ENFORCER Enforcer SD-927PKC-NEQ User manual

®
SD
-
927PKC
-
NEQ
Wave-To-Open Sensors
Manual
Features:
•
Dual voltage, 12~24 VAC/VDC
•Range a justable from 23/8"-8" (6~20 cm)
•Stainless steel single-gang plate
•3A relay, a justable from 0.5
~30 sec, toggle,
or as long as han is near the sensor
•LED illuminate sensor area for easy
i entification
•
Quick connect screw-less terminal block
•Selectable LED colors (turns from re to
green or green to re ) when activate
SD-927PKC-NEVQ
•A s manual overri e button as a backup
to the sensor
The ENFORCER Wave-To-Open Sensors use
IR technology to request egress from a protecte
area or activate a evice with the simple wave of a han . Since no touch is require
, this sensor is
i eal for use in hospitals, clinics, labs, cleanrooms (to re uce the risk of contamination), schools,
factories, or offices. The SD-927PKC-NEVQ a s a manual overri e button.
Also available with Spanish (SD-927PKC-NSQ, SD-927PKC-NSVQ) or French (SD-927PKC-NFQ
,
SD-927PKC-NFVQ) faceplates.
SD
-
927PKC
-
NEVQ

ENFORCER Wave-To-Open Sensors
2SECO-LARM U.S.A., Inc.
Model
SD
-
927PKC
-
NEQ
SD
-
927PKC
-
NEVQ
Operating voltage
12~24 VAC/VDC
Current raw (max.)
120mA@12VDC
Relay type
Form C ry contact, 3A@24VDC
Overri e
button
Switching capacity
N/A
3A@24VDC
Mechanical
life
N/A
500,000
cycles
Response time
10m
s
LEDS
Stan by
Re *
Triggere
Green*
Output time
A justable,
0.5
~30
sec.
, toggle,
or as long as sensor is triggere
Sensing range
A justable, 2
3
/
8
"~8" (6
-
2
0
cm)
Operating t
emperature
-
4
°~
131
° F (
-
20
°~
55
° C)
Weight
3
-
oz (85g)
3.9
-
oz (110g)
*Default, reversible by jumper
Specifications:
1.
Run four wires through the wall to a single
-
gang back
-
box.
2. Connect the four wires from the back-box to the quick
connect screw-less terminal accor ing to Fig. 1.
3. Screw the plate into the back-box, taking care not to crimp
the wires.
4. Remove clear protective film from the sensor before use.
djusting the LED Color:
1. The LED color factory efault setting is re (stan by) an
green (triggere ).
2. To reverse the LED color visual in icator to green (stan by)
an re triggere ), remove the jumper locate at the right
si e of the terminal block as shown in Fig. 2.
djusting the Sensor Range and Output Timer
1. To a just the sensor's range, turn the trimpot
counterclockwise ( ecrease) or clockwise (increase).
2. To a just the output time, turn the trimpot
counterclockwise ( ecrease) or clockwise (increase). To
set to toggle, turn the trimpot all the way counterclockwise.
1x
Wave
-
To
-
Open
Sensor
2x
Mounting screws
3x
6" (15cm)
wire
connectors*
1x
Manual
*For overri e button, SD-927PKC-NEVQ only
Parts List:
Installation:
Fig.
1
Connections
(un er back cover)
COM
NO
NC
Power Input
Relay output
(3A max.)
(
–
)
(
+
)
Sensor
range
potentiometer
Terminal block
Fig.
2
Output Time an Sensor
Range Potentiometers
LED Color
a justment jumper
Output
time
potentiometer

