019
Rosemount™ VeriCase User Guide
Rosemount 3308 and 5300 Series Level
Transmitters with HART® and Modbus®

Contents
Overview......................................................................................................................................3
Check contents and verification sheet.......................................................................................... 4
Verify the Rosemount 3308 transmitter....................................................................................... 6
Verify the Rosemount 5300 transmitter..................................................................................... 10
Generate a report.......................................................................................................................13
FAQs.......................................................................................................................................... 14
Quick Start Guide April 2019
2 Rosemount VeriCase

1 Overview
The Rosemount™ VeriCase is a mobile verification tool for the Rosemount
3308 and 5300 Level Transmitters with HART® and Modbus®
communications.
The Rosemount VeriCase accuracy is within ±1 mm.
Figure 1-1 identifies the parts inside the case that you should be familiar with
before performing verification.
Note
The Rosemount VeriCase does not have any hazardous approvals
certifications and should only be used outside of such classified areas.
Figure 1-1: Rosemount VeriCase
A
C
D
B
G
F
E
A. Transmitter mount
B. Terminal connections
C. Cable switch
D. Temperature display
E. Power input
F. Ground connection
G. USB cable connection
April 2019 Quick Start Guide
Quick Start Guide 3

2 Check contents and verification sheet
2.1 Check contents
Procedure
Open the Rosemount VeriCase and check that it contains the following
items:
•USB stick containing
•User Instructions
•Microsoft® Excel® workbook
•Calibration certificate
•HART modem drivers
•Rosemount Radar Master (for Rosemount 5300 Level Transmitter)
•Instrument Inspector Application™ (for Rosemount 3308 Wireless Level
Transmitter)
•Printed calibration parameters
•Printed certificate
•110/220V Power Supply
•12 VDC Power Cable
•USB A-B cable
•Two terminal connection cables with banana plugs and grippers
2.2 Check the verification sheet
Procedure
1. Open the Excel workbook found on the USB memory stick.
2. Check that the following details in the workbook correspond to the
printed certificate found inside the Rosemount Vericase:
•Serial number and calibration date
•Cable lengths
•Values for temperature correction table
Quick Start Guide April 2019
4 Rosemount VeriCase

2.3 Power up the Rosemount VeriCase
The Rosemount VeriCase can be powered by either a 110V/220V power
supply or a 12VDC power adapter supplied with the Rosemount VeriCase. To
power up the Rosemount VeriCase and connect it to a transmitter head:
Procedure
1. Connect the power cable.
2. Screw the transmitter firmly onto the mount of the faceplate.
3. Insert the terminal connectors in the + and – terminals on the
faceplate and attach the other ends to the terminals of the
transmitter.
4. Connect the USB A-B cable between your computer and the
Rosemount VeriCase.
5. To start the verification procedure, the switch should be turned from
position 0 to position 1.
April 2019 Quick Start Guide
Quick Start Guide 5

3 Verify the Rosemount 3308 transmitter
Prerequisites
1. Fill in the details in the Verification Data tab of the Excel workbook.
Record the serial number of the device from the nameplate of the
transmitter.
2. (Optional) Select the Imperial Units check box to enter data in inches
and Fahrenheit.
Note
There is a possible inaccuracy of 1.25 mm (0,05 in.) when inches are
used for the display.
Procedure
1. Start Instrument Inspector Application.
2. Under HART, double-click the device icon.
Quick Start Guide April 2019
6 Rosemount VeriCase

3. Make sure the cable switch on the Rosemount VeriCase is set to
position 1.
4. Select Service Tools → Routine Maintenance, and then select
Verification.
5. In the Verification window, select Next.
6. Enter the Distance and the Electronics Temperature, displayed on the
Verification window, to the Excel workbook.
Note
Make sure you convert the distance from meters to millimeters.
April 2019 Quick Start Guide
Quick Start Guide 7

7. Enter the VeriCase temperature, displayed on the device, to the Excel
workbook.
8. Switch to the next cable on the Rosemount VeriCase, and then select
Next.
9. Repeat Step 6-Step 8 for all six cable lengths.
10. When all the cables are measured, select Finish, and then select
Next.
Quick Start Guide April 2019
8 Rosemount VeriCase

11. After the configuration is restored, disconnect communication to the
transmitter.
April 2019 Quick Start Guide
Quick Start Guide 9

4 Verify the Rosemount 5300 transmitter
Prerequisites
Open the Rosemount Radar Master and record the serial number and
firmware revision of the device to be tested in the Verification data tab of
the workbook. This information can be found in the Device Properties
window in the Device menu in Rosemount Radar Master.
Note
Inches or millimeters should be selected for measurement units (there is a
possible inaccuracy of 1.25 mm (0,05 in.) when inches are used for the
display).
Procedure
1. Configure device for verification.
a) Select Device → Backup Config to File… and save a backup
file of the current device.
The backup file needs to be reloaded once the verification is
complete.
b) Select Setup → Tank and configure the following parameters
for the transmitter that will be tested:
•Probe type: User Defined
•Probe length: Longest cable length +50 cm (20 in)
•Probe Impedance: 100 Ω
•Reference Pulse Amplitude: 3000 mV
Quick Start Guide April 2019
10 Rosemount VeriCase