EUCHNER MGB-L B-PN Series User manual

EN
Operating Instructions
Safety Systems
MGB-L..B-PN.-… (PROFINET)
With Data Structure Type A
From V3.30.0

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
2(translation of the original operating instructions) 2114575-06-02/21
Contents
1. About this document............................................................................................. 4
1.1. Scope............................................................................................................................................4
1.1.1. Notes on older product versions ......................................................................................4
1.2. Target group ..................................................................................................................................4
1.3. Key to symbols...............................................................................................................................4
1.4. Supplementary documents ..............................................................................................................4
2. Correct use .......................................................................................................... 5
3. Description of the safety function.......................................................................... 7
4. Exclusion of liability and warranty ......................................................................... 9
5. General safety precautions ................................................................................... 9
6. Function............................................................................................................. 10
6.1. Interlocking module MGB-L0.B-PN. .................................................................................................10
6.2. Locking module MGB-L1.B-PN. and MGB-L2.B-PN. ...........................................................................10
6.3. Guard locking for version MGB-L1 ..................................................................................................11
6.4. Guard locking for version MGB-L2 ..................................................................................................11
6.5. Control of guard locking ................................................................................................................12
6.5.1. Case A.........................................................................................................................12
6.5.2. Case B.........................................................................................................................13
6.5.3. Case C.........................................................................................................................14
7. System overview................................................................................................. 15
7.1. Bus module MGB-B-…-PN ..............................................................................................................15
7.2. Locking/release module MGB-L.-....................................................................................................16
7.3. Handle module MGB-H-…...............................................................................................................16
7.4. Escape release MGB-E-... (optional) ................................................................................................16
7.5. Dimension drawing .......................................................................................................................16
8. Manual release................................................................................................... 17
8.1. Auxiliary release............................................................................................................................17
8.2. Lockout mechanism......................................................................................................................18
8.3. Escape release (optional) ..............................................................................................................18
8.3.1. Preparing escape release ..............................................................................................19
9. Mounting............................................................................................................ 20
9.1. Mounting lens...............................................................................................................................21
10. Changing actuating direction .............................................................................. 22
11. Protection against environmental effects............................................................. 23
12. Controls and indicators....................................................................................... 24

3
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
13. Electrical connection .......................................................................................... 25
13.1. Notes about .........................................................................................................................25
13.2. Connections on the bus module .....................................................................................................26
13.2.1. Terminal assignment for version with push-pull plugs........................................................26
13.2.2. Terminal assignment for version with 7/8" and M12 plugs, d-coded ..................................26
14. Setup ................................................................................................................. 27
14.1. Integrating into PROFINET and PROFIsafe .......................................................................................27
14.2. Replacement of an MGB system without programming device ..........................................................27
14.3. Resetting system to factory settings ..............................................................................................27
14.4. Teach-in operation (only for MGB unicode).......................................................................................28
14.5. Mechanical function test................................................................................................................28
14.6. Electrical function test...................................................................................................................28
14.7. PROFINET data bytes (data blocks for non-safe functions)................................................................29
14.8. PROFIsafe data bytes (data block for safe functions)........................................................................30
15. MGB system diagnostic messages....................................................................... 31
16. PROFINET alarms ............................................................................................... 32
16.1. Fault in stacklight module ..............................................................................................................32
17. System status table ............................................................................................ 33
18. Technical data.................................................................................................... 34
18.1. Dimension drawings......................................................................................................................35
19. Troubleshooting and assistance........................................................................... 39
19.1. Latching fault when actuating the escape release............................................................................39
19.2. Resetting errors ...........................................................................................................................39
19.3. Troubleshooting help on the Internet...............................................................................................39
19.4. Mounting help on the Internet.........................................................................................................39
19.5. Application examples ....................................................................................................................39
20. Service .............................................................................................................. 40
21. Inspection and service ........................................................................................ 40
22. Declaration of conformity ................................................................................... 41

