Emerson Rosemount 3051S Series Configuration guide

Manual Supplement
00809-0100-4851, Rev AA
2017
Rosemount™ 3051S Series of Instrumentation
High Pressure Solutions
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 23
Operation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24
Safety Instrumented Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 25
Advanced HART Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 25
Specifications and Reference Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26
Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 52

2
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
Section 1 Introduction
1.1 Using this manual
This manual is intended to be used as a supplement to the Rosemount 3051S Reference Manuals. Since
the Rosemount 3051S High Static Differential Pressure Transmitter (Rosemount 3051SHP) and
Rosemount 3051S utilize similar components, certain sections of this manual will be linked to the
corresponding Rosemount 3051S Reference Manual section. Any information that differs from the
Rosemount 3051S product will be covered within this manual.
The sections in this manual provide information on installing, operating, and maintaining the
Rosemount 3051SHP. The sections are organized as follows:
Section 1: Introduction provides an introduction to the pressure transmitter, how to use the manual,
models covered by this manual, and other support information for the transmitter.
Section 2: Installation contains instructions for mounting the transmitter, connecting it to the
process, and wiring the transmitter.
Section 3: Configuration provides instruction on commissioning and operating Rosemount
3051SHP transmitters from a bench computer or a hand held field device. Information on software
functions, configuration parameters, and on line variables are also included.
Section 4: Operation and Maintenance contains techniques to maintain the transmitter, and
disassembly/assembly directions.
Section 5: Troubleshooting provides troubleshooting techniques for the most common operating
issues.
Section 6: Safety Instrumented Systems contains identification, commissioning, maintenance, and
operations information for the Rosemount 3051SHP SIS Safety Transmitter.
Section 7: Advanced HART Diagnostics contains procedures for installation, configuration, and
operation of the Rosemount 3051SHP HART Diagnostics option.
Section 8: Specifications and Reference Data supplies reference and specification data, as well as
ordering information.
Section 9: Product Certifications contains intrinsic safety approval information, European ATEX
directive information, and approval drawings.
1.2 Product recycling/disposal
Recycling of equipment and packaging should be taken into consideration and disposed of in accordance
with local and national legislation/regulations.

3
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
Section 2 Installation
NOTICE
This section provides basic guidelines for Rosemount 3051SHP. It does not provide instructions for
configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flameproof, or
intrinsically safe (I.S.) installations. This manual is also available electronically on
Emerson.com/Rosemount.
Shipping considerations for wireless products
The unit was shipped to you without the power module installed. Remove the power module prior
to shipping the unit.
Each power module contains two “C” size primary lithium batteries. Primary lithium batteries are
regulated in transportation by the U.S. Department of Transportation, and are also covered by IATA
(International Air Transport Association), ICAO (International Civil Aviation Organization), and ARD
(European Ground Transportation of Dangerous Goods). It is the responsibility of the shipper to
ensure compliance with these or any other local requirements. Consult current regulations and
requirements before shipping.
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Review “Product
Certifications” on page 52 for any restrictions associated with a safe installation.
Before connecting a HART®-based communicator in an explosive atmosphere, make sure the
instruments in the loop are installed in accordance with intrinsically safe or non-incendive field
wiring practices.
In an Explosion-proof/Flameproof installation, do not remove the transmitter covers when power is
applied to the unit.
Process leaks may cause harm or result in death.
To avoid process leaks, ensure secure connection with coned-and-threaded connection.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause
electrical shock.
Conduit/cable entries
Unless marked, the conduit/cable entries in the transmitter housing use a 1/2–14 NPT thread form.
Entries marked “M20” are M20 x 1.5 thread form. On devices with multiple conduit entries, all
entries will have the same thread form. Only use plugs, adapters, glands, or conduit with a
compatible thread form when closing these entries.
When installing in a hazardous location, use only appropriately listed or Ex certified flameproof/dust
plugs, adapters, or glands in cable/conduit entries.

