Enel X Way Next Gen JuiceBox User manual

Next Gen JuiceBox
User Manual
ENGLISH

2
Table of contents
Welcome to JuiceBox 3
Package Contents 3
Required Tools 3
Installation 4
Installation Prerequisites 4
Installation 4
Load Balancing 7
Locking Your JuiceBox 7
Wi-Fi Setup 8
Wi-Fi Setup - Mobile Device 8
Wi-Fi Setup - Personal Computer 15
Pairing Alexa 18
Specications 18
Characteristics 18
Connectivity 19
Dimensions 19
LED Indicator 21
Impoant Safety Information 22

3
Welcome to JuiceBox
Package Contents
>JuiceBox
>Wall bracket
>2 wall bracket screws (#10 self-tapping Phillips head wood screws)
>2 screws to hang JuiceBox onto wall bracket (#10-32 Phillips head machine screws).
Required Tools
>Phillips Screwdriver (No. 2 drive size)
>Stud sensor
>Stripper
>Wire nut or wire coupler
>Allen key
>Electrical tape
>Wrench or torque wrench
NOTE: In some markets, JuiceBox arrives secured to a cable holder that includes
keys.

4
Installation
Installation Prerequisites
JuiceBox requires either a hardwired electrical connection or a NEMA 14-50 outlet.
The JuiceBox power supply must be connected to a circuit breaker that is rated for at least
125% of the device’s continuous load.
When selecting a location to install the hardwire connection or outlet, keep in mind that
JuiceBox should be positioned:
>Within reach of the vehicle’s charge po
>18 inches above the oor or ground
>If applicable, within range of a cellular connection or the local Wi-Fi network
Installation
Fully read and understand the directions before installation. Refer to additional safety
information at the end of this document.
1. Turn o the circuit breaker to the NEMA 14-50 outlet, NEMA 6-50 outlet, or hardwired
electrical connection.
2. Use a stud sensor to determine an appropriate mounting location, then use the 2 screws
to secure the wall bracket.
NOTE: Ensure that all power connection wiring conforms to the rules and
regulations of any national and local codes.
WARNING: Do not continue this installation until the circuit breaker is turned
o.

5
Version with cable holder Version without cable
holder
Version with cable holder Version without cable holder
3. Inse the enclosure screws into the enclosure, as shown. Tighten the screws until
approximately 2 mm of thread are visible.

6
Version with cable holder Version without cable holder
4. Hang the JuiceBox onto the wall bracket.
5. Connect the JuiceBox:
>Plug-In Version: Plug the JuiceBox into the NEMA 14-50 outlet or NEMA 6-50 outlet.
>1-Phase Hardwired Version: Connect the harness to the junction box.
NOTE: If the JuiceBox does not hang securely, adjust the screws that were
installed in step 3. The 48 and 80 amp are hardwire only and do not have a plug
as shown.
WARNING: It is the installers responsibility to ensure that the JuiceBox is wired
in accordance with the local electrical code.
NOTE: For the installation wiring, please have your electrician size the conductors
for both rated wire temperature and 125% continuous load. Please refer to both
the National Electrical Code (NEC) and your local Authority Having Jurisdiction
(AHJ) for any additional requirements. 1
1The neutral wire is not used, but may need to be present in the receptacle.

7
COLOR SIGNAL
Black L1
Red L2
Green Ground
6. Turn on the circuit breaker that supplies power to the NEMA 14-50 outlet, NEMA 6-50
outlet, or hardwired electrical connection.
Load Balancing
>Only balance to the circuit level.
>Only balance stations with the same specications.
>Balancing specications cannot exceed the rated continuous load of the circuit. (50
amp circuit = 40 amp continuous load allowed) (NEC 625.41 & 42) 2017 code.
>Per NEC 625.42 additional outlets per circuit can be added due to the JuiceNet
Automated Load Management System.
Locking Your JuiceBox
After installing your JuiceBox, use the included keys to lock the JuiceBox to the wall frame.
NOTE: The hardwire versions of the JuiceBox are shipped with appropriate wires
that meet the National Electric Code (NEC) NFPA 70 and require a nearby junction
box connection. Any alteration of the supplied wiring will invalidate the warranty
and may not conform to NEC.