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
4(translation of the original operating instructions) 2114575-06-02/21
1. About this document
1.1. Scope
These operating instructions are valid for all MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A with the following
order numbers:
105283 109856 113230 113233 115621 121843
105284 109857 113231 114775 115622 121845
105287 110816 113232 114776 121841 121847
These operating instructions, the document Safety information and any enclosed data sheet form the complete user infor-
mation for your device.
Series Guard locking types System families Product versions
MGB
L0 (without guard locking)
…-PN…
from V3.30.1
L1 (guard locking by spring force) from V3.30.1
L2 (guard locking by solenoid force) from V3.30.0
1.1.1. Notes on older product versions
Products with lower product versions or without a version number are not described by these operating instructions. Please
contact our support team in this case.
1.2. Target group
Design engineers and installation planners for safety devices on machines, as well as setup and servicing staff possessing
special expertise in handling safety components.
1.3. Key to symbols
Symbol/depiction Meaning
Printed document
Internet
www Document is available for download at www.euchner.com
DANGER
WARNING
CAUTION
Safety precautions
Danger of death or severe injuries
Warning about possible injuries
Caution Slight injuries possible
NOTICE
Important!
Notice about possible device damage
Important information
Tip Useful information
1.4. Supplementary documents
The overall documentation for this device consists of the following documents:
Document title
(document number) Contents
Safety information
(2525460) Basic safety information
Operating instructions
(2114575) (this document)
Internet
www
Possibly enclosed data
sheet Item-specic information about deviations or additions
Important!
Always read all documents to gain a complete overview of safe installation, setup and use of the
device. The documents can be downloaded from www.euchner.com. For this purpose enter the doc.
no. in the search box.

5
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
2. Correct use
The following applies to MGB-L0:
The system comprises at least one interlocking module MGB-L0-... and one handle module MGB-H...
The safety system MGB is an interlocking device without guard locking (type 4). Devices with unicode evaluation possess a
high coding level, devices with multicode evaluation possess a low coding level.
In combination with a movable guard and the machine control, this safety component prevents dangerous machine functions
from occurring while the guard is open. A stop command is triggered if the guard is opened during the dangerous machine
function.
This means:
ÌStarting commands that cause a dangerous machine function must become active only when the guard is closed.
ÌOpening the guard triggers a stop command.
ÌClosing a guard must not cause automatic starting of a dangerous machine function. A separate start command must
be issued. For exceptions, refer to ENISO12100 or relevant C-standards.
The following applies to MGB-L1/MBG-L2:
The system comprises at least one locking module MGB-L1-…/MGB-L2-… and one handle module MGB-H…
The safety system MGB is an interlocking device with guard locking (type 4). Devices with unicode evaluation possess a
high coding level, devices with multicode evaluation possess a low coding level.
In combination with a movable guard and the machine control, this safety component prevents the guard from being opened
while a dangerous machine function is being performed.
This means:
ÌStarting commands that cause a dangerous machine function must become active only when the guard is closed and
locked.
ÌThe guard locking must not be released until the dangerous machine function has ended.
ÌClosing and locking a guard must not cause automatic starting of a dangerous machine function. A separate start com-
mand must be issued. For exceptions, refer to ENISO12100 or relevant C-standards.
For MGB-L0/MGB-L1/MGB-L2
The interlocking module MGB-L0B-PN.-… and the locking module MGB-L1B-PN.-…/MGB-L2B-PN.-… are operated as IO
devices in the PROFINET (PROFIsafe).
Before the device is used, a risk assessment must be performed on the machine, e.g. in accordance with the following
standards:
ÌENISO13849-1
ÌENISO12100
ÌIEC62061
Correct use includes observing the relevant requirements for installation and operation, particularly based on the following
standards:
ÌENISO13849-1
ÌENISO14119
ÌEN60204-1
The safety system MGB can be combined only with the intended modules in the MGB system family.
On the modication of system components, Euchner provides no warranty for function
The customer is responsible for the safe overall function, especially for the safe integration into the PROFIsafe environment.
Important!
ÌThe user is responsible for the proper integration of the device into a safe overall system. For this
purpose, the overall system must be validated, e.g. in accordance with ENISO13849-2.