4
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
2.1 System readiness
Note
The system readiness information is for the selectable HART 5/HART 7 Advanced Diagnostics (option code DA2)
version of the transmitter only.
2.1.1 Confirm HART Revision capability
If using HART based control or asset management systems, confirm the HART capability of those
systems prior to transmitter installation. Not all systems are capable of communicating with HART
Revision 7 Protocol. This transmitter can be configured for either HART Revision 5 or 7.
For instructions on how to change the HART revision of your transmitter, see the Rosemount 3051S
Reference Manual.
2.1.2 Confirm correct device driver
Verify the latest device driver (DD/DTM™) is loaded on your systems to ensure proper
communications.
Download the latest device driver at Emerson.com or FieldCommGroup.org.
Table 1-1 provides the information necessary to ensure you have the correct device driver and
documentation for your device.
Wireless/power module considerations
The power module may be replaced in a hazardous area. The power module has surface
resistivity greater than one gigaohm and must be properly installed in the wireless device
enclosure. Care must be taken during transportation to and from the point of installation to
prevent electrostatic charge build-up.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions. This device may not cause harmful interference. This device must accept any
interference received, including interference that may cause undesired operation. This device
must be installed to ensure a minimum antenna separation distance of 20 cm from all persons.
Table 1-1. Device Revisions and Files
Identify device Find device driver
Review
instructions Review functionality
Software
release
date
NAMUR
software
revision(1)
HART
software
revision(2)
HART
universal
revision
Device
revision(3)
Manual
document
number Changes to software
Apr-16 1.0.0 20 7 4 00809-0100-4801 HART Revision 5 and 7
selectable
5 3
Oct-10 N/A 12 5 3 00809-0100-4801 Added Power Advisory,
mA Output,
Power Consumption,
Coefficient of Variation

5
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
2.2 Mount the transmitter
2.2.1 Liquid flow applications
1. Place taps to the side of the line.
2. Mount beside or below the taps.
2.2.2 Gas flow applications
1. Place taps in the top or side of the line.
2. Mount beside or above the taps.
Note
Bracket required to support the transmitter and the 1/4-in. tubing going into the transmitter.
May-07 N/A 7 5 2 00809-0100-4801 Update Statistical Process
Monitoring Capability
Sep-06 N/A 4, 5, 6 5 1 00809-0100-4801 N/A
1. NAMUR software revision is located on the hardware tag of the device. In accordance with NE53, revisions of the least significant level X (of
1.0.X) do not change functionality or operation of the device and will not be reflected in the review functionality column.
2. HART software revision can be read using a HART capable configuration tool.
3. Device driver file names use Device and DD Revision, e.g. 10_01. HART Protocol is designed to enable legacy device driver revisions to
continue to communicate with new HART devices. To access new functionality, the new device driver must be downloaded. It is
recommended to download new device driver files to ensure full functionality.
Table 1-1. Device Revisions and Files
Identify device Find device driver
Review
instructions Review functionality

6
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
2.2.3 Using a mounting bracket
The images below provide instructions on how to properly mount the transmitter using the Emerson™
provided mounting brackets. Use only bolts provided with the transmitter or sold as Emerson spare
parts. Bolts should be tightened to a torque of 125 in-lb.
2.2.4 Environmental seal for housing
Thread sealing (PTFE) tape or paste on male threads of conduit is required to provide a water/dust tight
conduit seal and meets requirements of NEMA®Type 4X, IP66, and IP68. Consult factory if other Ingress
Protection ratings are required.
For M20 threads, install conduit plugs to full thread engagement or until mechanical resistance is met.
Note
IP 68 is not available with wireless output.
2.2.5 Installing high pressure coned and threaded connection
The transmitter comes with an autoclave connection designed for high pressure applications. Follow the
steps below to properly connect the transmitter to your process:
1. Apply a small amount of process-compatible lubricant to the gland nut threads.
2. Slip the gland nut onto the tube, then thread the collar onto the tube end (the collar is reverse
threaded).
3. Apply a small amount of process-compatible lubricant applied to the tube cone to help prevent
galling and facilitate sealing. Insert the tubing into the connection and tighten gland nut finger
tight.
Panel mount Pipe mount
Housings
PlantWeb™Junction box Remote mount display

7
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
4. Tighten the gland nut to a torque of 25 ft-lb.
Note
A weep hole has been designed into the transmitter for safety and leak detection. If fluid begins to leak from the
weep hole after torquing, isolate the process pressure, disconnect the transmitter, and reseal until the leak is
resolved.
All Rosemount 3051SHP Transmitters come with 316L SST tagging.
2.2.6 Wireless considerations (if applicable)
Power up sequence
The power module should not be installed on any wireless device until the Emerson Smart Wireless
Gateway (Gateway) has been installed and functioning properly. See “Power up transmitter” on page 11
for more details.
Antenna position
Position the antenna vertically, either straight up or straight down (see Figure 1-1 on page 7). The
antenna should be approximately 3 ft. (1 m) from any large structure or building to allow clear
communication to other devices.
Figure 1-1. Antenna Position
High gain, remote antenna mounting instructions (WN wireless
option only)
The high gain, remote antenna option provides flexibility for mounting the transmitter based on wireless
connectivity, lightning protection, and current work practices (see Figure 1-2 on page 9).

