Endress+Hauser Proline Cubemass C 300 User manual

Products Solutions Services
Operating Instructions
Proline Cubemass C 300
Coriolis flowmeter
HART
BA01483D/06/EN/05.22-00
71574975
2022-08-01
Valid as of version
01.06.zz (Device firmware)

Proline Cubemass C 300
2 Endress+Hauser
• Make sure the document is stored in a safe place such that it is always available when
working on or with the device.
• To avoid danger to individuals or the facility, read the "Basic safety instructions" section
carefully, as well as all other safety instructions in the document that are specific to
working procedures.
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser Sales Center will supply you with current information and updates to
these instructions.

Proline Cubemass C 300 Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 6
1.1 Document function ..................... 6
1.2 Symbols .............................. 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Communication-specific symbols ..... 6
1.2.4 Tool symbols .................... 7
1.2.5 Symbols for
certain types of information ......... 7
1.2.6 Symbols in graphics ............... 7
1.3 Documentation ........................ 8
1.3.1 Document function ............... 8
1.4 Registered trademarks ................... 8
2 Safety instructions .................. 9
2.1 Requirements for the personnel ............ 9
2.2 Intended use .......................... 9
2.3 Workplace safety ...................... 10
2.4 Operational safety ..................... 10
2.5 Product safety ........................ 10
2.6 IT security ........................... 11
2.7 Device-specific IT security ................ 11
2.7.1 Protecting access via hardware write
protection ..................... 11
2.7.2 Protecting access via a password .... 12
2.7.3 Access via Web server ............ 13
2.7.4 Access via OPC-UA .............. 13
2.7.5 Access via service interface (CDI-
RJ45) ........................ 13
3 Product description ................ 14
3.1 Product design ........................ 14
4 Incoming acceptance and product
identification ..................... 15
4.1 Incoming acceptance ................... 15
4.2 Product identification ................... 15
4.2.1 Transmitter nameplate ........... 16
4.2.2 Sensor nameplate ............... 17
4.2.3 Symbols on measuring device ...... 18
5 Storage and transport ............. 19
5.1 Storage conditions ..................... 19
5.2 Transporting the product ................ 19
5.2.1 Measuring devices without lifting
lugs ......................... 19
5.2.2 Measuring devices with lifting lugs .. 20
5.2.3 Transporting with a fork lift ........ 20
5.3 Packaging disposal ..................... 20
6 Mounting ......................... 21
6.1 Mounting requirements ................. 21
6.1.1 Mounting position ............... 21
6.1.2 Environment and process
requirements .................. 23
6.1.3 Special mounting instructions ...... 24
6.2 Mounting the measuring device ........... 27
6.2.1 Required tools .................. 27
6.2.2 Preparing the measuring device ..... 27
6.2.3 Mounting the measuring device ..... 27
6.2.4 Turning the transmitter housing .... 27
6.2.5 Turning the display module ........ 28
6.3 Post-installation check .................. 29
7 Electrical connection .............. 30
7.1 Electrical safety ....................... 30
7.2 Connecting requirements ................ 30
7.2.1 Required tools .................. 30
7.2.2 Requirements for connecting cable ... 30
7.2.3 Terminal assignment ............. 33
7.2.4 Preparing the measuring device ..... 33
7.3 Connecting the measuring device .......... 33
7.3.1 Connecting the transmitter ........ 33
7.3.2 Connecting the remote display and
operating module DKX001 ........ 36
7.4 Potential equalization .................. 36
7.4.1 Requirements .................. 36
7.5 Special connection instructions ............ 37
7.5.1 Connection examples ............. 37
7.6 Ensuring the degree of protection .......... 41
7.7 Post-connection check .................. 41
8 Operation options ................. 43
8.1 Overview of operation options ............ 43
8.2 Structure and function of the operating
menu .............................. 44
8.2.1 Structure of the operating menu .... 44
8.2.2 Operating philosophy ............ 45
8.3 Access to the operating menu via the local
display ............................. 46
8.3.1 Operational display .............. 46
8.3.2 Navigation view ................ 47
8.3.3 Editing view ................... 49
8.3.4 Operating elements .............. 51
8.3.5 Opening the context menu ......... 52
8.3.6 Navigating and selecting from list ... 53
8.3.7 Calling the parameter directly ...... 53
8.3.8 Calling up help text .............. 54
8.3.9 Changing the parameters ......... 54
8.3.10 User roles and related access
authorization .................. 55
8.3.11 Disabling write protection via access
code ......................... 55