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
6(translation of the original operating instructions) 2114575-06-02/21
Important!
ÌCorrect use requires observing the permissible operating parameters (see chapter 18. Technical
data on page 34).
ÌIf a product data sheet is included with the product, the information on the data sheet applies in
case of discrepancies with the operating instructions.
Table 1: Possible combinations for MGB components
Evaluation unit
Handle module
MGB-H-...
from V2.0.0
MGB…PN
From V3.30.0
Key to symbols Combination possible

7
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
3. Description of the safety function
Devices from this series feature the following safety functions:
The following applies in case of active guard lock monitoring (ÜK, bitSI 10):
Monitoring of guard locking and the position of the guard
(interlocking device with guard locking according to ENISO14119)
ÌSafety function (see chapter 6. Function on page 10):
- When guard locking is released, safety bit SI 10 (ÜK)=0 (monitoring of the locking element).
- When the guard is open, safety bit SI 9 (SK)=0.
- Guard locking can be activated only when the bolt tongue is located in the locking module (prevention of inadvertent
locking position (faulty closure protection)).
ÌSafety characteristics: category, Performance Level, PFHD(see chapter 18. Technical data on page 34).
Control of guard locking (safety bit SO 1)
ÌSafety function
If the device is used as guard locking for personnel protection, control of guard locking must be regarded as a safety
function.
The safety level of guard locking control is determined by the device PFHDint. and by the external control (e.g. PFHDext.
of the standstill monitor).
PFHdext. PFHdint.
(internal electronic)
Guardlocking Device
MGB-PN
(e.g. standstill
monitor)
Safetybit SO 1
(Guardlocking)
ÌSafety characteristics: category, Performance Level, PFHD(see chapter 18. Technical data on page 34).
The following applies in case of inactive guard lock monitoring (ÜK, bitSI 10):
Monitoring of the guard position
(interlocking device according to ENISO14119)
ÌSafety function: when the guard is open, safety bit SI 10 (SK)=0. (See chapter 6. Function on page 10.)
ÌSafety characteristics: category, Performance Level, PFHD(see chapter 18. Technical data on page 34).

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
8(translation of the original operating instructions) 2114575-06-02/21
The following applies to devices with emergency stop:
Emergency stop
(emergency stop device according to ENISO13850)
ÌSafety function: evaluation of emergency stop
ÌSafety characteristics: B10D value for the emergency stop and PFHDfor the evaluation electronics (see chapter 18.
Technical data on page 34)
PFHdext.
PFHdint.
(internal electronic,
evaluation of the
emergency stop)
MGB-PN
(Failsafe PLC)
B10d
(Emergency Stop)
Safetybit SI 1
(Emergency Stop)
The following applies to devices with connection for enabling switch:
Enabling function
ÌSafety function: evaluation of a connected enabling switch
ÌSafety characteristics: B10D value for the enabling switch (see manufacturer’s information) and PFHDfor the evaluation
electronics (see chapter 18. Technical data on page 34)
PFHdext.
PFHdint.
(internal electronic,
evaluation of the
enabling switch)
MGB-PN
(Failsafe PLC)
B10d
(Enabling Switch)
Safetybit SI 2
(Enabling Switch)
For devices with multi-position switch:
Detection of the switch position
ÌSafety function: evaluation of the switch position, e.g. for safe switchover between individual operating modes
ÌSafety characteristics: PFHDfor the evaluation electronics (see chapter 18. Technical data on page 34). The switch
position is scanned electronically. There is therefore no B10D value for the switch.
PFHdext.
PFHdint.
(internal electronic,
evaluation of the
selector switch)
MGB-PN
(Failsafe PLC)
Safetybits
SI 6, SI 7, SI 8
(Selector Switch)

