ETEKCITY FIT 8S User manual

1
Smart Fitness Scale
Balance de tness intelligente
Model ·Modèle:FIT 8S
User Manual ·Guide d’utilisation
Questions or Concerns? ·Guide d’utilisation
Mon–Fri, 9:00 am–5:00 pm PST/PDT · Du lundi au vendredi de 9h à 17h (UTC-8/UTC-7)
[e-mail] • [phone]

2
Table of Contents
Package Contents
Specications
Safety Information
Function Diagram
Digital Display
VeSync App Setup
Before First Use
Using the Smart Scale
Using the App
Maintenance
Troubleshooting
Warranty Information
Customer Support
5
5
6
8
9
10
11
11
14
15
18
21
23

3
Table des matières
Contenu de l’emballage
Caractéristiques techniques
Consignes de sécurité
Schéma des fonctions
Écran numérique
Conguration de l’application VeSync
Avant la première utilisation
Utilisation de la balance intelligente
Utilisation de l’application
Entretien
Dépannage
Informations relatives à la garantie
Service à la clientèle
25
25
26
29
30
31
32
32
34
35
38
41
43

4
Thank you for purchasing the
Smart Fitness Scale by Etekcity.
If you have any questions or concerns, please reach out to our
helpful Customer Support Team at [e-mail].
We hope you enjoy your new smart tness scale!

5
Specications
Package Contents
Weight Capacity 180 kg / 28 st / 400 lb
Increments 0.05 kg / 0.1 lb
Weight Units kg / st / lb
Platform Tempered Glass
Dimensions 26 x 26 x 2.1 cm /
10.2 x 10.2 x 0.8 in
Battery 3 x 1.5V AAA Batteries
Auto-Off 30 seconds
1 x Smart Fitness Scale
3 x 1.5V AAA Batteries (Pre-Installed)
1 x Quick Start Guide

6
Safety Information
• This scale should not be used to diagnose or treat any medical
condition.
• Scale data should not be used as a substitute for medical advice
from a healthcare professional.
• This scale uses a harmless electrical current to measure body fat.
Consult a healthcare professional before using the smart scale if
you use medical electronic equipment such as a pacemaker.
• Check the scale before using. Do not use the scale if it is damaged
in any way.
• Do not strike or hit the scale. Do not use the scale if the glass
is cracked or broken. Due to the nature of tempered glass, the
glass will shatter if there is even a slight crack. If you see a crack,
Please read and follow all instructions and safety guidelines in
this manual.
READ AND SAVE THESE INSTRUCTIONS
Medical
General Use

7
contact Customer Support immediately (page 23).
• The glass platform is slippery when wet. Always make sure
the platform and your feet are dry before stepping on for
measurement.
• Place the scale on a hard, at surface to avoid tipping.
• To weigh safely and accurately, stand with your feet shoulder-
width apart while on the scale. Do not stand on the edge of the
scale or jump on the scale.
• Avoid standing on the scale for a long period of time, or when not
weighing yourself.
• Do not overload the scale. Maximum weight capacity is
180 kg / 28 st / 400 lb.
• Keep the scale in a cool area with low humidity. Keep the scale
away from heat sources, such as ovens or heaters. Avoid
temperature uctuations. Store the scale in a horizontal position,
not a vertical position.
• Handle with care.
• Not for commercial use. Household use only.
• Do not mix new and old batteries.
• If the low battery indicator (“Lo”) appears on the display, replace
the batteries.
• If the scale is not in use for a long period of time, remove the
batteries to extend the lifetime of the scale.
Batteries

8
Function Diagram
A. Weighing Platform
B. Display
C. Anti-Skid Padding
D. Unit Switching
Button
E. Battery Compartment
B
A
C
D
E

9
Digital Display
A. Weight Measurement
B. Wireless Connection Icon
C. Weight Units
A
C
B

10
VeSync App Setup
1. To download the VeSync app, scan the QR code or search
“VeSync” in the Apple App Store®or Google Play™ Store.
Note: Due to app updates and improvements, the contents of this manual may
change without notice. The VeSync app user interface may appear slightly
different.
Note:
• This scale uses the VeSync app, not the VeSyncFit app.
• For Android™ users, you may need to select Allow to use VeSync.
2. Open the VeSync app. If you already have an account, tap Log
In. To create a new account, tap Sign Up.
Note: You can change the name and icon at any time in the smart
tness scale settings.
3. Make sure your phone has Bluetooth®turned on.
4. Tap + in the VeSync app and select your smart tness scale.
5. Follow the in-app instructions to connect to your smart tness
scale.

11
Before First Use
1. Open the battery compartment on the underside of the scale.
Remove the included AAA batteries.
2. Remove the plastic insulator strip from the battery
compartment.
3. Replace the batteries. Follow the guidelines in the battery
compartment to match the +and –terminals.
Using the Smart Scale
Note:
• If you are pregnant, scale measurements will not be accurate.

