Event Lighting PRO PAR User manual

PRO PAR
Model No. PAR4X12B
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
Ver 1.0.1 (27 Apr 2020)

www.event-lighting.com.au
1
CONTENTS
Safety Instructions
Product Installation
Diagrams
Control Board Operation
DMX chart
Technical specifications
Warranty

www.event-lighting.com.au
2
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.

www.event-lighting.com.au
3
Lux Chart
Dimensions

www.event-lighting.com.au
4
CONTROL BOARD OPERATION
Menu Map
->
-
Select DMX address for 6 ch mode
->
-
Select DMX address for 10 ch mode
->
-
Remaining percentage of battery power
->
or
Set dimming speed (SL: slow / FA: fast)
->
or
When lost DMX signal,
ho: keep the last DMX signal state
OF: blackout
->
or
Switch on/off wireless DMX control
->
or
Switch on/off IR remote control
->
-
Set red colour intensity
->
-
Set green colour intensity
->
-
Set blue colour intensity
->
-
Set white colour intensity
->
-
Set amber colour intensity
->
-
Set UV colour intensity
->
-
Display IR control brightness level
->
-
Set strobe speed
->
-
Select 15 static colour modes, see chart: Static
colour mode
->
-
Select 16 speed of auto colour switch mode
->
-
Select 16 speed of auto colour fading mode
->
-
Select 16 speed of auto colour pulse out mode
->
-
Select sound active mode with different sound
sensitive level

www.event-lighting.com.au
5
Wi-Fi Control Mode
Display current temperature
Display version number
->
or
Reset
Static colour mode
Value:
Function:
C1
R
C2
G
C3
R + G
C4
B
C5
B + R + UV
C6
G + B
C7
R + G + B + A + UV
C8
W
C9
R + W
C10
G + W
C11
R + A
C12
B + W + UV
C13
R + B + W + UV
C14
G + B + W
C15
R + G + B + W + A + UV
Wireless DMX mode
Set up wireless DMX
The fixture needs to be paired from the wireless DMX transmitter. Follow below steps to pair.
Step 1: Connect the DMX512 controller to the wireless DMX transmitter.
Step 2: Switch on the PAR6x12OB, turn on the wireless DMX control on from control panel ‘rfon’
Step 3: Set the PAR6x12OB to DMX mode. (AXXX or dXXX)
Step 4: Switch off the PAR6x12OB. Press and hold the ‘DMX select’ button whilst switching on the fixture. Once the
fixture turns on the ‘wireless status’ light will be lit white and the unit will be in ‘setup mode’.
Step 5: The ‘wireless indicator’ will be lit to a specific colour to indicate the protocol being used for the transmission as
shown in TABLE1. Pressing the button will cycle through the colours and once you want to set the protocol pressing the
button for more than 1s will save the protocol. The transmitters, receivers and transceivers will remember the protocol
used even after a power cycle with their built in memory chip.
Now you need to setup as for WDMX mode or EL mode

www.event-lighting.com.au
6
Protocols TABLE1
Colour
Protocol
Red
ELDMX Transmit and receive
Green
W-DMX Receive
Blue
W-DMX G3 Transmit
Using W-DMX mode
Transmitters
Pressing the button momentarily will connect to all unconnected receivers in the coverage area.
Pressing the button for more than 3s will disconnect all receivers in the coverage area.
Receivers
Pressing the button for more than 3s will disconnect the device with a transmitter.
NOTE:
The colour of the light will indicate the group as shown in Table2.
The receiver will not connect with a new transmitter unless it is disconnected first.
W-DMX Status Indicators TABLE2
Protocol
Action
Description
W-DMX Receive
White
No connection
Red
Deleting Connection
Red Fast Flash
Connection Lost
Green Fast Flash
Connecting to Transmitter
Green Slow Flash
Connected but no DMX signal
Green
Connected with DMX signal
W-DMX Transmit
Red
Deleting All Receivers
Blue Fast Flash
Connecting with the receivers
Blue Slow Flash
No DMX input
Blue
Transmitting DMX
Using EL wireless DMX mode
Changing Channel Group
Pressing the Button will show you the current channel group being used and pressing it again will cycle through the
groups. The colour of the light will indicate the group as shown in Table3.
Status Indicators TABLE3
Protocol
Action
Description
ELDMX
Solid Colour (Red, Green, Blue,
Yellow, Cyan, Magenta)
1 of the 6 colour groups
Flashing Red
Transmitting DMX
Flashing Green
Receiving DMX

