ETEKCITY EMT-100 User manual

User Manual of Product 1:
Etekcity Food Kitchen Scale, Digital Weight Grams and Oz for
Cooking, Baking, Meal Prep, and Diet, Medium, Carbon Black
User Manual of Product 2:
Etekcity EMT100 Digital Instant Read Meat Thermometer,
5"Long Probe, Black

1
Digital
Kitchen Scale
Model: EK8060
User Manual
Questions or Concerns?
Mon–Fri, 9:00 am–5:00 pm PST/PDT
[e-mail] • [phone]

2
If you have any questions or concerns, please reach out to our helpful Customer
Support Team at [e-mail]. We hope you enjoy your new
kitchen scale!
Thank you for purchasing the
Digital Kitchen Scale by Etekcity.

3
Table of Contents
Package Contents
Specifications
Important Safety Information
Function Diagram
Symbols
Using Your Scale
• General Operation
• Zero / Tare Function
• Unit Conversion
• Automatic Power Off
• Manual Power Off
Replacing the Batteries
This product contains a coin/
Button battery
Troubleshooting
Warranty Information
Customer Support
3
3
4
5
5
6
6
7
8
8
8
8
9
10
11
13
Specifications
Package Contents
Weight Capacity 176 oz / 11 lb / 5000 g / 5000 mL
Units oz / lb:oz / fl’oz (water/milk) / g / mL (water/milk)
Increments 0.04 oz / 1 g / 1 mL
Auto-Off 180 seconds
Battery 2 x 3V CR2032 batteries
Dimensions 8.3 x 6.3 x 0.6 in / 21 x 16 x 1.6 cm
1 x Digital Kitchen Scale
2 x 3V CR 2032 Batteries (Pre-Installed)
1 x Quick Start Guide

4
• Always place the scale on a hard, dry, and flat surface before measurement in
order to ensure accuracy.
• Do not exceed the 11 lb / 5000 g weight capacity as it will damage the scale. An
error indicator will appear on the LCD display if the limit is exceeded.
• Do not immerse the scale in water or any liquid. If liquid is spilled on the digital
display or buttons, immediately wipe the scale dry with a soft cloth to avoid internal
damage.
• Handle with care. This scale is not intended for commercial or heavy-duty use.
• Keep the scale in a cool, dry place. Avoid exposure to damp environments or extreme
temperatures.
• Household use only.
• Do not mix new and old batteries.
• If the low battery indicator “ “ appears on the display, replace the batteries.
• If the scale is not in use for an extended period of time, remove the batteries to conserve
battery life and extend the lifetime of the scale.
Important Safety Information
READ AND SAVE
THESE INSTRUCTIONS
To avoid damage to this scale, please read and follow all instructions
and safety guidelines in this manual.
Scale
Batteries

5
Function Diagram
A. Unit Selection Button
B. LCD Display
C. Power/Tare Button
A
BC
D
F
E
D. Battery Compartment
E. Screw
F. Anti-Skid Pads
Symbols
Solids Water (Liquid) Milk (Liquid)

6
Using Your Scale
Note:
• For accurate results, always place the scale on a hard, dry, flat surface, and keep
the scale away from dirt, dust, vibrations, wind, air currents, and electromagnetic
interference.
• When you turn on the scale, choose units, or use the tare function, wait for the display to
read before measuring.
• The batteries are pre-installed in the scale. Turn the scale over and pull the plastic
strip out from the battery compartment.
General Operation
1. Place the scale on a hard, flat, level surface.
2. Press TARE to turn on the scale. Make sure the display reads . Press UNIT to
select your desired measuring unit, which will show at the bottom of the display.
3. Place your item on the scale.
4. Wait for the reading on the display to stabilize.

