ENFORCER E-931-S50RRLQ User manual

ENFORCER 50ft Large Reflective Beam Sensor
8SECO-LARM U.S.A., Inc.
NOTICE
:
The information and specifications printed in this manual are current at the time of publication.
However, the
SECO-LA M policy is one of continual development and improvement. For this reason, SECO-
LA M reserves the right to
change specifications without notice. SECO-LA M is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LA M U.S.A., Inc. All rights reserved.
This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LA M.
WARRANTY:
This SECO-
LA M product is warranted against defects in material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO-
LA M’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LA M.
This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-
LA M determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of
SECO-LA M and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-
LA M’s
option. In no event shall SECO-
LA M be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
SECO
-
LA
RM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA, 92606 Website: www.seco-larm.com PITSW3
Phone: [phone] | [phone] Email: [email protected] MiE-931-S50 LQ_1312.docx
Troubleshooting:
Sensor does not detect the object.
•
Check the sensor’s alignment.
•eadjust the sensor’s response time.
Alarm LED will not turn ON when the beam
is interrupted
•
Clean the sensor and reflector with a damp
(not wet) cloth.
•Adjust the reflector and/or sensor for proper
alignment.
Alarm LED turns ON
when object is
detected, but there is no output
•
Check wiring between the sensor and local
alarm device.
Alarm LED is continuously ON
•
Check the sensor’s alignment.
•Check for any objects between the sensor
and reflector that may be causing false
alarms.
Alarm output becomes erratic in bad
weather
•
Check the sensor’s alignment.
•eadjust the sensor’s response time.
Frequent false alarms from leaves, birds,
or other objects
•
eadjust the sensor’s response time.
•Change the sensor’s location.
This product is protected by the following patents: U.S. pat. no. D485774 Taiwan pat. no. 89463 China pat. no. ZL03311103.0
Other international patents are pending.
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify oHS-compliant products.
E-931-S5 RRLQ
50ft Large eflective Beam Sensor
Manual
•
Up to 50ft (15m) sensing range
•Weatherproof (IP55)
•Beam status LED
•
12~250 VAC/VDC Operation
•Form C relay rated 0.5A@120VAC
•N.C. Tamper switch rated 0.5A@30VDC
Patented

ENFORCER 50ft Large Reflective Beam Sensor
2SECO-LARM U.S.A., Inc.
Table of Contents:
Features
................................
.........................
2
Specifications ................................................. 2
Parts List ......................................................... 3
Dimensions ..................................................... 3
Overview ......................................................... 3
Choosing a Location ....................................... 4
Wiring Diagram ............................................... 4
Installation
................................
...................
5
-
6
Sample Installations ........................................6
Adjusting the esponse Time..........................7
Adjusting the Alignment ...................................7
Fine-Tuning the Sensor ...................................7
Troubleshooting ...............................................8
Warranty ..........................................................8
Features:
•
eflective beam provides reliable perimeter security, minimizing false alarms from falling
leaves, birds, etc.
•Lensed optics
reinforces beam strength and provides excellent immunity to false alarms due to
rain, snow, mist, etc.
•Weatherproof, sunlight-filtering case for indoor and outdoor use
•Large reflective beam sensor
•Long-range sensing: Up to 50ft (15m)
•NO/NC Alarm output
•Non-polarized power inputs, 12~250 VAC/VDC
•esponse time adjustable for nearly all situations
•Includes hoods for sensor and reflector
Specifications:
Model
E
-
931
-
S5 RRLQ
Type
50’ Large eflective Beam Sensor
Sensing range
50
’
(15m)
Response time
50~70
0
ms (Programmable)
Current draw
100mA
LEDs
Red
No beam signal, triggered
Yellow
Poor beam signal
Green
Connected to power
Operating voltage
12~250 VAC/VDC
Alarm output
NO/NC elay,
0.5
A@120VAC, min. 1s
Tamper output
N.C. Switch,
0.5
A@
30VDC
IP Rating
IP55
Alignment angle
Horizontal: ±90°,
Vertical: ±
5°
Operating temperature
-
13°~131° F (
-
25°~55° C)
Weight
Sensor
14.5
-
oz (
410
g) (with hood)
Reflector
8
.
8
-
oz (
250
g) (with hood)
Material
PC esin
ENFORCER 50ft Large Reflective Beam Sensor
SECO-LARM U.S.A., Inc. 7
Adjusting the Response Time:
The sensor’s response time can be adjusted by turning the response time adjustment knob.
esponse time can be adjusted according to how quickly an object breaks the sensor beam.
NOTE: A faster response time increases the chance of a false alarm. A slower response time
increases the chance of missing a broken beam.
50ms
700ms
350ms
B
A
C
Adjusting the Alignment:
The
sensor can be adjusted ±
5° vertically and ± 90° horizontally once the unit is mounted and
power is connected.
1. emove the sensor cover and look into one of the alignment viewfinders (located between
the two lenses) at a 45° angle.
2. Adjust the horizontal and vertical angles of the lens until the reflector is clearly seen in the
viewfinder.
3. eplace the sensor cover.
Viewfinder
Horizontal adjustment
Vertical adjustment
unning (fast)
A
B
C
Walking
(normal)
Slow Walking (slow)
Fine
-
Tuning the Sensor:
Once the sensor is mounted and aligned, the sensor can be
fine-tuned using the voltage output jack.
1. Set the range of a volt-ohm meter (VOM) to 1~10 VDC.
2. Insert the red (+) probe into the (+) terminal and the black
(–) probe into the (–) terminal.
3. Measure the voltage (see table).
4. Adjust the horizontal and vertical angles until the VOM
indicates the highest voltage.
NOTE: Do not interrupt the beam while adjusting alignment.
Posi
tive (
+
)
Nega
tive (
–
)
Voltage output
Alignment Quality
>
2.8
Best
2
.
1
~2.7V
Good
1.2~2.0V
Fair
<1.1V
e
-
adjust