ENFORCER Wave-To-Open Sensors
SECO-LARM U.S.A., Inc. 3
(
–
)
(
+
)
COM
N
C
NO
NC
Relay output
12
~24 VAC/
VDC
Power input
3.Overri e Button Wiring (SD-927PKC-NEVQ only)
12~24 VDC (+)
Groun (-)
COM
N.O.
Blue wire: COM to N.C.
Purple wire: N.O.
Green wire N.C.
(–) (
+
)
COM
NO
NC
NC
NO
COM
12~24VDC
Power Supply
(–) (
+
)
Electric
Lock
(
–
)
(
+
)
N.O.
N.C.
OR
12~24 VDC (+)
Groun (
-
)
COM
Manual Overri e Button
Overri e button
COM
(with re ot)
shoul be connecte to the NC terminal
N.O.
Green: N
.
C
.
COM
NO
NC
T
he manual overri e button se
rves as a backup to the sensor
Purple
:
N.O.
Blue:
COM to N.C.
A re ot
in icates COM
1.Installation with Electric Lock
2. Installation with Electromagnetic Lock an Keypa
W VE TO
OPEN
Access Control Power Supply
SK
-
1011
-
S
D
Q
Digital Keypa
Tamper
Output (N.C.)
EGRESS
NO
COM
NC
SECO
-
LARM
Series
Electromagnetic Lock
(–) (+)
12
~24 VAC/
VDC
Power input
Relay output
COM
NO
NC
(+)
Sample
Installation
s
:
SECO
-
LARM
Series
Electric Strike
(Fail Secure)
W VE TO OPEN
Access Control
Power Supply
(
+
)
SECO
-
LARM
Series
Electromagnetic Lock
(Fail Safe)
SECO
-LARM
W VE TO OPEN

ENFORCER Wave-To-Open Sensors
4SECO-LARM U.S.A., Inc.
The SD
-
927P
KC
Series is esigne for
in oor
use to match most interiors. The sensor require
s
special care to ensure reliability an a long operating life.
1. Use a soft, clean cloth for cleaning.
2. Be careful not to spray liqui s irectly on the unit.
3. When cleaning, spray the cleaning solution onto the cleaning cloth instea of the unit.
4. Be sure to wipe off any excess liqui from the sensor. Wet spots or areas may affect the
sensor’s performance.
Overview:
NOTICE
:
The SECO
-
LARM policy is one of continual evelopment an
improvement. For that reason, SECO
-
LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All t
ra emarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A.,
Inc. All
rights reserve .
W RR NTY:
This SECO
-
LARM pro uct is warrante against efects in
material an workmanship while
use in normal
service for one (1) year from the ate of sale to the original customer. SECO-
LARM’s obligation is limite to the repair or
replacement of any efective part if the unit is returne , transportation prepai , to SECO-LARM.
This Warranty is voi if
amage is cause by or attribute to acts of Go , physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM etermines
that such equipment
is not operating properly as a result of causes other than efects in material an workmanship.
The sole obligation of
SECO-LARM an the purchaser’s exclusive reme y, shall be limite to the replacement or repair only, at SECO-LARM
’s
option. In no event shall SECO-
LARM be liable for any special, collateral, inci ental, or consequential personal or property
amage of any kin to the purchaser or anyone else.
IMPORT NT W RNING
:
Incorrect
mounting which lea s to exposure to rain or moisture insi e the enclosure coul cause
a angerous electric shock, amage the evice, an voi the warranty.
IMPORT NT
:
Users an installers of this pro uct are responsible for ensuring that the installati
on an configuration of this
pro uct complies with all national, state, an local laws an co es relate to locking an egress evices. SECO-
LARM will
not be hel responsible for the use of this pro uct in violation of any current laws or co es.
Care and Cleaning for the SD
-
927P
KC
Series
Wave
-
To
-
Open Sensor
:
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
PICPN3
MI_SD
-
927PKC
-
NExQ_200805. ocx
11/8"
(28mm)
21/8"
(55mm)
13/4"
(44mm)
11/8"
(28mm)
21/8"
(55mm)
13/4"
(44mm)
Si e View Back View Si e View Back View
SD-927-PKC-NEVQ
SD-927-PKC-NEQ
13/16"
(30mm)