9
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
4. Exclusion of liability and warranty
In case of failure to comply with the conditions for correct use stated above, or if the safety regulations are not followed,
or if any servicing is not performed as required, liability will be excluded and the warranty void.
5. General safety precautions
Safety switches fulll personnel protection functions. Incorrect installation or tampering can lead to fatal injuries to personnel.
Check the safe function of the safeguard particularly
Ìafter any setup work
Ìafter the replacement of an MGB component
Ìafter an extended period without use
Ìafter every fault
Ìafter any change to the DIP switch settings
Independent of these checks, the safe function of the safeguard should be checked at suitable intervals as part of the
maintenance schedule.
WARNING
Danger to life due to improper installation or due to bypassing (tampering). Safety components perform
a personnel protection function.
ÌSafety components must not be bypassed, turned away, removed or otherwise rendered ineffec-
tive. On this topic pay attention in particular to the measures for reducing the possibility of bypass-
ing according to ENISO14119:2013, section 7.
ÌThe switching operation is allowed to be triggered only by the intended handle module MGB-H…
that is positively fastened to the guard.
ÌPrevent bypassing by means of replacement actuators (only for multicode evaluation). For this
purpose, restrict access to actuators and to keys for releases, for example.
ÌMounting, electrical connection and setup only by authorized personnel possessing the following
knowledge:
- specialist knowledge in handling safety components
- knowledge about the applicable EMC regulations
- knowledge about the applicable regulations on operational safety and accident prevention.
Important!
Prior to use, read the operating instructions and keep these in a safe place. Ensure the operating
instructions are always available during mounting, setup and servicing. For this reason you should
archive a printed copy of the operating instructions. You can download the operating instructions from
www.euchner.com.

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
10 (translation of the original operating instructions) 2114575-06-02/21
6. Function
6.1. Interlocking module MGB-L0.B-PN.
Together with a handle module, the interlocking module makes it possible to interlock movable guards. The combination
also serves as a mechanical door stop at the same time.
The following switch-on condition applies to safety bit SI 9 (SK):
ÌGuard closed (T)
ÌBolt tongue inserted into interlocking module (R)
See also chapter 17. System status table on page 33 and chapter 14.8. PROFIsafe data bytes (data block for safe
functions) on page 30.
The interlocking module detects the position of the guard and the position of the bolt tongue.
The bolt tongue in the handle module is moved into and out of the interlocking module by actuating the door handle.
6.2. Locking module MGB-L1.B-PN. and MGB-L2.B-PN.
Together with a handle module, the locking module makes it possible to lock movable guards. The combination also serves
as a mechanical door stop at the same time.
Important!
To operate the device as guard locking for personnel protection according to ENISO14119, the
signals for door position (T=PROFIsafe bit SI 3), bolt position (R= PROFIsafe bit SI 4) and guard
lock monitoring (Z= PROFIsafe bit SI 5) must be polled in a logical AND operator. This operator is
already implemented in the PROFIsafe data block (ÜK= safety bit SI 10).
As an alternative, you can also link the bits SI 3 to SI 5 individually in your control system.
The following switch-on condition applies to safety bit SI 10 (ÜK):
ÌGuard closed (T)
ÌBolt tongue inserted into locking module (R)
ÌLocking arm in locking position (guard lock monitoring) (Z)
See also chapter 17. System status table on page 33 and chapter 14.8. PROFIsafe data bytes (data block for safe
functions) on page 30.
The locking module detects the position of the guard and the position of the bolt tongue. The position of the locking arm
is also monitored.
The bolt tongue in the handle module is moved into and out of the locking module by actuating the door handle.
When the bolt tongue is fully inserted into the locking module, the locking arm locks the bolt tongue in this position. Depending
on version, this locking is by spring force or solenoid force.

11
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
6.3. Guard locking for version MGB-L1
(guard locking actuated by spring force and released by power-ON)
Activating guard locking: close guard, no voltage at the solenoid (safety bit SO 1=0).
Releasing guard locking: apply voltage to the solenoid (safety bit SO 1=1).
The spring-operated guard locking functions in accordance with the closed-circuit current principle. If the voltage is interrupted
at the solenoid, the guard locking remains active and the guard cannot be opened directly.
Important!
If the guard is open when the power supply is interrupted and is then closed, guard locking is activated.
This can lead to persons being locked in unintentionally.
As long as the locking arm is closed, the bolt tongue cannot be pulled out of the locking module and the guard is locked.
When voltage is applied to the guard locking solenoid, the locking arm is opened and bolt tongue is released. The guard
can be opened.
6.4. Guard locking for version MGB-L2
(guard locking actuated by power-ON and released by spring force)
Important!
Use as guard locking for personnel protection is possible only in special cases, after strict assessment
of the accident risk (see ENISO14119:2013, section 5.7.1)!
Activating guard locking: apply voltage to the solenoid (safety bit SO 1=1).
Releasing guard locking: disconnect voltage from the solenoid (safety bit SO 1=0).
The magnetically actuated guard locking operates in accordance with the open-circuit current principle. If the voltage is
interrupted at the solenoid, the guard locking is released and the guard can be opened directly!
The guard can be opened as long as no voltage is applied to the guard locking solenoid.
When voltage is applied to the guard locking solenoid, the locking arm is held in the locked position and the guard is locked.

