Event Lighting PS300IICW User manual

LED Fresnel
PS300IICW PS300IIWW
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to
change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting
for any clarification or information regarding this item.
www.event-lighting.com.au Ver 1.8.0

www.event-lighting.com.au
1
CONTENTS
Safety Instructions
- Power Input & Power Linking
- Product installation
Product Installation
- Fuse replacement
Product appearance
- Lux Chart
- Dimensions
Control Board Operation
- DMX Addressing
- DMX Modes
- Dimmer Curves
- Static Settings
DMX Values
Technical Specifications
Warranty

www.event-lighting.com.au
2
Safety Instructions
WARNING
•Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
•Do not look at the light source when the device is on.
•CAUTION: This unit's housing may be hot during and after operation.
•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
•Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
•Use a safety chain when mounting this device overhead.
•Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
•Do not operate this device if the housing, lenses, or cables appear damaged.
•Do not connect this device to a dimmer or rheostat.
•ONLY connect this device to a grounded and protected circuit.
•ONLY use the hanging bracket to carry this device.
•In case of a serious operating problem, stop using immediately.
•The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.

www.event-lighting.com.au
3
Dimensions –PS300IICW
Lux Chart –PS300IICW

www.event-lighting.com.au
4
Dimensions –PS300IIWW
Lux Chart –PS300IIWW

www.event-lighting.com.au
5
CONTROL BOARD OPERATION
Press the Menu until one of the following had been displayed:
Function
Values
Description
DMX
001 –512
Set DMX Address.
CHAN
01CH, 02CH, 03CH
Set DMX Channel Mode.
MANUAL
DIM: 000 - 255
D_F: 000 - 255
STO: 000 - 255
Manually set intensity of Dimmer (0 = off, 255 = brightest).
Manually set intensity of Dimmer Fine (0 = off, 255 = brightest).
Manually set speed of Strobe (0 = off, 255 = fastest).
CURVE
Linear, S, Log
Select the dimming curve between Linear, S and Log.
RESET
NO, Yes
Reset all settings to factory default.
TEMP
Cur: NNN
Displays the current temperature in degrees Celsius.
FAN
NNN –Speed
Auto / Silent
Displays the current fan speed.
Select between Auto and Silent fan modes.
VERSION
A1.8.0
Displays the current firmware version.
Use “Up” and “Down” buttons to select your desired operation, then press “Enter”.

www.event-lighting.com.au
6
DMX VALUES
1 channel mode
Channel
Value
Function
1
000-255
Dimmer Coarse
2 channels mode
Channel
Value
Function
1
000-255
Dimmer Coarse
2
000-255
Dimmer Fine
3 channels mode
Channel
Value
Function
1
000-255
Dimmer Coarse
2
000-255
Dimmer Fine
3
000-255
Strobe

www.event-lighting.com.au
7
TECHNICAL SPECIFICATIONS
Model
PS300IICW
PS300IIWW
Dimensions and Weight
Overall size LxWxH
668 X 320 X 463 mm
Weight (kg)
12
Power
Power Supply
100~240V AC, 50/60 Hz
Power
Consumption (w)
300
Fuse
T 1 A, 250 V
Details
LED
300W COB
LED lifespan
50 000hrs
Colour Temperature
5600K
3200K
Operation Modes
DMX, static control
Beam Angle
19°, 26° or 36°
Dimming
8-bit or 16 bit –0-100%
Strobe rate
1-25 Hz
Lens
Optional: PS19IILENS, PS36IILENS
Refresh Rate
8000Hz
DMX Channel mode
1 / 2 / 3
Power Input
Seetronic® True1
Power Output
Seetronic® True1
DMX connector
3 pin male XLR and 3 pin female XLR, 5 pin male and 5 pin female XLR
Construction
Matte Black finish aluminium
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.