12
Weighing Without the VeSync App
1. Place the scale on a hard, at surface. [Figure 1.1]
2. Step on the scale, then step off. Wait for the screen to display
“0.0” before using.
3. Place dry, bare feet on the scale’s conductive areas. Stand on
the scale until the display ashes several times, showing your
nal measurement. [Figure 1.2]
[Figure 1.1]
[Figure 1.2]

13
1. To change the unit of measurement (kg, lb, or st), step on the
scale to turn it on. Then, turn the scale over and press the
unit conversion button on the underside. To keep the settings
consistent, make sure the scale is connected to the VeSync
app. [Figure 1.3]
2. The default unit is pounds (lb). After changing units, the scale
will show the new unit of measurement.
[Figure 1.3]
Switching Units

14
Using the App
If you are a new user, you will need to enter your physical information
before weighing yourself for the rst time so the scale can calculate
your body metrics.
Note:
• Entering inaccurate information will make the scale’s measurements
less accurate.
• If you don’t identify with the available gender options, or are unsure,
pick the choice that you think best physically matches you. This
choice is used for physical measurements, such as body fat
percentages.
Creating a User

15
Maintenance
If the scale has been moved or ipped upside down, it must be
cleared to ensure accurate results.
Clearing the Scale
1. Place the scale on a hard, at surface.
2. Step on the scale until digits appear on the display, then step
off. [Figure 2.1]
3. The scale will show “ ” when cleared. [Figure 2.2]
[Figure 2.1] [Figure 2.2]

16
Cleaning the Scale
Replacing the Batteries
• Use a slightly damp cloth to clean the surface of the scale,
followed by a soft, dry cloth to wipe away any remaining
moisture.
• Do not use chemical or abrasive cleaning agents to clean the
scale.
1. Open the battery compartment on the underside of the scale.
2. Remove the old batteries and dispose of them properly.
3. Install 3 new 1.5V AAA batteries. Follow the guidelines in the
battery compartment to match the +and –terminals.
4. After closing the battery compartment, clear the scale (see
Clearing the Scale, page 15).
The display will show “Lo” when the batteries need to be replaced.

17
Display Messages
Wireless Connection Change Battery
Overload
Clearing

18
Troubleshooting
The scale doesn’t turn on.
• Check if the batteries are properly installed. If using the scale for
the rst time, remove the plastic insulator strip from the battery
compartment.
Information ashes on the screen and then disappears.
• The batteries are low and may need to be replaced.
The smart scale can’t be added to the VeSync app.
1. Please conrm the following things before pairing:
• The scale should only be connected to your phone via the VeSync App.
Please do not connect the scale to your phone’s Bluetooth®settings.
• Allow VeSync to access your Bluetooth® in your phone settings.
• Your scale and phone are within 30 ft (10 m) of each other.
• The scale is not currently connected to any other phone or app.
• Your phone’s operating system is running on iOS® 12.0+ or Android
6.0+.
• You’re using the latest version of the VeSync App.
• Turn off VPN (please ignore it if you are not using it).
Note:
• For Andriod 12+ users, make sure that you turn on the nearby device
permission and Bluetooth®to scan the target device. For users
whose Android system is below Andriod 12, make sure that turn on
location and Bluetooth®to scan the target device.

19
My scale only measures my weight, not my body fat or other metrics.
• Set up your smart scale in the VeSync app. Your weight will show on
the scale display, and more results will show on the app.
• Make sure Bluetooth®is turned on.
• If you’re wearing shoes or socks, the scale cannot measure health
metrics such as body fat. Step on the scale with bare feet.
2. Try the following steps to pair your scale and your phone:
• Enable Bluetooth® on your Phone.
• Light up the scale and keep it on.
• Open the Vesync App, and click “Add Device” or “+” on the top right
corner of the home page. Choose “Health” to select your device model,
and then follow the APP guides.
Note: Make sure to choose the right device model(you can nd it on
the back of the scale), or it will lead to a connection failure.
The data can’t be synced to the VeSync app.
1. When the scale turns off, it will enter into power-saving mode and the scale
and app will be disconnected. To sync data to the app properly, you need
to reconnect the scale and the app through the following steps:
• Restart the Bluetooth® of your phone.
• Light up the scale and keep it on, then open the APP to enter the
weighing homepage, wait for the Bluetooth®connection to be
successful, then weigh on the scale.
2. Reset your scale or restart the Bluetooth® of your Phone:
• Remove the batteries for 5-10 seconds, then put them back in.
• Try restarting your phone’s Bluetooth® after restarting the phone.
• Try the methods in solution 1 again.
3. Bluetooth®detection:
• Open the APP to enter the weighing homepage, click “Setting” on the
top right corner, then “Troubleshooting”, and “Start Testing” to detect
Bluetooth® anomalies.

20
Note: If the scale has errors on the display, will not turn off automatically, or
has a problem not listed here, try removing the batteries for 3 seconds, then
replacing them.
If you still need help, please contact Customer Support (page 23).
IC Statement
Radiation Exposure Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
This equipment complies with IC RSS‐102 radiation exposure limits set forth for an
uncontrolled environment.
• If your feet are too dry or too wet, the biometrics may not be detected.
Since skin can become very dry during winter, please also try to
apply some lotion or have a foot soak when it cannot measure other
measurement values.