7
Zero / Tare Function
1. Press TARE to turn on the scale. Make sure the display reads . If the screen does
not display automatically, press TARE to adjust to zero.
2. Place the container on the center of the scale.
3. Wait for the reading on the display to stabilize. The display will show the container’s
weight.
4. Press TARE to tare the weight of the container. The screen should now display .
5. Place the liquid or items into the container. The scale will measure the contents without
including the weight of the container. [Figure 1.1]
6. When you’re done, reset the scale by removing all weight and pressing TARE again.
Whenever you measure items inside a container, you can use the tare function to remove the
container’s weight from the final measurement.
Figure 1.1

8
Unit Conversion
Automatic Power Off
Manual Power Off
To change the unit of measurement, press UNIT until the display shows the desired unit of
measurement.
To save battery power, the scale will automatically power off after 180 seconds of inactivity.
Press and hold TARE for 2 seconds to turn off the scale.
Replacing the Batteries
1. Turn the scale over and use a screwdriver to loosen the screw of the battery compartment.
2. Take out the used batteries and replace them with 2 new 3V CR2032 batteries.
3. Replace the battery compartment cover and screw it shut.

9
This product contains a coin/Button battery
KEEP OUT OF REACH OF CHILDREN
Swallowing can lead to chemical burns, perforation of soft tissue, and death.Severe burns can occur within
2 hours of ingestion.Seek medical attention immediately.
• Place sticky tape around both sides of the battery and dispose of it immediately in an outside bin or
recycle safely
• Store spare batteries securely
• recycling units emptied on a regular basis
• use of opaque containers – to keep the batteries out of view;
Unfortunately, it is not obvious when a button or coin battery is stuck in a child’s oesophagus (food pipe).
The child might:
• cough, gag or drool a lot;
• appear to have a stomach upset or a virus;
• be sick;
• point to their throat or stomach;
• have a pain in their abdomen, chest or throat;
• be tired or lethargic;
• be quieter or more clingy than usual or otherwise “not themselves”;
• lose their appetite or have a reduced appetite;
• not want to eat solid food / be unable to eat solid food.
These sorts of symptoms vary or fluctuate, with the pain increasing and then subsiding.
A specific symptom to button and coin battery ingestion is vomiting fresh (bright red) blood. If the child
does this seek immediate medical help.
The lack of clear symptoms is why it is important to be vigilant with “flat” or spare button or coin
batteries in the home and the products that contain them.

10
Troubleshooting
Problem Possible Solution
Scale does not turn on.
Open the battery compartment cover and remove the plastic strip.
Replace the batteries (see page 8).
Make sure batteries are inserted under the correct polarity as
marked in the battery compartment.
Reading is inaccurate.
Place the scale on a hard, dry, and flat surface.
Make sure the screen displays before measuring (see Zero
/ Tare Function, page 7).
Remove the batteries for 45 seconds, then replace them to reset the
scale.
Display shows Item is too heavy. Remove item from scale to protect its weight
sensors. Use a different scale with a higher weight range.
Display shows Calibration error. Turn the scale off and on again. Avoid moving the
scale while measuring.
Display shows Battery power is low. Replace the batteries
(see page 8).
If your problem is not listed, please contact Customer Support (see page 13).

11
Warranty Information
Terms & Policy
Etekcity Corporation (“Etekcity”) warrants this product to the original
purchaser to be free from defects in material and workmanship, under
normal use and conditions, for a period of 2 years from the date of original
purchase.
Etekcity agrees, at our option during the warranty period, to repair any
defect in material or workmanship or furnish an equal product in exchange
without charge, subject to verification of the defect or malfunction and
proof of the date of purchase.
There is no other express warranty. This warranty does not apply:
• If the product has been modified from its original condition;
• If the product has not been used in accordance with directions and
instructions in the user manual;
• To damages or defects caused by accident, abuse, misuse or improper or
inadequate maintenance;
• To damages or defects caused by service or repair of the product
performed by an unauthorized service provider or by anyone other than
Etekcity;
• To damages or defects occurring during commercial use, rental use, or
any use for which the product is not intended;
• To damages or defects exceeding the cost of the product.
Product Digital Kitchen Scale
Model EK8060
Default Warranty Period 2 years
For your own reference, we strongly recommend that you record your order ID and date of
purchase.