www.event-lighting.com.au
7
IR remote control mode
-You must switch off wireless DMX function, select .
-Select , then use IR remote to switch on IR remote control mode.
Key
Function
Display
Switch on/off IR function
to
or your last setting
Pressing <blackout> button to switch on
the fixture IR function, fixture will go to
CC12 auto colour switch mode or your
last setting
Pressing <blackout> button when unit
under IR mode, fixture will blackout and
on IR standby mode
Select auto colour switch mode (CC)
or auto colour pulse out mode (CP)
with different speed
between
Using <Auto> button to select CC or CP
mode, using to change speed.
Select sound active mode (SU) with
different sensitivity level
Pressing <SOUND> button to select SU
mode, using to change
sensitivity level
Select auto colour fade mode (dE)
with different speed
Pressing <FADE> button to select dE
mode, using to change speed.
Select manual colour mode
to
Pressing <MANUAL> button to entry
manual colour mode
Using
button to cycle though 20% change of
intensity of each colour separately.
to
Pressing <MANUAL> button to quit
manual colour mode, fixture will blackout
Select intensity of LED full on mode
to
Pressing <%> button to cycle though
10% change of intensity on static colour
(R255+G255+B255+W255+A255+U255)
mode.
Select intensity of static colour
(R255+G255+B255+W255+A255+U
255)
to
Using to change intensity

www.event-lighting.com.au
8
Select intensity of static colour
(R255)
to
Using to change intensity
Select intensity of static colour
(UV50+R255)
to
Using to change intensity
Select intensity of static colour
(R255+G50)
to
Using to change intensity
Select intensity of static colour
(G255)
to
Using to change intensity
Select intensity of static colour
(G160+B255+UV100)
to
Using to change intensity
Select intensity of static colour
(B255+UV50)
to
Using to change intensity
Select intensity of static colour
(R50+B255+UV200)
to
Using to change intensity
Select intensity of static colour
(R255+B150+UV255)
to
Using to change intensity
Select intensity of static colour
(R255+B20+A200)
to
Using to change intensity
Reset factory default setting
to
No function
Add strobe effect on CC, CP, SU, dE,
dl and static colour mode.
No change
Pressing <STROBE> button to cycle
though 1/8 change of strobe speed

www.event-lighting.com.au
9
Wi-Fi Mode
Downloading the application
Login to the App Store (iOS) or Google Play (Android), download LED Wifi application. It allows you to control the
PAR4x12B using your mobile devices with iOS / Android operating systems.
App Store (iOS) Google Play (Android)
Connecting mobile devices with iOS / Android to PAR4X12B
Step 1: On your mobile devices, select Settings > Wi-Fi > list of available Wi-Fi device will be shown.
Step 2: Select ‘LED_***’ and connect.
PAR4X12B has own 3-digit Wi-Fi ID and display as LED_***). “***” is based on the last three digits of the serial number,
which is printed on the back of the machine. Select light and connect it.
Step 3: Open LED Wifi application to control the light in 3 different modes.

www.event-lighting.com.au
10
DMX Chart
6 channels Mode
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
5
000-255
Amber: 0% ~ 100%
6
000-255
UV: 0% ~ 100%
10 channels Mode
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
5
000-255
Amber: 0% ~ 100%
6
000-255
UV: 0% ~ 100%
7
000-255
Master Dimmer 0% ~ 100%
8
000-255
Strobe (slow-fast)
9
000-050
No function
051-100
Select 15 Static colour mode (CL), colour have been controlled by ch10
101-150
Select Auto colour switching modes (CC), program speed have been
controlled by ch10
151-200
Select Auto colour fade mode (dE), program speed have been controlled
by ch10
201-250
Select Auto colour pulse mode (CP), program speed have been
controlled by ch10
251-255
Select Sound active mode (SU), sound sensitivity level have been
controlled by ch10
10
(Ch9 set 051-100)
000-015
No function
016-031
R
032-047
G
048-063
R + G
064-079
B
080-095
B + R + UV
096-111
G + B
112-127
R + G + B + A + UV
128-143
W
144-159
R + W
160-175
G + W
176-191
R + A
192-207
B + W + UV
208-223
R + B + W + UV

www.event-lighting.com.au
11
224-239
G + B + W
240-255
R + G + B + W + A + UV
10
(Ch9 set 101-250)
000-255
Select auto run speed for (CC, dE and CP) from slow to fast
10
(Ch9 set 251-255)
000-255
Select sound sensitivity level for sound active mode (SU) form low to high
TECHNICAL SPECIFICATIONS
Power
Input Voltage: 100~240V AC, 50/60 Hz
Power Pack: 16.8V DC 2A
Power Consumption: 48W
Connection: DC Input Socket
Photometric
Light Source: 4pcs 6-in-1 RGBWAU 12W LED
Beam Angle: 40°
Output: 3100 lux on @1M RGBWAU Full on
PWM: 20,000 Hz
LED Lifespan: 50,000 hours
Effects
Dimming: 0~100%
Strobe: 0~20 Hz
Control
Operational Modes: Static, Color Fade, Auto Program, Sound Active, Master / Slave, DMX, Wireless DMX, iOS, Android
and IR Remote
Control Protocol: DMX512, Wireless DMX
DMX Channels: 6 / 10
Display: 4-button & 4-digit LED display control panel
Cooling: Fanless
Battery
Approx. 4 hours Full Colour
Approx. 15 hours Single Colour at Auto Run
Housing
Materials: Die-cast Aluminum
Finishing: Matte black
IP rating: IP20
Net Weight: 1.9 kg
Overall Size: 133 x 134 x 119 mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: w ww.event-lighting.com.au.