Table of contents Proline Cubemass C 300
4 Endress+Hauser
8.3.12 Enabling and disabling the keypad
lock ......................... 56
8.4 Access to the operating menu via the Web
browser ............................. 56
8.4.1 Function scope ................. 56
8.4.2 Requirements .................. 57
8.4.3 Establishing a connection ......... 58
8.4.4 Logging on .................... 60
8.4.5 User interface .................. 61
8.4.6 Disabling the Web server .......... 62
8.4.7 Logging out .................... 62
8.5 Access to the operating menu via the
operating tool ........................ 63
8.5.1 Connecting the operating tool ...... 63
8.5.2 Field Xpert SFX350, SFX370 ....... 66
8.5.3 FieldCare ..................... 66
8.5.4 DeviceCare .................... 68
8.5.5 AMS Device Manager ............ 68
8.5.6 SIMATIC PDM .................. 69
8.5.7 Field Communicator 475 .......... 69
9 System integration ................ 70
9.1 Overview of device description files ......... 70
9.1.1 Current version data for the device ... 70
9.1.2 Operating tools ................. 70
9.2 Measured variables via HART protocol ...... 71
9.2.1 Device variables ................. 73
9.3 Other settings ........................ 74
10 Commissioning .................... 77
10.1 Function check ....................... 77
10.2 Switching on the measuring device ......... 77
10.3 Setting the operating language ............ 77
10.4 Configuring the measuring device .......... 77
10.4.1 Defining the tag name ............ 79
10.4.2 Setting the system units .......... 79
10.4.3 Selecting and setting the medium ... 82
10.4.4 Displaying the I/O configuration .... 84
10.4.5 Configuring the current input ...... 85
10.4.6 Configuring the status input ....... 86
10.4.7 Configuring the current output ..... 87
10.4.8 Configuring the pulse/frequency/
switch output .................. 91
10.4.9 Configuring the relay output ....... 98
10.4.10 Configuring the double pulse output 100
10.4.11 Configuring the local display ...... 102
10.4.12 Configuring the low flow cut off .... 106
10.4.13 Configuring partially filled pipe
detection .................... 107
10.5 Advanced settings .................... 108
10.5.1 Using the parameter to enter the
access code ................... 109
10.5.2 Calculated process variables ....... 109
10.5.3 Carrying out a sensor adjustment ... 110
10.5.4 Configuring the totalizer ......... 114
10.5.5 Carrying out additional display
configurations ................. 116
10.5.6 WLAN configuration ............ 122
10.5.7 Configuration management ....... 124
10.5.8 Using parameters for device
administration ................ 125
10.6 Simulation .......................... 127
10.7 Protecting settings from unauthorized access 129
10.7.1 Write protection via access code ... 129
10.7.2 Write protection via write protection
switch ....................... 131
11 Operation ....................... 133
11.1 Reading off the device locking status ...... 133
11.2 Adjusting the operating language ......... 133
11.3 Configuring the display ................ 133
11.4 Reading measured values ............... 133
11.4.1 "Measured variables" submenu ..... 134
11.4.2 "Totalizer" submenu ............. 136
11.4.3 "Input values" submenu .......... 137
11.4.4 Output values ................. 138
11.5 Adapting the measuring device to the process
conditions .......................... 140
11.6 Performing a totalizer reset ............. 140
11.6.1 Function scope of "Control Totalizer"
parameter .................... 141
11.6.2 Function scope of the "Reset all
totalizers" parameter ............ 141
11.7 Show data logging .................... 142
11.8 Gas Fraction Handler .................. 145
11.8.1 "Measurement mode" submenu .... 146
11.8.2 "Medium index" submenu ......... 146
12 Diagnostics and troubleshooting .. 148
12.1 General troubleshooting ................ 148
12.2 Diagnostic information via light emitting
diodes ............................. 150
12.2.1 Transmitter ................... 150
12.3 Diagnostic information on local display ..... 152
12.3.1 Diagnostic message ............. 152
12.3.2 Calling up remedial measures ..... 154
12.4 Diagnostic information in the Web browser .154
12.4.1 Diagnostic options .............. 154
12.4.2 Calling up remedy information .... 155
12.5 Diagnostic information in FieldCare or
DeviceCare ......................... 156
12.5.1 Diagnostic options .............. 156
12.5.2 Calling up remedy information .... 157
12.6 Adapting the diagnostic information ...... 157
12.6.1 Adapting the diagnostic behavior ... 157
12.6.2 Adapting the status signal ........ 157
12.7 Overview of diagnostic information ....... 158
12.8 Pending diagnostic events .............. 163
12.9 Diagnostic list ....................... 164
12.10 Event logbook ....................... 164
12.10.1 Reading out the event logbook ..... 164
12.10.2 Filtering the event logbook ....... 165
12.10.3 Overview of information events .... 165
12.11 Resetting the measuring device .......... 167
12.11.1 Function scope of "Device reset"
parameter .................... 167

