Endon Pipe User manual

Pipe Semi Flush Fitting
Safety Warnings
INSTRUCTION MANUAL
• Thisproductisonlysuitableforconnectiontoa240V~50HzsupplyinaccordancewithcurrentIEEwiring
regulations,andshouldbeinstalledinaccordancewithlocalbuildingregulations.Itisforindooruseonly,andis
notsuitableforabathroomlocation.
• Beforeinstallingyourlightttingalwaysswitcho󰀨themainssupply,andremovetheappropriatefuseorswitch
o󰀨theappropriatecircuitbreakerbeforecommencinginstallation.Ensurethatnooneelsehasaccessthatwould
enablethesupplytobeinadvertentlyreconnected.
• This is a Class 1 product and must be Earthed. Theterminalblocksaresuppliedaccordingtorequirementsof
thetting.
• Nevertbulbsofahigherwattagethanthosespeciedonthelabel(asthesemaycauseoverheatingand
damagethetting).
• Thisproductmaycontaindelicateparts–becarefulduringhandlingandmaintenancetoavoidbreakage.
• Ifyouareinanydoubtaboutyourcompetencepleaseconsultaqualiedelectrician.
• Ifanymodicationismadeitwillinvalidatethewarrantyandmayrendertheproductunsafe.
• Thisproductisdimmablewhenusedwithasuitablebulbandswitch.
EndonLighting,LS90SE
Assembly/ User Instructions
Before you start
Pleasereadtheseinstructionscarefullybeforettingandretainforreference.Checkthepackagingandmake
surethatyouhavealltherequiredparts.Followeachassemblystepinordertopreventincorrectassembly.
Ensurethattheproductisfullyassembledasillustratedbeforeuse.
The Light pack contains:
Lighttting
Fixingpack
The following tools may be required:
Selectionofcrossandatheadscrewdrivers.
Electricdrillandassorteddrillbits.
Wirestrippers.
Theseassemblydiagramsareintendedasaguide–ifindoubtconsultaqualiedelectrician.
Care Information
Allow10minutestocoolbeforereplacing,adjustingorcleaning.
Cleanwithadryclothonly.Donotuseliquidorabrasivecleanersonthisproduct.
1. Decideonthepositionofthelighttting,orremoveexistinglighttting.Takeanoteofthepositionofthe
electricalconnections.Ensurethereisasolidmountingsurface,preferablyawoodenjoistorjoistbridgeto
supporttheweightofthelighttting.
2. Removethetwosidescrews(A)andretainthemforre-use.Usethexingbracket(B)asatemplatetomark
thescrewholes,andsecuretothewallwithappropriatexings(C),makingsurethebracketiscorrectly
aligned.
3. Supportyourttingandconnectthehousewiringtotheterminalblock-seeexpandedwiringdiagramD).
NOTE: This is a Class 1 product and MUST be earthed.
4. Securethewallcupoverthebracketbyusingthescrews(A)removedinPoint2.
5. Fitthebulbs(E-notsupplied).NOTE:Nevertbulbsofahigherwattagethanthosespeciedonthe
label(asthesemaycauseoverheatinganddamagethetting).
6. Turnonthepowerandtest.
78763-Pipe-SF20190813

EndonLighting,LS90SE
Assembly/ User Instructions
78763-Pipe-SF20190813
B
CD
A
E