ENFORCER CS-PD115-PAQ User manual

™
Infrared Proximity Sensors
Manual
•
No-touch operation reduces the risk of
spread of germs, viruses, etc., through
cross-contamination
•Triggers a warning or locking device when
the sensor is triggered
•orm C relay output (1A@30VDC)
•Adjustable output time (0.5~30 s) or toggle
•Adjustable sensor range up to 6" (15cm)
•
Selectable LED colors (turns from red to
green or green to red on activation)
•12~24 VDC Operation
•Variety of sizes allow for a wide range of
applications
•ilters out interference from other infrared
sources
•Weatherproof front panel (IP65)*
*When properly installed, see pg. 2
CS-PD115-PAQ shown
Model
Size
Material
CS
-
PD115
-
PAQ
ø
3
/
4
" (ø19mm)
Polycarbonate
CS
-
PD419
-
PQ
ø
3
/
4
" (ø19mm)
Stainless steel and polycarbonate
CS
-
PD422
-
PQ
ø
7
/
8
" (ø22mm)
Stainless steel and polycarbonate
CS
-
PD438
-
PQ
ø
1
1
/
2
" (ø38mm)
Stainless steel and polycarbonate

ENFORCER Infrared Proximity Sensors
2SECO-LARM U.S.A., Inc.
Introduction:
EN ORCER IR Proximity Sensor
s
are
compact
and
can be programmed to
unlock an electronic
door lock when an object (such as a hand) is passed in front of the sensor or trigger an
alarm when
an object (such as a valuable possession) is removed from the sensing area. This flexibility makes
the sensors ideal for both anti-theft and access control applications.
•Access control: Mount the sensor to a wall or plate in a protected area. A user can wave a hand
in front of the sensor to unlock an electric lock for no-touch, protected egress.
•Anti-theft: Place the sensor under or behind a painting or other valuable object. If the object is
removed, the sensor will trigger an alarm to alert the owner.
Specifications:
Installation
:
Model
CS
-
PD
438
-
P
Q
CS
-
PD
422
-
P
Q
CS
-
PD
419
-
P
Q
CS
-
PD
11
-
PA
Q
Diameter
ø
1
1
/
2
" (ø38mm)
ø
7
/
8
" (ø22
mm)
ø
3
/
4
" (ø19
mm)
Case material
Stainless steel and polycarbonate
Polycarbonate
Operating voltage
12~24 VDC
Power
consumption
12VDC
35mA@12VDC
30mA@12VDC
24VDC
45mA@24VDC
35mA@24VDC
30mA@12VDC
Relay type
orm C dry contact, NO/NC/COM, 1A@24VDC, 0.5A@12VAC
Connectors
Wire terminals
Response time
10ms
Output time
0.5~3
0 s
or Toggle
Sensing range
1
9
/
16
"
~6
" (4
~1
5
cm)
LED Status indicator
Selectable red/green or green/red
Operating
life
Relay
1,000,000 cycles
Sensor
100,000 Hours
IP Rating
IP65 (front panel only)
Operating temperature
4°~131° (
-
20°~55° C)
Parts List:
Sensor
Mounting surface
O
-
ring
Hex
n
ut
1x
IR proximity sensor
1x
Wiring harness
1x
Hex n
ut
1x
O
-
ring
1x
Manual
Hole size depends on the
particular model's diameter
NOTE
S
:
1. Only the front is IP65 rated. or weatherproof installation, the O-ring must be used as shown and the
area behind the mounting surface must be protected from moisture incursion.
2. To ensure proper operation, make sure no objects sit or come within 113/4" (30cm) (60° to the left and
right) of the front of the IR proximity sensor to avoid interference.

