Event Lighting StrobeX User manual

Strobe
Model No. StrobeX
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au Ver 2.0

www.event-lighting.com.au
1
CONTENTS
Safety Instructions
- Power input & power Linking
Product Installation
- Fuse replacement
Diagrams
- Lux chart
Control Board Operation
- DMX address setting
- DMX modes setting
- Manual modes setting
- Auto run setting
- Master/slave setting
DMX chart
Technical specifications
Warranty

www.event-lighting.com.au
2
Safety Instructions
WARNING
•Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
•Do not look at the light source when the device is on.
•CAUTION: This unit's housing may be hot during and after operation.
•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
•Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
•Use a safety chain when mounting this device overhead.
•Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
•Do not operate this device if the housing, lenses, or cables appear damaged.
•Do not connect this device to a dimmer or rheostat.
•ONLY connect this device to a grounded and protected circuit.
•ONLY use the hanging bracket to carry this device.
•In case of a serious operating problem, stop using immediately.
•The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this number.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

www.event-lighting.com.au
3
Lux Chart
Menu Map
Address
<001> to <512>
DMX address
Channel
D4, S4, 6, 10
DMX channel modes
Manual
Strobe
<000> to <255>
Strobe speed, “0” no strobe, “001” to “255”, slow to
fast
BLOCK 1
<000> to <255>
Dimmer for Block 1
BLOCK 2
<000> to <255>
Dimmer for Block 2
BLOCK 3
<000> to <255>
Dimmer for Block 3
BLOCK 4
<000> to <255>
Dimmer for Block 4
Auto
Auto 1
Speed <000> to <255>
Select auto program and adjust auto run speed
Auto 2
Auto 3
Auto 4
….
Auto 12
Effect
on Auto
Dimmer
<000> to <255>
Adjust dimmer level and switch on strobe at
different speed for auto run
Strobe
<000> to <255>
Master
<Yes> or <No>
Select master/slave mode
Back L
ON
Back light always stays on
100s
Back light turns off after 100s
200s
Back light turns off after 200s
300s
Back light turns off after 300s
Temp.
Temp XXº
Display current temperature on LED panel
Info
Test 1
Test mode without strobe
Test 2
Test mode with strobe
Hour
Display the hours had been used
Recover
<Yes> or <No>
Recover to factory default

www.event-lighting.com.au
4
DMX Address
After select the “Address” and press “Enter”, use “Up”and “Down”button to select the desired DMX address, press
“Entre”to save new setting.
DMX Modes
After select the “Channel” and press “Enter”, use “Up”and “Down”button to select the desired DMX channel mode,
press “Entre”to save new setting.
Manual Mode
After select the “Manual" and press “Enter”, use “Up”and “Down”button to select the block intensity from 000 to 255.
Then select strobe speed from 000 to 255, press “Enter" to save new setting.
Auto Mode
This fixture has 18 built-in programs. Entered "Auto" mode, use “Up”and “Down”button to select the built-in programs
"Auto 1 ~ Auto 18", then press the "Enter" to confirm. Use “Up”and “Down”button to select the operating speed of the
program from 000 to 255, press “Enter" to save new setting. You have to use “Effect on Auto”mode to adjust the
brightness and add strobe effect to auto run.
Effect on Auto
Use “Effect on Auto”to switch on dimmer and strobe function to auto mode. Entered “Effect on Auto” mode, use “Up”
and “Down”button to select dimmer level, then press the "Enter" to confirm. Use “Up”and “Down”button to select
strobe speed from 000 to 255, press “Enter" to save new setting.
Master/Slave Mode
Set the master fixture to auto or manual modes.
Entered “Master”mode, use “Up”and “Down”button to select “No”, press “Enter” to set fixture to slave mode.
Use DMX to link master and slave fixture together.
DMX Data
When there is a ‘*’ flashing, the StrobeX is not receiving any DMX signal. A solid ‘*’ indicated DMX signal is being
received. DMX takes priority over all other functions when a signal is being received.
Once DMX signal is lost, the StrobeX will revert back to the original setting, which also could be DMX or Manual or
Automatic mode.
DMX Chart
S4 channels Mode
Channel
Value
Function
1
000-005
No Function
006-255
Block 1 strobe slow to fast
2
000-005
No Function
006-255
Block 2 strobe slow to fast
3
000-005
No Function
006-255
Block 3 strobe slow to fast
4
000-005
No Function
006-255
Block 4 strobe slow to fast

www.event-lighting.com.au
5
D4 channels Mode
Channel
Value
Function
1
000-009
No Function
010-255
Block 1 dimmer 0% ~ 100%
2
000-009
No Function
010-255
Block 2 dimmer 0% ~ 100%
3
000-009
No Function
010-255
Block 3 dimmer 0% ~ 100%
4
000-009
No Function
010-255
Block 4 dimmer 0% ~ 100%
6 channels Mode
Channel
Value
Function
1
000-009
No Function
010-255
Master dimmer 0% ~ 100%
2
000-255
Strobe On Duration Short to Long
3
000-005
No Function
006-255
Strobe Speed Slow to Fast
4
000-128
No Function
129-171
Strobe effect 1
172-214
Strobe effect 2
215-255
Strobe effect 3
5
000-005
No Function
006-015
Block 1 only
016-025
Block 2 only
026-035
Block 3 only
036-045
Block 4 only
046-055
Block 1, 2, 4 only
056-065
Block 1, 3 only
066-075
Block 3, 4 only
076-091
Auto chase 1
092-107
Auto chase 2
108-123
Auto chase 3
124-255
Auto combination
6
000-255
Auto Run Speed slow to fast

www.event-lighting.com.au
6
10 channels Mode
Channel
Value
Function
1
000-255
Master dimmer 0% ~ 100%
2
000-010
No Function
011-255
Block 1 dimmer 0% ~ 100%
3
000-010
No Function
011-255
Block 2 dimmer 0% ~ 100%
4
000-010
No Function
011-255
Block 3 dimmer 0% ~ 100%
5
000-010
No Function
011-255
Block 4 dimmer 0% ~ 100%
6
000-255
Strobe On Duration Short to Long
7
000-004
No Function
005-255
Strobe Speed Slow to Fast
8
000-128
No Function
129-171
Strobe effect 1
172-214
Strobe effect 2
215-255
Strobe effect 3
9
000-075
No Function
076-091
Auto chase 1
092-107
Auto chase 2
108-123
Auto chase 3
124-255
Auto combination
10
000-255
Auto Run Speed slow to fast

www.event-lighting.com.au
7
TECHNICAL SPECIFICATIONS
Input Voltage: 100V~240V AC, 50/60Hz
Power Consumption: 480W
Power Connection: fixed
Fuse: 5AT
Light Source: 936 pcs 0.5W 6500K SMD5730 Cool White LED
Beam Angle: 120°
Output: 1450 lux @3M
PWM: 2000Hz
LED Lifespan: 50,000 hours
Dimming: 0 –100%
Strobe: 0.5 –23 Hz
DMX Protocol: DMX512
DMX Channel Mode: S4 / D4 / 6 / 10
DMX Interface: 3-pin XLR
Built-in Programming: Yes
Display: 4-button LCD control panel
Cooling: Sensor thermostat controlled variable speed fan
Housing Materials: ABS & steel
Housing Finishing: Matte Black
Net Weight: 6 kg
Overall Size: 425 x 215 x 125 mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.