Proline Cubemass C 300 Table of contents
Endress+Hauser 5
12.12 Device information ................... 167
12.13 Firmware history ..................... 169
12.14 Device history and compatibility .......... 170
13 Maintenance .................... 171
13.1 Maintenance tasks .................... 171
13.1.1 Exterior cleaning ............... 171
13.1.2 Interior cleaning ............... 171
13.2 Measuring and test equipment ........... 171
13.3 Endress+Hauser services ............... 171
14 Repair ........................... 172
14.1 General information .................. 172
14.1.1 Repair and conversion concept ..... 172
14.1.2 Notes for repair and conversion .... 172
14.2 Spare parts ......................... 172
14.3 Endress+Hauser services ............... 172
14.4 Return ............................. 172
14.5 Disposal ........................... 173
14.5.1 Removing the measuring device .... 173
14.5.2 Disposing of the measuring device .. 173
15 Accessories ...................... 174
15.1 Device-specific accessories .............. 174
15.1.1 For the transmitter ............. 174
15.2 Communication-specific accessories ....... 175
15.3 Service-specific accessories .............. 176
15.4 System components ................... 176
16 Technical data ................... 177
16.1 Application ......................... 177
16.2 Function and system design ............. 177
16.3 Input .............................. 178
16.4 Output ............................ 181
16.5 Power supply ........................ 187
16.6 Performance characteristics ............. 189
16.7 Installation ......................... 192
16.8 Environment ........................ 193
16.9 Process ............................ 194
16.10 Mechanical construction ............... 195
16.11 Operability ......................... 198
16.12 Certificates and approvals .............. 202
16.13 Application packages .................. 204
16.14 Accessories ......................... 206
16.15 Supplementary documentation ........... 206
Index ................................. 209

About this document Proline Cubemass C 300
6 Endress+Hauser
1 About this document
1.1 Document function
These Operating Instructions contain all the information required in the various life cycle
phases of the device: from product identification, incoming acceptance and storage, to
installation, connection, operation and commissioning, through to troubleshooting,
maintenance and disposal.
1.2 Symbols
1.2.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning
Direct current
Alternating current
Direct current and alternating current
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a
grounding system.
Potential equalization connection (PE: protective earth)
Ground terminals that must be connected to ground prior to establishing any other
connections.
The ground terminals are located on the interior and exterior of the device:
• Interior ground terminal: potential equalization is connected to the supply network.
• Exterior ground terminal: device is connected to the plant grounding system.
1.2.3 Communication-specific symbols
Symbol Meaning
Wireless Local Area Network (WLAN)
Communication via a wireless, local network.
LED
Light emitting diode is off.

Proline Cubemass C 300 About this document
Endress+Hauser 7
Symbol Meaning
LED
Light emitting diode is on.
LED
Light emitting diode is flashing.
1.2.4 Tool symbols
Symbol Meaning
Flat-blade screwdriver
Allen key
Open-ended wrench
1.2.5 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation
A
Reference to page
Reference to graphic
Notice or individual step to be observed
1.
,
2.
,
3.
… Series of steps
Result of a step
Help in the event of a problem
Visual inspection
1.2.6 Symbols in graphics
Symbol Meaning
1, 2, 3, ... Item numbers
1.
,
2.
,
3.
, … Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
-
Hazardous area