ENFORCER Infrared Proximity Sensors
SECO-LARM U.S.A., Inc. 3
Overview
:
IR Range and Trigger Time Settings:
Sample Wiring:
Wiring to an Alarm for Anti
-
T
heft*
Wiring to
a
n
N.O.
D
oor
S
trike for
Wave
-
to
-
Open
Egress
*Sensor covered (relay active) in normal state
Toggle mode
:
Set the trigger time
to maximum.
Near
19/16" (4cm)
Adjustable range
(Default: ar)
ar
6" (15cm)
Adjustable
trigger time
(Default: Short)
Short
(0.5s)
Long
(30s)
N.O. Output
N.C. Output
COM
Negative (–)
Positive (+)
+
–
(Red wire)
(Brown
wire)
(Green wire)
(Blue
wire)
(Purple
wire)
Power
Supply
Positive (+)
Electric
Door
Strike
N.C. Output
N.O. Output
COM
Negative (–)
(Red wire)
(Brown wire)
(Green
wire)
(Blue wire)
(Purple wire)
Power
Supply
Door Strike
Power Supply
†
Suggest c
onnect
ing
a
metal oxide varistor
(
MOV) and
diode (both
not included)
as close as possible and in parallel with
the controlled output
device. This absorbs possible electromagnetic interference to prevent damaging the IR proximity sensor.
Diode
†
MOV
†
Alarm
Control
Panel
(N.C. Input)
CS-PD422-PQ
CS-PD115-PAQ
CS-PD419-PQ
1
1
/
8
"
(28mm)
1
1
/
4
"
(31mm)
1
3
/
8
"
(35mm)
15
/
16
"
(24mm)
3
/
4
"
(19mm)
3
/
4
"
(19mm)
1
"
(25mm)
7
/
8
"
(22mm)
7
/
8
"
(23mm)
1
1
/
4
"
(31mm)
1
5
/
16
"
(33mm)
1
5
/
16
"
(34mm)
11
/
16
"
(
17
mm)
CS-PD438-PQ
1
5
/
8
"
(41mm)
1
1
/
2
"
(38mm)
9
/
16
" (15mm)
CS-PD115-PAQ
CS-PD419-PQ
CS-PD422-PQ
CS-PD438-PQ
LED
Ring LED
CS-PD115-PAQ
Other models

ENFORCER Infrared Proximity Sensors
4SECO-LARM U.S.A., Inc.
EXIT
Sample Applications:
Anti-Theft
Access Control
Place the sensor under
or behind
a valuable object. If the
object is removed from the sensor, the sensor will
trigger an
alarm to alert the owner that the item is out of place.
Mount the sensor to a wall or plate in a protected area.
A user
can wave his or her hand in front of the sensor to unlock an
electronic door lock, allowing germ-free, protected egress.
IR
Proximity
Sensor
IR Proximity
Sensor
NOTICE
:
The SECO-LARM policy is one of continual development and improvement. or that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for
misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM
U.S.A., Inc. All
rights reserved.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while
used in normal
service for one (1) year from the date of sale to the original customer. SECO-LARM
’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM
. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, ne
glect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM
determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship. The sole ob
ligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM
’s
option. In no event shall SECO-LARM
be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
SECO
-
LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
PITSW2
Phone: [phone] | [phone] Email: [e-mail]
MI_CS-PDxxx-PxQ_201008.docx
Order Part # 763-181-2%
IMPORTANT
:
Users and installers of this product are
responsible for ensuring that the installation and configuration of this
product complies with all national, state, and local laws and codes related to locking and egress devices. SECO-
LARM will
not be held responsible for the use of this product in violation of any current laws or codes.
Troubleshooting:
The indicator light is
continuously green
•Check that there are no objects in front of the sensor
•Adjust the sensor’s range to be shorter (see IR Range and Trigger
Time Settings on page 3)
•Check that the power supply’s voltage is 12~24 VDC
•Adjust the trigger time setting – a long delay or enabling toggle mode
could affect the sensor’s operation
The indicator light will not
turn green
•Adjust the sensor’s range to be longer (see IR Range and Trigger
Time Settings on page 3)
•Check that the power supply’s voltage is 12~24 VDC
Available Models:
CS-PD115-PAQ
CS-PD115-PAQ CS-PD419-PQ CS-PD422-PQ CS-PD438-PQ