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
12 (translation of the original operating instructions) 2114575-06-02/21
6.5. Control of guard locking
From MGB version V2.36.4, the factory setting ensures that control is possible only from the safe control area.
By changing the parameters in the conguration tool of your control system, it can be set whether bit O 16 (in the safe
data block for the MGB locking module) is evaluated as well.
Important!
The following applies to MGB-L2:
Control of the guard locking via the safe control area does not provide increased safety, as the de-
vice-internal control of the guard locking is only of single-channel design.
Important!
The following functions depend on the MGB version, the version of the GSD le and the settings made
there.
Compare the specied versions with those on your device and in your GSD le. The version number
of your MGB can be found on the type label (format: VX.XX.X).
MGB version GSD version Continue in section ...
up to and including V2.35.4 ..._110026-20110725 Case A
..._110026-20110815 Case A
From V3.30.0 ..._110026-20110725 Case B
..._110026-20110815 or newer Case C
6.5.1. Case A
You have an MGB with a version number of V2.35.4 and a GSD le with a version number of ..._110026-20110725 or older.
Or you have an MGB with a version number of V2.35.4 and a GSD le with a version number from ..._110026-20110815.
The guard locking solenoid is controlled if
Ìbit O 16 OR bit SO 1 = 1
Truth table
PROFINET bit PROFIsafe bit Guard locking with
O 16 SO 1 MGB-L1... MGB-L2...
0 0 Active Inactive
0 1 Inactive Active
1 0 Inactive Active
1 1 Inactive Active
What must be observed?
Guard locking can be controlled from the non-safe control area. The combination with the more up-to-date GSD le allows
a parameter to specify which bits are to be used for control. However, the device does not support this function. In other
words, the setting in your conguration software remains ineffective.

13
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
6.5.2. Case B
You have an MGB with a version number of V3.30.0 and a GSD le with a version number of ..._110026-20110725 or older.
The guard locking solenoid is controlled if
for MGB-L1...
Ìbit SO 1 = 1
for MGB-L2...
Ìbit O 16 OR bit SO 1 = 1
Truth table
PROFINET bit PROFIsafe bit Guard locking with
O 16 SO 1 MGB-L1... MGB-L2...
0 0 Active Inactive
0 1 Inactive Active
1 0 Active Active
1 1 Inactive Active
What must be observed?
Bit O 16 does not have any function with version MGB-L1.... In existing installations in which old devices are replaced with
new ones (e.g. due to defect), malfunctions can occur if control via bit O 16 was programmed in the PLC.
Remedy:
1. Replace the old GSD le with a version from ..._110026-20110815.
2. In the parameter Locking module – solenoid control, activate non-safe control of the guard locking solenoid via bit O 16.
3. Set bit SO 1 permanently to the value 1.
¨The guard locking solenoid is controlled exclusively via bit O 16
or
ÌChange the control bit from O 16 to SO 1 in your PLC program.