12
Etekcity will not be liable for indirect, incidental, or consequential damages
in connection with the use of the product covered by this warranty.
This warranty extends only to the original consumer purchaser of the
product and is not transferable to any subsequent owner of the product
regardless of whether the product is transferred during the specified term of
the warranty.
This warranty does not extend to products purchased from unauthorized
sellers. Etekcity’s warranty extends only to products purchased from
authorized sellers that are subject to Etekcity’s quality controls and have
agreed to follow its quality controls.
All implied warranties are limited to the period of this limited warranty.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
If you discover that your product is defective within the specified warranty
period, please contact Customer Support via [e-mail]. DO
NOT dispose of your product before contacting us. Once our Customer
Support Team has approved your request, please return the product with a
copy of the invoice and order ID.
Every Etekcity product automatically includes a 2-year warranty. To make
the customer support process quick and easy, register your product online
at
www.etekcity.com/warranty.
This warranty is made by:
Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806, USA
CAN ICES-003 (B) / NMB-003 (B).

13
Customer Support
If you have any questions or concerns about your new product, please contact our helpful
Customer Support Team.
Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Email: [e-mail]
CUSTOMER SUPPORT
SUPPORT HOURS
Toll-Free: [phone]
Mon–Fri, 9:00 am–5:00 pm PST/PDT
*Please have your order invoice and order ID ready before contacting
Customer Support.

Building on better living.
01.02_D_23D04_us

1
Questions or Concerns? [e-mail] • [phone]
Digital Meat Thermometer
Model: EMT-100
User Manual
HOLD
°C/°F

2
Thank you for purchasing the Digital
Meat Thermometer by Etekcity.
If you have any questions or concerns,
please reach out to our helpful Customer
Support Team at suppo[email protected].
We hope you enjoy your new thermometer!

3
Table of Contents
Package Contents
Specifications
Features
Warnings
Function Diagram
Operation
Temperature Reference Guide
Tips
Cleaning
Warranty Information
Customer Support
3
3
4
4
4
5
6
8
8
10
12
Specifications
Measurement Range -58°–572°F / -50°–300°C
Measurement
Accuracy
±2°F at -4°–302°F / ±1°C at
-20°–150°C
Resolution 0.1°
Units °F / °C
Waterproof Level IP66
Backlight Auto-Off 10 seconds
Device Auto-Off 10 minutes if no buttons are
pressed
Battery CR2032 Li-ion Button Cell
Rated Power 3V
Case Material Heat and impact resistant
eco-friendly ABS plastic
Probe Material Food-grade 304
stainless steel
Device Dimensions 8.9 x 1.3 x 0.9 in /
225.5 x 32.3 x 21.7 mm
Response Time 2–4 seconds
Package Contents
1 x Digital Meat Thermometer
1 x Quick Start Guide
1 x Temperature Reference Guide
1 x 3V Li-ion Button Cell Battery

4
HOLD °C/°F
Warnings
• Do not leave the thermometer in the oven while
cooking.
• Do not touch the hot probe with bare hands.
• Not intended for use by children aged 12 or
under.
• Internal magnet allows thermometer to stick to
metal surfaces
• Unit switching
• Backlight can be turned on/off
• Hold Temperature function stops the display
from changing the readout
Features Function Diagram
A. Temperature Probe
B. Probe Cover
C. Thermometer Body
D. LCD Display
E. Power/Hold Temperature Button
F. Backlight/Unit Switching Button
G. Battery Compartment
A
B
C
G
DE F

5
1. Before using the thermometer, peel the
protective film off the display.
2. To turn on the thermometer, press and hold the
button for 2 seconds. The LCD screen will
turn on, display all options, and then display the
current probe temperature.
Operation
Note: The default display unit is Fahrenheit.
To change to Celsius, press and hold the
button for 2 seconds. Press and hold again to
change back to Fahrenheit.
3. Remove the probe cover. Insert the probe into
the food being cooked. The thermometer will
measure the internal food temperature.
4. To hold the temperature on the display, press
the button while the probe is still inserted
into the food being cooked. The current
temperature will remain on the display until the
button is pressed again.
5. To light up the LCD display, press the
button. To turn off the backlight, press
the button again. The light will turn off
automatically after 10 seconds.