Eterna OH157 User manual

Pack contents:
1 x Oil lled heater c/w 13A. fused,
3 pin plug tted
2 x Heater wheel clamping plates
4 x Castor wheels
4 x Dome nuts
2 x U clamping bolts
4 x U clamp securing wing nuts
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
Model:
OH157
1.5kW 7 Fin Oil Filled Heater
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
Issue 2014
FOR PRODUCT ADVICE:
• T: 01933 673 144
• F: 01933 678 083
• E: [email protected].uk
Visit our website:
www.eterna-lighting.co.uk
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
CLEANING:
Always remove the plug from the electrical socket
and allow the heater to cool down before cleaning
the heater.
Wipe heater with a soft dry cloth.
Wind the cable around the cable tidy and store the
heater in a clean dry place.
Do not try to repair the heater yourself, always
consult a suitably qualied engineer.
CLEANING WARNING:
Do not immerse the heater in water.
Do not use any cleaning chemicals such as
detergents and abrasives.
Do not allow the interior to get wet.
SPECIFICATION:
VOLTAGE: 220 – 240V – 50Hz
POWER MAX: 1.5kW
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
For breakage information visit:
www.eterna-lighting.co.uk
WARNING!
WHEN IN USE THIS PRODUCT CONTAINS HOT LIQUID.
Before each use the user must make a physical inspection to ensure
there is no damage to the metal case of the product.

READ THIS FIRST:
Check the pack and make sure you have all of the parts
listed on the front of this booklet. If not, contact the
supplier where you bought this product.
IMPORTANT SAFEGUARDS:
When using an electrical appliance, basic safety
precautions should always be observed, including the
following:
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Extreme caution is necessary where children or
persons with reduced physical, sensory or mental
capabilities may come into contact with the heater
when in use.
This heater is hot when in use. To avoid burns and
personal injury, do not let bare skin touch hot surfaces.
Never leave the heater unattended whilst it is in use.
The product is for household/oce use only.
In order to avoid overheating when in use, do not
cover the heater or position where it may come in
contact with ammable materials, such as curtains,
drapes etc. to avoid the risk of re.
This heater is lled with a precise quantity of special
oil. In case of leakage or repair which requires opening
of the oil container this should only be carried out by
the manufacturer or qualied engineer.
The heater must not be located adjacent to or against
an electrical socket.
Do not run the cord under carpets/rugs.
Arrange the cord away from high trac areas and
where it will not present a trip hazard.
Do not operate the heater with a damaged cord/plug
or if the heater malfunctions.
If the supply cord is damaged, it must be replaced by
qualied engineer.
Avoid the use of an extension cord as this may
overheat and cause a risk of re.
Use the heater in a well ventilated area.
Do not use the heater in any areas where petrol, paint
or other ammable liquids are stored e.g. garages or
workshops.
Do not use this heater in the immediate surroundings
of a bath, shower, swimming pool or where water is
present.
WARNING:
Only operate the heater in an upright position with
the feet attached, any other position could cause
malfunction.
When in use this product contains hot liquid.
Before each use the user must make a physical
inspection to ensure there is no damage to the metal
case of the product.
ASSEMBLY INSTRUCTIONS:
YOU MUST ATTACH THE FEET BEFORE OPERATING
THE HEATER.
1. Place the radiator upside-down on a scratch-free
location, making sure it is stable and will not fall.
2. To attach the castors to the mounting plate, unscrew
domed nut and feed through the holes in each end
of the mounting plate. Screw domed nut back in
place (g. 1) ensuring that they are fully tightened.
3. Unscrew wing nut from the U-shaped bolt (g. 2).
Hook U-shaped bolt onto the radiator between the
rst two ns (see g. 3).
4. Feed castor mounting plate on to the U-shaped bolt.
(g. 4).
5. Screw wing nut on to ends of U-shaped bolt and
fasten securely (g. 4). Over tightening may cause
damage to the radiator.
6. Now fasten second castor mounting plate between
last two ns (g. 5) and by repeating the above
steps.
INSTRUCTIONS FOR USE:
WARNING: WHEN IN USE THIS PRODUCT
CONTAINS HOT LIQUID.
BEFORE EACH USE THE USER MUST MAKE A
PHYSICAL INSPECTION TO ENSURE THERE IS NO
DAMAGE TO THE METAL CASE OF THE PRODUCT.
NOTE: When the heater is turned on for the rst time
or after having not been used for a long period, it may
smell for a short while.
1. Position the heater on a at and stable surface.
2. Set all controls to OFF and insert the plug into an
electrical socket.
3. Rotate the thermostat knob clockwise to MAX
position and switch the heater on as follows:
I = Low heat (600W)
II = Medium heat (900W)
I + II = High heat (1.5kW)
4. When your room reaches the desired temperature,
slowly rotate the thermostat knob counter clockwise
until the red indicator light goes out. The thermostat
can now be left at this setting. As soon as the room
temperature has dropped below the set temperature,
the unit will switch itself on automatically until the set
temperature has been reached again. In this way the
room temperature remains constant with the most
economical use of electricity.
5. To change the room temperature setting, rotate the
thermostat knob clockwise to raise the temperature,
or anti-clockwise to lower it.
6. This heater includes an overheat protection system
that shuts o the heater when parts of the heater get
excessively hot.
7. This unit is tted with anti-tip cut-out protection.
Should the unit not be in the correct vertical position,
the heater will shut o.
8. To completely shut the heater o, turn all the controls
to OFF, and remove plug from the electrical socket.
Fig 1 Fig 2
Fig 3
Fig 4
Fig 5