ENFORCER 50ft Large Reflective Beam Sensor
6SECO-LARM U.S.A., Inc.
L
-
Shaped Mounting Bracke
t
(
Reflector
):
1. Loosen the captive screw at the bottom of the reflector. Slide the mounting plate downwards
and remove it from the unit.
2. Using the included short screws, attach the L-shaped mounting bracket to the mounting plate
(fig. 5). Secure the bracket to the wall or surface using the included mounting screws. Use
optional anchors for brick or drywall (not included).
3. Slide the reflector into position on the mounting plate and secure them in place by tightening
the captive screw.
Installation
(continued)
Sample Installations:
Configuration 1 Configuration 2 Configuration 3
1.
Configuration 1: Sensor and reflector are mounted facing each other.
2. Configuration 2: Sensor and reflector are mounted on perpendicular surfaces.
3. Configuration 3: Sensor and reflector are mounted on parallel surfaces, but the units are
mounted perpendicular. The reflector is mounted with the L-shaped bracket.
Top View
Side View
Top View
Side View
Top View
Side View
Fig. 5
ENFORCER 50ft Large Reflective Beam Sensor
SECO-LARM U.S.A., Inc. 3
Overview:
Sensor Reflector Cover
Signal LED
esponse time
adjustment
knob
Horizontal
adjustment
bracket
Lens
Terminals
Alarm LED
Voltage
output
probes
Vertical
adjustment
screw
Alignment
viewfinder
Captive
screw
Cover screw
Power LED
Parts List:
1x
Sensor
1x eflector
2x Hoods
2x Mounting plates
2x Mounting brackets
2x Pole mounting brackets
1x L-Shaped mounting bracket
4x Mounting screws
4x Long screws
6x Short screws
1x ubber gasket
Dimensions:
Sensor with hood Reflector with hood
3
3
16
” (81mm) 3
9
16
” (91mm)
7
3
16
”(182mm)
3
3
16
” (81mm) 3
9
16
” (91mm)

ENFORCER 50ft Large Reflective Beam Sensor
4SECO-LARM U.S.A., Inc.
Choosing a Location:
To prevent erratic operation and/or false alarms:
•Wind will not directly cause false alarms, but
could cause leaves or similar objects to fly or
wave into the beams. Therefore, do not mount
near trees, bushes or other leafy vegetation.
•Do not mount where the sensor could be
suddenly exposed to a bright light, such as a
floodlight or a passing automobile’s headlights.
Over time, a strong light can affect the life of the
sensor.
•Do not let sunlight or any direct beam of light
enter the sensor. If needed, mount so the
reflector, not the sensor, faces the sun.
•Do not mount where animals could break the
beams.
•Do not mount where the sensor could be
splashed by water or mud.
Do not
install the sensor in areas where it may be
splashed by water or direct sea spray.
Do not mount the sensor near trees, bushes or
other leafy vegetation.
Wiring Diagram:
•
Polarity does not matter for the power input
•Connect the N.C. tamper terminal to the tamper circuit of an alarm control panel
1
2
3
4
5
6
7
(+)
(
–
)
COM
N.C.
N.O.
N.C.
N.C.
12~250 VAC/VDC
Alarm
Output
Tamper Output
Avoid strong lights such as the sun or automobile
headlights shining directly on the sensor.
ENFORCER 50ft Large Reflective Beam Sensor
SECO-LARM U.S.A., Inc. 5
Installation:
Wall Mount (Sensor):
1. Loosen the cover screw at the bottom of the sensor and remove the cover (fig. 1).
2.
Loosen the captive screw at the bottom of the sensor. Slide the mounting plate downwards and
remove it from the unit.
3. Make a small hole in the rubber grommet.
4. Pull the wires from the wall or pole through the grommet and then through the opening above
the terminals (fig. 2).
5. Connect the wires to the terminals. See Wiring Diagram on page 4.
6. Using the included mounting screws, secure the mounting plate to the wall or surface (fig. 3).
Use optional anchors for brick or drywall (not included).
7. Slide the sensor into position on the mounting plate and secure it in place by tightening the
captive screw.
8. eplace the cover and secure it by tightening the cover screw.
Wall Mount (Reflector):
1. Loosen the captive screw at the bottom of the reflector. Slide the mounting plate downwards
and remove it from the unit.
2. Using the included mounting screws, secure the mounting plate to the wall or surface. Use
optional anchors for brick or drywall (not included).
3.
Slide the reflector into position on the mounting plate and secure it in place by tightening the
captive screw.
Fig. 1
Pole Mount (Sensor and Reflector):
1. Use a pole with a diameter of 1
1
/
2
” (38mm) to 1
3
/
4
” (45mm).
2. Fix mounting bracket to the pole with the pole bracket using
the included long screws.
3. emove the mounting plate from the back of the sensor and
reflector units (fig. 4).
4. Secure the mounting plate of the unit to the mounting bracket
using the included short screws.
5. Slide the sensor and reflector into position on the mounting
plate and secure them in place by tightening the captive screw.
(Continued on next page.)
Fig. 2
Fig. 4
Fig. 3