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
14 (translation of the original operating instructions) 2114575-06-02/21
6.5.3. Case C
You have an MGB with a version number of V3.30.0 and a GSD le with a version number from ..._110026-20110815.
The guard locking solenoid is controlled if:
Ìbit SO 1 = 1 (factory setting)
Truth table
PROFINET bit PROFIsafe bit Guard locking with
O 16
Not relevant
SO 1 MGB-L1... MGB-L2...
00Active Inactive
01Inactive Active
10Active Inactive
11Inactive Active
What must be observed?
You can dene in the GSD le whether bit O 16 may be used for control in addition to bitSO 1. The setting is specied in
the parameter Locking module - solenoid control.
If O 16 is additionally used, the guard locking solenoid is controlled if
for MGB-L1...
Ìbit SO 1 AND bit O 16 = 1
for MGB-L2...
Ìbit SO 1 OR bit O 16 = 1
Truth table
PROFINET bit PROFIsafe bit Guard locking with
O 16 SO 1 MGB-L1... MGB-L2...
0 0 Active Inactive
0 1 Active Active
1 0 Active Active
1 1 Inactive Active

15
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
7. System overview
Mounting plate
Escape release (optional)
(MGB-E...)
Handle module
(MGB-H...)
Locking/release module
(MGB-L...)
Bus module
(Pronet)
(MGB-B...)
Figure 1: Components at a glance
NOTICE
MGB-PN systems are completely factory congured. The conguration must not be changed subse-
quently. The illustrations in this chapter can deviate from your system and serve only as examples. The
conguration of your MGB system can be found in the data sheet included with every MGB system.
7.1. Bus module MGB-B-…-PN
Key:
1LED indicator
2Power supply
3PROFINET connection
Notice:
Depending on version, additional controls and indicators may be integrated into the
cover. See enclosed data sheet.
1
23
Figure 2: Bus module MGB-B-…-PN (conguration example)

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
16 (translation of the original operating instructions) 2114575-06-02/21
7.2. Locking/release module MGB-L.-
2
1
3
4
Key:
1LED indicator
2Cover for auxiliary release
3Locking arm (only version with guard locking)
4Auxiliary marking for max. permitted mounting distance
Notice:
Depending on version, additional controls and indicators may be integrated into the
cover. See enclosed data sheet.
Figure 3: Locking/release module MGB-L.-
7.3. Handle module MGB-H-…
1
2
33
4
Key:
1Door handle
2Locking screws T10 for housing cover and handle adjustment
3Fold-out lockout mechanism
(optional: second, automatically extending lockout mechanism)
4Bolt tongue
Notice:
Depending on version, a mounting plate can be included.
See enclosed data sheet.
Figure 4: Handle module MGB-H-…
7.4. Escape release MGB-E-... (optional)
1 2 3 4
Key:
1Door handle
2Housing
3Actuation axis 8 x 8 mm
(different lengths available)
4Protective sleeve
Notice:
Depending on version, a mounting plate can be included.
See enclosed data sheet.
Figure 5: Escape release MGB-E-...
7.5. Dimension drawing
See enclosed data sheet.

17
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
8. Manual release
Some situations require the guard locking to be released manually (e.g. malfunctions or an emergency). A function test
should be performed after release.
More information on this topic can be found in the standard ENISO14119:2013, section 5.7.5.1. The device can feature
the following release functions:
8.1. Auxiliary release
In the event of servicing, the guard locking can be released with the auxiliary release irrespective of the state of the solenoid
(see Figure 6).
Important!
ÌThe system enters into a latching fault when the auxiliary release is actuated. See System status
table, signal sequence incorrect status (DIA red, Lock ashes 1 time).
ÌThe system might not enter into a latching fault if the auxiliary release is actuated very slowly.
ÌThe auxiliary release is not a safety function.
ÌThe machine manufacturer must select and use a suitable release (escape release, emergency
release, etc.) for a specic application. A hazard assessment is required for this purpose. It may
be necessary to take specications from a product standard into account.
ÌThe correct function must be checked at regular intervals.
ÌLoss of the release function due to mounting errors or damage during mounting. Check the re-
lease function every time after mounting.
ÌObserve the notes on any enclosed data sheets.
The locking screw must be screwed back in and sealed (with sealing lacquer, for example) after mounting and after every
use of the auxiliary release. Tightening torque 0.5 Nm.
1. Undo locking screw.
2. Lift locking arm using a screwdriver and actuate door handle.
Figure 6: Auxiliary release

