Event Lighting Fresnel User manual

Fresnel
Model No. F2X48
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
Ver 3.0

www.event-lighting.com.au
1
CONTENTS
Safety Instructions
- Power input & power Linking
Product Installation
- Fuse replacement
Diagrams
- Lux chart
- Dimensions
Control Board Operation
- DMX address setting
- DMX modes setting
- Manual colour setting
- Master/slave setting
DMX chart
Technical specifications
Warranty

www.event-lighting.com.au
2
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this number.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

www.event-lighting.com.au
3
Lux Chart
Dimensions

www.event-lighting.com.au
4
CONTROL BOARD OPERATION
Display Options / Values Function
DMX Add <001> - <508> To set DMX address
DMX Cha <01>, <02>, <05> To set DMX channel modes
Manual
Preset <StraW> <WarmW> <White>
<CoolW> <Steel>
To select colour from 5 preset colour temperature modes
Finetune <Straw> <Straw+> <Stra++>
<- -Warm> <-WarmW> <WarmW>
<WarmW+> <Warm++> <- -Whit><-White>
<White> <White+> <Whit++>
<- -Cool> <-CoolW> <CoolW> <CoolW+>
<Cool++> <- -Stee> <-Steel> <Steel>
To select colour from 21 fine tune colour temperature
modes
Dimmer <000> - <100> To set dimming intensity
Mas/Sla < Sla> / <Mas> To set Master/Slave modes
Reset <N> / <Y> To reset factory default setting
Update <N>/ <Y> Select to update firmware
<START> Use this fixture to update another fixture's software
DMX Addressing:
After selecting the "DMX Add" press “Enter”, use “Up” and “Down” buttons to select the desired DMX address, press
“Enter" to save new setting
DMX Modes
After selecting the "DMX Cha" press “Enter”, use “Up” and “Down” buttons to select the desired DMX mode, press
“Enter" to save new setting
Manual
After entering "Manual" mode, use “Up” and “Down” buttons to select the colour from preset colour group and fine tune
group, set intensity from 000 to 255, press “Enter" to save new setting
Master/Slave
Set the master fixture to one of the standalone operating modes.
Set the slave, enter "Mas/Sla" mode, set to “Slave”, press “Enter” to save the setting.
Firmware update
Use fixture A to update fixture B’s firmware
- Set fixture A to “Update” mode, select “Y” then select “START”
- Link fixture A and fixture B with DMX cable, then power up fixture B
- Press “Enter” on fixture A, fixture B’s firmware will be copied from fixture A.
*Ensure that fixture A and B are of the same type, otherwise damage may occur.
* Only fixture A and B should be in the DMX chain when updating firmware.

www.event-lighting.com.au
5
Fade Mode
DMX Chart
1 channels Mode
Channel Value Function
1 000 - 255 Dimmer & Colour temperature
2 channels Mode
Channel Value Function
1 000 - 255 Dimmer 0% ~ 100%
2 000 - 255 Warm white to cool white

www.event-lighting.com.au
6
5 channels Mode
Channel Value Function
1 000 - 255 Master dimmer coarse: 0% ~ 100%
2 000 - 255 Master dimmer fine: 0% ~ 100%
3 000 - 255 Warm white to cool white
4
000 - 007 Shutter closed (No light)
008 - 015 Shutter on
016 - 119 Strobe slow to fast (1-25Hz)
120 - 127 Shutter on
128 - 183 Strobe random slow to fast
184 - 191 Shutter on
192 - 247 Strobe audio sensitivity low to high
248 - 255 Shutter on
5 000 - 050 Standard
051 - 101 Stage
102 - 152 TV
153 - 203 Architect
204- 255 Theater

www.event-lighting.com.au
7
TECHNICAL SPECIFICATIONS
Power
Power Supply: 100~240V AC, 50/60 Hz
Power Consumption: 75W
Power Connection: Neutrik® PowerCON in / out
Photometrics
Light Source: 1 x 48W*2 cool white 5700K and warm white 2700K COB LED
CRI: 95
Beam Angle: 20° - 50°
Field Angle: 50° - 67°
Output: 1230 lux @3M at 20°, 395 lux @3M at 50°
Lens: 80mm Fresnel
PWM: 1,200Hz
LED Lifespan: 50,000 hours
Effects
Dimming: 16-bit 0 - 100%
Strobe: 1 – 25 Hz
Zoom: Manual Zoom 20° to 50°
Barn Door: Included
Gel Clip: Included
Control
Operational Modes: Manual, Master / Slave & DMX
Display: 4-button LCD control panel
DMX Protocol: DMX512
DMX Channel Mode: 1 / 2 / 5
DMX Interface: 3-pin XLR (Optional 5-pin XLR)
Housing
Housing Materials: Die- cast Aluminum Housing
Housing Finishing: Matte Black
Cooling: Fanless Cooling with Temperature Protection
Net Weight: 2.3 kg
Dimension: 202 X 139 X 193mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.