8
Wi-Fi Setup
Wi-Fi Setup - Mobile Device
For best results, peorm this procedure while standing within 5 ft (1.6m) of the JuiceBox.
1. Download and install the “EV JuiceNet” app onto your mobile device.
2. Log into the EV JuiceNet app. If you do not have an account, create one.
3. Select Sta.
Video walkthrough of this section

9
4. Select Connect Now.

10
5. Have the Wi-Fi network password ready, then disconnect power from the JuiceBox. In
the app, select Next.
6. Connect power to the JuiceBox. In the app, select Next.

11
7. Navigate to the Wi-Fi seings on your mobile device. Connect to the “JuiceBox-###” or
“JuiceNet-###” Wi-Fi network. If the network requires a password, use the password
“GoElectric” (case-sensitive).
NOTE: After powering the JuiceBox, steps 7 through 10 must be completed within
2 minutes.
NOTE: The actual name of the network varies by device, such as “JuiceBox-123”.

12
8. Return to the EV JuiceNet app.
9. In the EV JuiceNet app, select the preferred local Wi-Fi network.
10. Enter the Wi-Fi network password, if necessary, then select Done / Connect JuiceNet
device to Wi-Fi.

13
The app connects the JuiceBox to the Wi-Fi network.
NOTE: If prompted, verify the password, then select Done / Password is correct.

14
11. After the app conrms that Wi-Fi setup is complete, select Next to continue to the app
home screen.
NOTE: After connecting, JuiceBox checks its rmware version and peorms any
necessary updates. Wait 10 minutes before plugging in a vehicle.
NOTE: Customize your experience by following the onscreen app instructions to
select your vehicle and charging prole, or navigate to the JuiceNet dashboard on
a personal computer at hps://home.juice.net

15
Wi-Fi Setup - Personal Computer
CONNECT TO WI-FI
1. Unplug the JuiceBox, then plug it back in.
2. Open the Wi-Fi seings on your personal computer. Connect to the "JuiceBox-###" or
"JuiceNet-###" Wi-Fi network using the password "GoElectric" (case-sensitive).
3. In a web browser, navigate to 10.10.10.1 or to setup.com to view a list of available Wi-Fi
networks.
4. Select the desired Wi-Fi network. Enter the Wi-Fi network password, if necessary. Click
Connect.
Verify that the JuiceBox is connected by checking that the “Network” indicator on the
enclosure is solid blue.
NOTE: The following steps must be completed within 2 minutes of plugging in the
JuiceBox.
NOTE: The actual name of the network varies by device, such as “JuiceBox-123”.

16
SET UP JUICENET DASHBOARD
1. Log into the dashboard.
2. Select Add JuiceNet Device.
3. Enter the JuiceNet ID and select Add JuiceNet Device.
NOTE: After connecting, JuiceBox checks its rmware version and peorms any
necessary updates. Wait 10 minutes before plugging in a vehicle.
NOTE: JuiceNet detects and displays all devices on the local network. Click on the
appropriate Device ID to automatically paste it into the entry eld.

17
4. In the lefthand navigation menu, select My JuiceNet > My JuiceNet Devices.
5. Locate the appropriate device and select MORE DETAILS.
6. Select Seings.
7. Enter the device name, address, and timezone, then select Update.

18
Pairing Alexa
Refer to Pairing Alexa for more details.
Specications
Characteristics
OUTPUT POWER
32A max: Up to 7.7 kW, 32A, 1-phase
40A max: Up to 9.6 kW, 40A, 1-phase
48A max: Up to 11.5 kW, 48A, 1-phase
80A max: Up to 19.2 kW, 80A, 1-phase
INPUT VOLTAGE 208 or 240 VAC
CHARGING MODE Mode 3
LEDs Dynamic LEDs displaying charging status
PROTECTION
IP67
AC 20mA Ground Fault Detection
TEMPERATURE
RANGE From -40°C to +60°C
STANDARDS AND
CERTIFICATIONS
IEC 61851-1
UL Ceied

19
WI-FI IEE 802.11b/g/n 2.4 GHz
(OPTIONAL)
CELLULAR LTE (CAT-1)Bands B2, B4, B5, B12/B13
3G Bands B2 (1900), B5 (850); PTCRB and GCF ceication
Connectivity
Dimensions

20