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
18 (translation of the original operating instructions) 2114575-06-02/21
8.2. Lockout mechanism
If the lockout mechanism is pivoted out/extended, the bolt tongue cannot be extended. The lockout mechanism can be
secured with padlocks (see Figure 7). This is intended to prevent people from being locked in unintentionally. The lockout
mechanism does not fulll any safety function.
¨To pivot out, press the grooved part (possible only with bolt tongue retracted).
12Key:
1Padlock ∅min. 2mm,
∅max. 10 mm
2Automatically extending, second lockout mechanism
Padlock ∅min. 6mm, ∅max. 10 mm
Notice:
You can t a maximum of 3 locks Ø 8mm.
Figure 7: Lockout mechanism secured with padlock
8.3. Escape release (optional)
The escape release is used to open a locked guard from the inside without tools.
The system enters into a latching fault when the escape release is actuated.
See chapter 17. System status table on page 33, signal sequence incorrect status (DIA red, Lock ashes 1 time).
The system might not enter into a latching fault if the escape release is actuated very slowly.
Important!
ÌIt must be possible to actuate the escape release manually from inside the protected area without
tools.
ÌIt must not be possible to reach the escape release from the outside.
ÌThe actuator must not be under tensile stress during manual release.
ÌThe escape release meets the requirements of Category B according to ENISO13849-1:2008.
ÌThe correct function must be checked at regular intervals.
ÌObserve the notes on any enclosed data sheets.
ÌFit escape release such that operation, inspection and service are possible.
ÌThe actuation axis for the escape release must be inserted min. 10 mm into the handle module. Note the information on
the different prole widths in the chapter 8.3.1. Preparing escape release on page 19.
ÌAdjust escape release axis at right angles to the handle module. See Figure 8.

19
2114575-06-02/21 (translation of the original operating instructions)
Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
EN
8.3.1. Preparing escape release
Prole width Length required for actuation
axis Which EUCHNERparts are required? Necessary work steps
Without
mounting
plates
With mounting
plates
(4 mm each)
D D+9 D+17
30 mm 39 mm 47 mm Standard escape release
with 107 mm axis
(order no. 100465)
Shorten to required length
40 mm 49 mm 57 mm Standard escape release
with 107 mm axis
(order no. 100465)
If necessary,
extended actuation axis (order no. 106761)
Without mounting plates:
none
With mounting plates:
Use extended actuation axis and protective sleeve and
shorten to required length
45 mm 54 mm 62 mm Standard escape release
with 107 mm axis
(order no. 100465)
and
extended actuation axis (order no. 106761)
Use extended actuation axis and protective sleeve and
shorten to required length
50 mm 59 mm 67 mm Standard escape release
with 107 mm axis
(order no. 100465)
and
extended actuation axis (order no. 106761)
Use extended actuation axis and protective sleeve and
shorten to required length
55,5
M4
250
182
D + 9
D -1
D
(11,5) 55,5
Example without mounting plates:
Escape release
Handle module
Actuation axis Protective sleeve
(+4 mm per mounting plate)
(+4 mm per mounting plate)
1Insert actuation axis. The snap ring Amust be in contact with the escape release B.
2Fit door handle.
3Tighten xing screw to 2Nm and push in cap.
4Fit protective sleeve.
1
3
2
4
A
B
Figure 8: Preparing escape release

Operating Instructions Safety Systems
MGB-L..B-PN.-… (PROFINET) and With Data Structure Type A
20 (translation of the original operating instructions) 2114575-06-02/21
9. Mounting
WARNING
Mounting must be performed only by authorized personnel.
With two-leaf hinged doors, one of the two door leaves must also be latched mechanically.
Use a rod latch (Item) or a double-door lock (Bosch Rexroth) for this purpose, for example.
Important!
ÌIn case of ush installation, the operating distances change as a function of the installation depth
and the guard material.
Locking module Handle module
Locking module Handle module
Surface mounting
Flush installation
Actuating range
Actuating range
Tip!
ÌYou will nd an animation on the mounting process at www.mgb.euchner.com.
ÌThe color and labeling of pushbuttons and indicators can be modied.
For mounting steps, see Figure 9 and Figure 10 to Figure 15.
Attach system such that operation of the auxiliary release as well as inspection and service are possible.
The locking screw of the auxiliary release must be returned to its original position and sealed before putting into operation
(with sealing lacquer, for example).