Event Lighting PAR12X12L User manual

PAR12X12L
12x 12W RGBWAU 6-in-1 LED PAR
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.

www.event-lighting.com.au
1
Version 1.0
Safety Instructions
Warning
• Do not open this device, there are no user serviceable parts inside. Risk of electric
shock.
• Do not look directly at the light source from close range.
• Avoid contact with the unit during operation, as the housing may become hot. Allow the
fixture to cool for at least 15 minutes after turning off before touching.
• Install this device in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
• Do not operate this device, or connect this device to power, within 50cm of any
flammable material.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors where excessive dust, heat, water, or humidity may
affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• Do not operate this device at temperatures higher than 40°C (104°F).
• Only connect this device to a grounded and protected circuit.
• Only use the hanging bracket to carry this device.
• Stop using this device immediately if a serious operating problem becomes apparent.
Product Installation
PAR12X12L can be mounted in many orientations, provided each individual device is secured by
the use of the correct mounting bracket. Use a safety chain when mounting PAR12X12L
overhead.

www.event-lighting.com.au
2
Dimensions
Lux Chart
Distance (m)
1
2
3
4
5
Diameter (m)
Ø 0.73
Ø1.46
Ø2.18
Ø2.91
Ø 3.64
Red
1445
409
180
93
70
Green
2030
570
250
130
95
Blue
2910
882
270
199
143
White
2420
734
322
171
126
Amber
850
258
117
61
46
UV
840
264
120
66
49
Full
8550
2580
1123
543
423

www.event-lighting.com.au
3
Control Board Operation
Menu Map
->
-
Select DMX address
->
or
Select DMX channel mode (CH-1: 6ch /
CH-2: 11ch)
->
-
Set program speed
->
-
Select built-in program
->
Select sound active mode
->
-
Select static colour mode
(See static colour mode chart below)
->
-
Set strobe speed (Hz)
->
-
Set red colour intensity
->
-
Set green colour intensity
->
-
Set blue colour intensity
->
-
Set white colour intensity
->
-
Set amber colour intensity
->
-
Set UV colour intensity
->
-
Set dimmer speed
(nod0: fastest / nod4: slowest)
->
or
Toggle LED display on / off
->
Long press “Enter” button to show current temperature
->
Show current software version
->
or
Restore settings to factory default

www.event-lighting.com.au
4
Static Colour Mode
Value
Function
C1
Red
C2
Green
C3
Red+Green
C4
Blue
C5
Blue+Red+UV
C6
Green+Blue
C7
Red +Green+Blue+Amber+UV
C8
White
C9
Red+White
C10
Green+White
C11
Red+Amber
C12
Blue+White+UV
C13
Red + Blue+White+UV
C14
Red + Blue+White
C15
Red+Green+Blue+White+Amber+UV
DMX Chart
6 Channel Mode
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
5
000-255
Amber: 0% ~ 100%
6
000-255
UV: 0% ~ 100%

www.event-lighting.com.au
5
11 Channel Mode
Channel
Value
Function
Note
1
000-255
Master DIMMER 0% ~ 100%
2
000-255
Red: 0% ~ 100%
3
000-255
Green: 0% ~ 100%
4
000-255
Blue: 0% ~ 100%
5
000-255
White: 0% ~ 100%
6
000-255
Amber: 0% ~ 100%
7
000-255
UV: 0% ~ 100%
8
000-012
Strobe OFF
013-255
Strobe (slow-fast)
9
000-009
No Function
010-019
Program 1
020-029
Program 2
030-039
Program 3
040-049
Program 4
050-059
Program 5
060-069
Program 6
070-079
Program 7
080-089
Program 8
090-099
Program 9
100-109
Program 10
110-119
Program 11
120-129
Program 12
130-139
Program 13
140-255
Sound active mode
10
000-255
Speed of auto programs (slow
~ fast)
Ch9 must be set between
10-139
11
000-255
Colour fade time (jump ~ fade)
Mode must be set to “nod0”

www.event-lighting.com.au
6
IR Remote
In order to use the IR Remote, PAR12X12L must be in DMX mode
without an active DMX connection. If a DMX signal is received,
PAR12X12L will prioritise the DMX signal and ignore the IR Remote.
Use On/Off to turn PAR12X12L on or off. The current IR settings will be
saved automatically when PAR12X12L is powered off and reloaded when
it is turned on again. To reset to the factory default Blackout mode, long
press Off.
Press R/G/B/W/A/U to light up the LEDs in red, green, blue, white, amber
or UV respectively. Press a number 0-9 in the orange shaded area to
select a pre-set colour.
Press + to increase the intensity of the selected colour and - to decrease
the intensity of the selected colour.
Press Auto/Sound/Strobe to switch on or off Auto mode, Sound Active mode and Strobe mode,
respectively.
Press Blackout to clear all the remote settings and blackout PAR12X12L.

www.event-lighting.com.au
7
Technical Specifications
Power
• Input Voltage: 100~240V AC, 50/60 Hz.
• Power Consumption: 60W
• Connection: IEC in/out.
Photometrics
• Light Source: 12x 12W RGBWAU LEDs.
• Beam Angle: 40°.
• PWM: 20,000 Hz.
• LED Lifespan: 50,000 hours.
Effects
• Dimming: 0-100%.
• Strobe: 1-20Hz.
Control
• Protocol: DMX512 (Optional Wireless DMX).
• DMX Channels: 6 / 11.
• Interface: 3-pin XLR in/out.
• Built-in Programming: Yes
• Display: 4-button and 4-digit LED Display Control Panel
• Cooling: Fanless
Housing
• Materials: Die Cast Aluminium.
• Finishing: Matte Black.
• IP Rating: IP20
• Net Weight: 1.85kg
• Overall Size: 212x220x62mm
Warranty
Please refer to your local dealer or contact Event Lighting.