Eterna OH211T User manual

Pack contents:
1 x Oil lled heater c/w 13A. fused,
3 pin plug tted
2 x Heater wheel clamping plates
4 x Castor wheels
4 x Dome nuts
2 x U clamping bolts
4 x U clamp securing wing nuts
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
Model:
OH211T
2kW 11 Fin Oil Filled Heater With Timer
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
Issue 2015
FOR PRODUCT ADVICE:
• T: 01933 673 144
• F: 01933 678 083
• E: [email protected].uk
Visit our website:
www.eterna-lighting.co.uk
Made in China
CLEANING:
Always remove the plug from the electrical socket
and allow the heater to cool down before cleaning
the heater.
Wipe heater with a soft dry cloth.
Wind the cable around the cable tidy and store the
heater in a clean dry place.
CLEANING WARNING:
Do not immerse the heater in
water.
Do not use any cleaning chemicals
such as detergents and abrasives.
Do not allow the interior to get
wet.
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
SOME PARTS OF THIS
PRODUCT CAN BECOME
VERY HOT AND CAUSE
BURNS. PARTICULAR
ATTENTION HAS TO BE
GIVEN WHERE CHILDREN
AND VULNERABLE
PEOPLE ARE PRESENT.
CAUTION!
Children of less than 3 years should be kept away from the
heater unless continuously supervised.
Children aged from 3 years and less than 8 years shall only
switch on/o the appliance provided that it has been placed
or installed in its intended normal operating position and
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children aged from 3 years and less than 8 years shall not plug in, regulate
and clean the appliance or perform user maintenance.
WARNING!

READ THIS FIRST:
Check the pack and make sure you have all of the parts
listed on the front of this booklet. If not, contact the
supplier where you bought this product.
IMPORTANT SAFEGUARDS:
When using an electrical appliance, basic safety
precautions should always be observed, including the
following:
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Extreme caution is necessary where children or
persons with reduced physical, sensory or mental
capabilities may come into contact with the heater
when in use.
This heater is hot when in use. To avoid burns and
personal injury, do not let bare skin touch hot surfaces.
Never leave the heater unattended whilst it is in use.
The product is for household/oce use only.
WARNING - In order to avoid
overheating when in use, do
not cover the heater or position
where it may come in contact
with ammable materials, such as
curtains, drapes etc. to avoid the
risk of re.
WARNING - When scrapping the
heater, follow the regulations
concerning the disposal of oil.
This heater is lled with a precise quantity of special
oil. In case of leakage or repair which requires opening
of the oil container this should only be carried out by
the manufacturer or qualied engineer.
The heater must not be located adjacent to or against
an electrical socket.
Do not run the cord under carpets/rugs.
Arrange the cord away from high trac areas and
where it will not present a trip hazard.
Do not operate the heater with a damaged cord/plug
or if the heater malfunctions.
If the supply cord is damaged, it must be replaced by
qualied engineer.
Avoid the use of an extension cord as this may
overheat and cause a risk of re.
Use the heater in a well ventilated area.
Do not use the heater in any areas where petrol, paint
or other ammable liquids are stored e.g. garages or
workshops.
Do not use this heater in the immediate surroundings
of a bath, shower, swimming pool or where water is
present.
SPECIFICATION:
VOLTAGE: 220-240V ~ 50Hz
POWER MAX: 2kW
WARNING:
Only operate the heater in an upright position with
the feet attached, any other position could cause
malfunction.
When in use this product contains hot liquid.
Before each use the user must make a physical
inspection to ensure there is no damage to the metal
case of the product.
Do not try to repair the heater yourself, always consult
a suitably qualied engineer.
ASSEMBLY INSTRUCTIONS:
YOU MUST ATTACH THE FEET BEFORE OPERATING
THE HEATER.
1. Place the radiator upside-down on a scratch-free
location, making sure it is stable and will not fall.
2. To attach the castors to the mounting plate, unscrew
domed nut and feed through the holes in each end
of the mounting plate. Screw domed nut back in
place (g. 1) ensuring that they are fully tightened.
3. Unscrew wing nut from the U-shaped bolt (g. 2).
Hook U-shaped bolt onto the radiator between the
rst two ns (see g. 3).
4. Feed castor mounting plate on to the U-shaped bolt.
(g. 4).
5. Screw wing nut on to ends of U-shaped bolt and
fasten securely (g. 4). Over tightening may cause
damage to the radiator.
6. Now fasten second castor mounting plate between
last two ns (g. 5) and by repeating the above
steps.
TIMER INSTRUCTIONS & WARNINGS:
Heater should always be supervised when in use.
The heater will not operate if timer is set to the
position and the pins are not activated according to
the times required.
If the heater loses its electricity supply, e.g. switched
o at the mains socket or in the event of a power
failure, the time should be reset after the power is
re-established.
The red LED light will be illuminated when the timer is
set to ON position or the timing function is activated.
1. Regulate the timer according to the clock by turning
it clockwise (DO NOT TURN IT ANTI-CLOCKWISE).
(See Fig. 6 opposite).
2. The timer has a small switch with functions as
below:
1 = Unit is always on
= Timer function is on
3. Set the timer to position there are 96 small plastic
pins on the timer each correspond to 15 minutes
intervals. Push out the pins corresponding to the
time you want the heater to turn ON and push in the
pins corresponding to the time you want the heater
to turn OFF.
INSTRUCTIONS FOR USE:
WHEN IN USE
THIS PRODUCT
CONTAINS HOT
LIQUID.
BEFORE EACH USE THE USER
MUST MAKE A PHYSICAL
INSPECTION TO ENSURE THERE
IS NO DAMAGE TO THE METAL
CASE OF THE PRODUCT.
NOTE: When the heater is turned on for the rst time
or after having not been used for a long period, it may
smell for a short while.
1. Position the heater on a at and stable surface.
2. Set all controls to OFF and insert the plug into an
electrical socket.
3. Rotate the thermostat knob clockwise to MAX
position and switch the heater on as follows:
I = Low heat (800W)
II = Medium heat (1.2kW)
I + II = High heat (2kW)
4. When your room reaches the desired temperature,
slowly rotate the thermostat knob counter clockwise
until the red indicator light goes out. The thermostat
can now be left at this setting. As soon as the room
temperature has dropped below the set temperature,
the unit will switch itself on automatically until the set
temperature has been reached again. In this way the
room temperature remains constant with the most
economical use of electricity.
5. To change the room temperature setting, rotate the
thermostat knob clockwise to raise the temperature,
or anti-clockwise to lower it.
6. This heater includes an overheat protection system
that shuts o the heater when parts of the heater get
excessively hot.
7. This unit is tted with anti-tip cut-out protection.
Should the unit not be in the correct vertical position,
the heater will shut o.
8. To completely shut the heater o, turn all the controls
to OFF, and remove plug from the electrical socket.
Fig 1 Fig 2
Fig 3
Fig 4
Fig 5
Fig 6
WARNING!