About this document Proline Cubemass C 300
8 Endress+Hauser
Symbol Meaning
.
Safe area (non-hazardous area)
Flow direction
1.3 Documentation
For an overview of the scope of the associated Technical Documentation, refer to the
following:
•W@M Device Viewer (www.endress.com/deviceviewer): Enter the serial number
from the nameplate
•Endress+Hauser Operations App: Enter the serial number from the nameplate or
scan the matrix code on the nameplate
1.3.1 Document function
Document type Purpose and content of the document
Technical Information (TI) Planning aid for your device
The document contains all the technical data on the device and provides
an overview of the accessories and other products that can be ordered for
the device.
Brief Operating Instructions (KA) Guide that takes you quickly to the 1st measured value
The Brief Operating Instructions contain all the essential information
from incoming acceptance to initial commissioning.
Operating Instructions (BA) Your reference guide
These Operating Instructions contain all the information that is required
in the various life cycle phases of the device: from product identification,
incoming acceptance and storage, to mounting, connection, operation
and commissioning, through to troubleshooting, maintenance and
disposal.
Description of Device Parameters
(GP)
Reference for your parameters
The document provides a detailed explanation of each individual
parameter. The description is aimed at those who work with the device
over the entire life cycle and perform specific configurations.
Safety Instructions (XA) Depending on the approval, safety instructions for electrical equipment in
hazardous areas are also supplied with the device. They are an integral
part of the Operating Instructions.
The nameplate indicates which Safety Instructions (XA) apply to
the device in question.
Supplementary device-dependent
documentation
Additional documents are supplied depending on the device version
ordered: Always comply strictly with the instructions in the
supplementary documentation. The supplementary documentation is an
integral part of the device documentation.
1.4 Registered trademarks
HART®
Registered trademark of the FieldComm Group, Austin, Texas, USA
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA

Proline Cubemass C 300 Safety instructions
Endress+Hauser 9
2 Safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill
the following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Are authorized by the plant owner/operator.
‣Are familiar with federal/national regulations.
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the
application).
‣Follow instructions and comply with basic conditions.
The operating personnel must fulfill the following requirements:
‣Are instructed and authorized according to the requirements of the task by the facility's
owner-operator.
‣Follow the instructions in this manual.
2.2 Intended use
Application and media
The measuring device described in this manual is intended only for the flow measurement
of liquids and gases.
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or in applications
where there is an increased risk due to process pressure, are marked accordingly on the
nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Keep within the specified pressure and temperature range.
‣Only use the measuring device in full compliance with the data on the nameplate and
the general conditions listed in the Operating Instructions and supplementary
documentation.
‣Based on the nameplate, check whether the ordered device is permitted for the
intended use in the hazardous area (e.g. explosion protection, pressure vessel safety).
‣Use the measuring device only for media to which the process-wetted materials are
sufficiently resistant.
‣If the ambient temperature of the measuring device is outside the atmospheric
temperature, it is absolutely essential to comply with the relevant basic conditions as
specified in the device documentation→  8.
‣Protect the measuring device permanently against corrosion from environmental
influences.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage
caused by improper or non-designated use.
LWARNING
Danger of breakage due to corrosive or abrasive fluids and ambient conditions!
‣Verify the compatibility of the process fluid with the sensor material.
‣Ensure the resistance of all fluid-wetted materials in the process.
‣Keep within the specified pressure and temperature range.

Safety instructions Proline Cubemass C 300
10 Endress+Hauser
NOTICE
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance
in verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
Residual risks
LWARNING
If the temperature of the media or electronics unit is high or low, this may cause the
surfaces of the device to become hot or cold. This poses a risk of burns or frostbite!
‣In the case of hot or cold medium temperatures, install appropriate protection against
contact.
LWARNING
Danger of housing breaking due to measuring tube breakage!
If a measuring tube ruptures, the pressure inside the sensor housing will rise according to
the operating process pressure.
‣Use a rupture disk.
LWARNING
Danger from medium escaping!
For device versions with a rupture disk: medium escaping under pressure can cause injury
or material damage.
‣Take precautions to prevent injury and material damage if the rupture disk is actuated.
2.3 Workplace safety
When working on and with the device:
‣Wear the required personal protective equipment as per national regulations.
2.4 Operational safety
Risk of injury!
‣Operate the device only if it is in proper technical condition, free from errors and faults.
‣The operator is responsible for the interference-free operation of the device.
Modifications to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers!
‣If modifications are nevertheless required, consult with the manufacturer.
Repair
To ensure continued operational safety and reliability:
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to the repair of an electrical device.
‣Use only original spare parts and accessories.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet
state-of-the-art safety requirements, has been tested, and left the factory in a condition in
which it is safe to operate.

