Event Lighting PARP12x8 User manual

PRO PAR
Model No. PARP12x8
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
Ver 33

www.event-lighting.com.au
1
CONTENTS
Safety Instructions
- Power input & power Linking
Product Installation
- Fuse replacement
Diagrams
- Dimensions
Control Board Operation
- Menu map
- Static colour mode chart
DMX chart
Technical specifications
Warranty

www.event-lighting.com.au
2
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Dimensions

www.event-lighting.com.au
3
CONTROL BOARD OPERATION
Menu Map
->
-
Select DMX address
->
or
Select DMX channel mode (CH-1: 4ch / CH-2: 9ch)
->
-
Set program speed
->
-
Select built-in program
->
Select sound active mode
->
-
Select static colour mode
(See static colour mode chart below)
->
-
Set strobe speed (Hz)
->
-
Set red colour intensity
->
-
Set green colour intensity
->
-
Set blue colour intensity
->
-
Set white colour intensity
->
-
Set dimmer speed
(nod0: fastest / nod4: slowest)
->
or
Toggle LED display on / off
->
Current operating temperature
->
Show current software version
->
or
Restore settings to factory default

www.event-lighting.com.au
4
Static colour mode
Value:
Function:
C1
Red
C2
Green
C3
Blue
C4
White
C5
Red + White
C6
Green + White
C7
Blue + White
C8
Green + Blue
C9
Red + Blue
C10
Red + Green
C11
Red + Green + Blue
C12
Green + Blue + White
C13
Red + Blue + White
C14
Red + Green + White
C15
Red + Green + Blue + White

www.event-lighting.com.au
5
DMX Chart
4 channels Mode
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
9 channels Mode
Channel
Value
Function
Note
1
000-255
Master DIMMER 0% ~ 100%
2
000-255
Red: 0% ~ 100%
3
000-255
Green: 0% ~ 100%
4
000-255
Blue: 0% ~ 100%
5
000-255
White: 0% ~ 100%
6
000-012
Strobe OFF
013-255
Strobe (slow-fast)
7
000-009
No Function
010-019
Program 1
020-029
Program 2
030-039
Program 3
040-049
Program 4
050-059
Program 5
060-069
Program 6
070-079
Program 7
080-089
Program 8
090-099
Program 9
100-109
Program 10
110-119
Program 11
120-129
Program 12
130-139
Program 13
140-255
Sound active mode
8
000-255
Speed of auto programs (slow ~ fast)
Ch7 must be set between
10-139
9
000-255
Colour fade time (jump ~ fade)
Mode must be set to “nod0”

www.event-lighting.com.au
6
TECHNICAL SPECIFICATIONS
Power
Input Voltage: 100~240V AC, 50/60 Hz
Power Consumption: 77W
Connection: IEC in
Fuse: T2A, 250V
Photometric
Light Source: 12pcs 4-in-1 RGBW 8W LED
Beam Angle: 25°
PWM: 1200 Hz
LED Lifespan: 50,000 hours
Effects:
Dimming: 0~100%
Strobe: 0~20 Hz
Control
Protocol: DMX512
DMX Channels: 4 / 9
Interface: 3-pin XLR in & out
Built-in Programming: Yes
Display: 4-button & 4-digit LED display control panel
Cooling: Fan
Housing
Materials: Metal & Flame retardant ABS
Finishing: Matte black
IP rating: IP20
Net Weight: 2.3 kg
Overall Size: 288 x 270 x 113 mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.