8
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
The high gain, remote mount antenna kit includes coaxial sealant for the cable connections for the
lightning arrestor and antenna.
Find a location where the remote antenna has optimal wireless performance. Ideally this will be 15–25 ft.
(4,6–7,6 m) above the ground or 6 ft. (2 m) above obstructions or major infrastructure. To install the
remote antenna use the following procedure:
1. Mount the antenna on a 1.5- to 2-in. pipe mast using the supplied mounting equipment.
2. Connect the lightning arrestor directly to the top of the transmitter.
3. Install the grounding lug, lock washer, and nut on top of lightning arrestor.
4. Connect the antenna to the lightning arrestor using the supplied LMR-400 coaxial cable ensuring the
drip loop is not closer than 1 ft. (0,3 m) from the lightning arrestor.
5. Use the coaxial sealant to seal each connection between the wireless field device, lightning arrestor,
cable, and antenna.
6. Ensure the mounting mast and lightning arrestor are grounded according to local/national electrical
code.
Any spare lengths of coaxial cable should be placed in 12-in. (0,3 m) coils.
When installing the remote mount antenna for the transmitter, always use established safety
procedures to avoid falling or contact with high-power electrical lines.
Install remote antenna components for the transmitter in compliance with local and national
electrical codes and use best practices for lightning protection.
Before installing consult with the local area electrical inspector, electrical officer, and work area
supervisor.
The remote antenna option is specifically engineered to provide installation flexibility while
optimizing wireless performance and local spectrum approvals. To maintain wireless performance
and avoid non-compliance with spectrum regulations, do not change the length of cable or the
antenna type.
If the supplied remote mount antenna kit is not installed per these instructions, Emerson is not
responsible for wireless performance or non-compliance with spectrum regulations.

9
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
Figure 1-2. Rosemount 3051SHP with High Gain, Remote Antenna
A. Lightning arrestor
B. Antenna
C. Mounting mast
D. Drip loop
Note: Weather proofing is required!
The remote mount antenna kit includes coaxial sealant for weather proofing the cable connections for the lightning
arrestor, antenna, and the transmitter. Coaxial sealant must be applied to guarantee performance of the wireless
field network. See Figure 1-3 for details on how to apply coaxial sealant.
Figure 1-3. Applying Coaxial Sealant to Cable Connections
2.3 Consider housing rotation
To improve field access to wiring or to better view the optional LCD display:
1. Loosen the housing rotation set screw.
2. First rotate the housing clockwise to the desired location. If the desired location cannot be achieved
due to thread limit, rotate the housing counter clockwise to the desired location (up to 360° from
thread limit).
3. Retighten the housing rotation set screw up to 30 in-lb.
4. For wireless, consider access to the power module when selecting housing rotation.
A
B
D
C

10
Manual Supplement
00809-0100-4851, Rev AA
Rosemount 3051S High Pressure
2017
Rosemount 3051S High Pressure
Figure 1-4. Transmitter Housing Set Screw
A. Housing rotation set screw (3/32-in.)
Note
Do not rotate the housing more than 180° without first performing a disassembly procedure. Over-rotation may
sever the electrical connection between the sensor module and the feature board electronics.
2.4 Set switches and jumpers
If alarm and security adjustment option is not installed, the transmitter will operate normally with the
default alarm condition alarm “high” and the security “off”.
1. Do not remove the transmitter covers in explosive atmospheres when the circuit is live. If the
transmitters is live, set the loop to manual and remove power.
2. Remove the electronics compartment cover. On the PlantWeb housing the cover is opposite the
field terminals side, or on the junction box housing remove the terminal block cover. Do not remove
the housing cover in explosive environments.
3. On the PlantWeb housing, slide the security and alarm switches into the preferred position by using
a small screwdriver (an LCD display or an adjustment module must be in place to activate the
switches). On the junction box housing pull the pins out and rotate 90° into desired position to set
the security and alarm.
4. Reinstall the housing cover so that metal contacts metal to meet explosion-proof requirements.
Figure 1-5. Transmitter Switch and Jumper Configuration
A. Meter/adjustment module
B. Security
C. Alarm
PlantWeb Junction box
PlantWeb Junction box
A
A
A
BC
B
C