Proline Cubemass C 300 Safety instructions
Endress+Hauser 11
It meets general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.
Furthermore, the device meets the legal requirements of the applicable UK regulations
(Statutory Instruments). These are listed in the UKCA Declaration of Conformity along
with the designated standards.
By selecting the order option for UKCA marking, Endress+Hauser confirms a successful
evaluation and testing of the device by affixing the UKCA mark.
Contact address Endress+Hauser UK:
Endress+Hauser Ltd.
Floats Road
Manchester M23 9NF
United Kingdom
www.uk.endress.com
2.6 IT security
Our warranty is valid only if the product is installed and used as described in the Operating
Instructions. The product is equipped with security mechanisms to protect it against any
inadvertent changes to the settings.
IT security measures, which provide additional protection for the product and associated
data transfer, must be implemented by the operators themselves in line with their security
standards.
2.7 Device-specific IT security
The device offers a range of specific functions to support protective measures on the
operator's side. These functions can be configured by the user and guarantee greater in-
operation safety if used correctly. An overview of the most important functions is provided
in the following section:
Function/interface Factory setting Recommendation
Write protection via hardware write
protection switch →  11
Not enabled On an individual basis following risk assessment
Access code
(also applies for Web server login or
FieldCare connection) →  12
Not enabled
(0000)
Assign a customized access code during
commissioning
WLAN
(order option in display module)
Enabled On an individual basis following risk assessment
WLAN security mode Enabled (WPA2-
PSK)
Do not change
WLAN passphrase
(password) →  12
Serial number Assign a customized WLAN passphrase during
commissioning
WLAN mode Access point On an individual basis following risk assessment
Web server →  13 Enabled On an individual basis following risk assessment
CDI-RJ45 service interface →  13 – On an individual basis following risk assessment
2.7.1 Protecting access via hardware write protection
Write access to the parameters of the device via the local display, Web browser or
operating tool (e.g. FieldCare, DeviceCare) can be disabled via a write protection switch

Safety instructions Proline Cubemass C 300
12 Endress+Hauser
(DIP switch on the main electronics module). When hardware write protection is enabled,
only read access to the parameters is possible.
Hardware write protection is disabled when the device is delivered →  131.
2.7.2 Protecting access via a password
Different passwords are available to protect write access to the device parameters or access
to the device via the WLAN interface.
• User-specific access code
Protect write access to the device parameters via the local display, Web browser or
operating tool (e.g. FieldCare, DeviceCare). Access authorization is clearly regulated
through the use of a user-specific access code.
• WLAN passphrase
The network key protects a connection between an operating unit (e.g. notebook or
tablet) and the device via the WLAN interface which can be ordered as an option.
• Infrastructure mode
When the device is operated in infrastructure mode, the WLAN passphrase corresponds
to the WLAN passphrase configured on the operator side.
User-specific access code
Write access to the device parameters via the local display, Web browser or operating tool
(e.g. FieldCare, DeviceCare) can be protected by the modifiable, user-specific access code
(→  129).
When the device is delivered, the device does not have an access code and is equivalent to
0000 (open).
WLAN passphrase: Operation as WLAN access point
A connection between an operating unit (e.g. notebook or tablet) and the device via the
WLAN interface (→  65), which can be ordered as an optional extra, is protected by
the network key. The WLAN authentication of the network key complies with the
IEEE 802.11 standard.
When the device is delivered, the network key is pre-defined depending on the device. It
can be changed via the WLAN settings submenu in the WLAN passphrase parameter
(→  123).
Infrastructure mode
A connection between the device and WLAN access point is protected by means of an SSID
and passphrase on the system side. Please contact the relevant system administrator for
access.
General notes on the use of passwords
• The access code and network key supplied with the device should be changed during
commissioning.
• Follow the general rules for generating a secure password when defining and managing
the access code or network key.
• The user is responsible for the management and careful handling of the access code and
network key.
• For information on configuring the access code or on what to do if you lose the
password, for example, see the "Write protection via access code" section →  129

Proline Cubemass C 300 Safety instructions
Endress+Hauser 13
2.7.3 Access via Web server
The device can be operated and configured via a Web browser with the integrated Web
server (→  56). The connection is via the service interface (CDI-RJ45) or the WLAN
interface.
The Web server is enabled when the device is delivered. The Web server can be disabled if
necessary (e.g. after commissioning) via the Web server functionality parameter.
The device and status information can be hidden on the login page. This prevents
unauthorized access to the information.
For detailed information on device parameters, see:
The "Description of Device Parameters" document .
2.7.4 Access via OPC-UA
The device can communicate with OPC UA clients using the "OPC UA Server" application
package.
The OPC UA server integrated in the device can be accessed via the WLAN access point
using the WLAN interface - which can be ordered as an optional extra - or the service
interface (CDI- RJ45) via Ethernet network. Access rights and authorization as per
separate configuration.
The following Security Modes are supported as per the OPC UA Specification (IEC 62541):
• None
• Basic128Rsa15 – signed
• Basic128Rsa15 – signed and encrypted
2.7.5 Access via service interface (CDI-RJ45)
The device can be connected to a network via the service interface (CDI-RJ45). Device-
specific functions guarantee the secure operation of the device in a network.
The use of relevant industrial standards and guidelines that have been defined by national
and international safety committees, such as IEC/ISA62443 or the IEEE, is recommended.
This includes organizational security measures such as the assignment of access
authorization as well as technical measures such as network segmentation.
Transmitters with an Ex de approval may not be connected via the service interface
(CDI-RJ45)!
Order code for "Approval transmitter + sensor", options (Ex de): BA, BB, C1, C2, GA,
GB, MA, MB, NA, NB

Product description Proline Cubemass C 300
14 Endress+Hauser
3 Product description
The device consists of a transmitter and a sensor.
The device is available as a compact version:
The transmitter and sensor form a mechanical unit.
3.1 Product design
5
4
Nicht unter
Spannung öffnen
Do not open when
energized
Ne pas ouvrir
sous tension
Power
I/O
N
i
c
ht
u
n
t
e
r
a
r
e
ö
f
f
n
e
n
D
i
s
p
l
a
y
+E
ESC
–
123
A0029586
 1 Important components of a measuring device
1 Connection compartment cover
2 Display module
3 Transmitter housing
4 Electronics compartment cover
5 Sensor

Proline Cubemass C 300 Incoming acceptance and product identification
Endress+Hauser 15
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
1
2
1
2
Are the order codes on the
delivery note (1) and the
product sticker (2) identical?
Are the goods undamaged?
Order code:
Ser. no.:
Ext. ord. cd.:
ii
Date:
Do the data on the
nameplate match the
ordering information on the
delivery note?
Is the envelope present with
accompanying documents?
• If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.
• The Technical Documentation is available via the Internet or via the Endress+Hauser
Operations App, see the "Product identification" section →  16.
4.2 Product identification
The following options are available for identification of the device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
• Enter the serial numbers from the nameplates in the Device Viewer
(www.endress.com/deviceviewer): all the information about the device is displayed.
• Enter the serial numbers from the nameplates into the Endress+Hauser Operations App
or scan the DataMatrix code on the nameplate with the Endress+Hauser Operations App:
all the information about the device is displayed.

Incoming acceptance and product identification Proline Cubemass C 300
16 Endress+Hauser
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The chapters "Additional standard documentation on the device" and "Supplementary
device-dependent documentation"
• The Device Viewer: Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate or
scan the DataMatrix code on the nameplate.
4.2.1 Transmitter nameplate
Order code:
Ser. no.:
Ext. ord. cd.:
ii
Date:
1 2 3 4 5
20
19
6
7
8
9
13 12 1011
18
17
16
14
15
A0029192
 2 Example of a transmitter nameplate
1 Place of manufacture
2 Name of the transmitter
3 Order code
4 Serial number (Ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Degree of protection
7 Space for approvals: use in hazardous areas
8 Electrical connection data: available inputs and outputs
9 2-D matrix code
10 Date of manufacture: year-month
11 Document number of safety-related supplementary documentation
12 Space for approvals and certificates: e.g. CE mark, RCM tick
13 Space for degree of protection of connection and electronics compartment when used in hazardous areas
14 Firmware version (FW) and device revision (Dev.Rev.) from the factory
15 Space for additional information in the case of special products
16 Permitted temperature range for cable
17 Permitted ambient temperature (Ta)
18 Information on cable gland
19 Available inputs and outputs, supply voltage
20 Electrical connection data: supply voltage

Proline Cubemass C 300 Incoming acceptance and product identification
Endress+Hauser 17
4.2.2 Sensor nameplate
Date:
Size:
Material:
Tm:
Patents
i
Ptest =
i
Order code:
Ext. ord. cd.:
Ser. no.:
322541-0000
0044
11
1
2
3 4 5 6 7
12
8
9
13 14 15
16
17
19
18
10
A0013907
 3 Example of a sensor nameplate
1 Place of manufacture
2 Name of the sensor
3 Order code
4 Serial number (Ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Nominal diameter of the sensor
7 Test pressure of the sensor
8 Flange nominal diameter/nominal pressure
9 Material of measuring tube and manifold
10 Medium temperature range
11 CE mark, RCM-Tick mark
12 Additional information on version: certificates, approvals
13 Manufacturing date: year-month
14 Flow direction
15 2-D matrix code
16 Degree of protection
17 Approval information for explosion protection and Pressure Equipment Directive
18 Permitted ambient temperature (Ta)
19 Document number of safety-related supplementary documentation
Order code
The measuring device is reordered using the order code.
Extended order code
• The device type (product root) and basic specifications (mandatory features) are
always listed.
• Of the optional specifications (optional features), only the safety and approval-
related specifications are listed (e.g. LA). If other optional specifications are also
ordered, these are indicated collectively using the # placeholder symbol (e.g. #LA#).
• If the ordered optional specifications do not include any safety and approval-related
specifications, they are indicated by the + placeholder symbol (e.g. XXXXXX-ABCDE
+).

Incoming acceptance and product identification Proline Cubemass C 300
18 Endress+Hauser
4.2.3 Symbols on measuring device
Symbol Meaning
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious
or fatal injury. To determine the nature of the potential hazard and the measures required to
avoid it, consult the documentation accompanying the measuring device.
Reference to documentation
Refers to the corresponding device documentation.
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.

Proline Cubemass C 300 Storage and transport
Endress+Hauser 19
5 Storage and transport
5.1 Storage conditions
Observe the following notes for storage:
‣Store in the original packaging to ensure protection from shock.
‣Do not remove protective covers or protective caps installed on process connections.
They prevent mechanical damage to the sealing surfaces and contamination in the
measuring pipe.
‣Protect from direct sunlight to avoid unacceptably high surface temperatures.
‣Store in a dry and dust-free place.
‣Do not store outdoors.
Storage temperature →  193
5.2 Transporting the product
Transport the measuring device to the measuring point in the original packaging.
A0029252
Do not remove protective covers or caps installed on process connections. They
prevent mechanical damage to the sealing surfaces and contamination in the
measuring tube.
5.2.1 Measuring devices without lifting lugs
LWARNING
Center of gravity of the measuring device is higher than the suspension points of the
webbing slings.
Risk of injury if the measuring device slips.
‣Secure the measuring device against slipping or turning.
‣Observe the weight specified on the packaging (stick-on label).
A0029214

Storage and transport Proline Cubemass C 300
20 Endress+Hauser
5.2.2 Measuring devices with lifting lugs
LCAUTION
Special transportation instructions for devices with lifting lugs
‣Only use the lifting lugs fitted on the device or flanges to transport the device.
‣The device must always be secured at two lifting lugs at least.
5.2.3 Transporting with a fork lift
If transporting in wood crates, the floor structure enables the crates to be lifted lengthwise
or at both sides using a forklift.
5.3 Packaging disposal
All packaging materials are environmentally friendly and 100 % recyclable:
• Outer packaging of device
Polymer stretch wrap, complying with EU Directive 2002/95/EC (RoHS)
• Packaging
• Wooden crate treated in accordance with ISPM 15 standard, confirmed by IPPC logo
• Cardboard box in accordance with European packaging guideline 94/62EC,
recyclability confirmed by Resy symbol
• Carrying and securing materials
• Disposable plastic pallet
• Plastic straps
• Plastic adhesive strips
• Filler material
Paper pads