Event Lighting LM60S User manual

SPOT MOVING HEAD
LM60S
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to
change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting
for any clarification or information regarding this item.
www.event-lighting.com.au

1
www.event-lighting.com.au
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
This device can be mounted in many orientations provided each
individual device is secured by the use of correct mounting bracket.
Use a safety chain when mounting this device overhead.

2
www.event-lighting.com.au
Product Dimensions

3
www.event-lighting.com.au
Color Wheel
Colour DMX Value
Open 000-013
Colour 1 Red 014-031
Colour 2 Yellow 032-049
Colour 3 Sky blue 050-067
Colour 4 Green 068-085
Colour 5 Orange 086-103
Colour 6 Magenta 104-121
Colour 7 Blue 122-130

4
www.event-lighting.com.au
Rotating gobo wheel
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5

5
www.event-lighting.com.au
Menu operation
Display Function
1.DMX Address 001- 512 Select DMX address from 001 to 512
2.DMX Mode CH5 / CH15 Select DMX channel mode (CH5 / CH15)
3.Speed Mode Fade Speed / Fast Speed Set movement speed (Slow or Fast)
4.Master/Slave Master / Slave Select Master or Slave mode
5.Auto Mode Program1 - Program8 Select built-in program
6.Sound Mode OFF / ON Set sound active mode
7.Pan Rev OFF / ON Reverse Pan
8.Tilt Rev OFF / ON Reverse Tilt
9.Display Rev OFF / ON Reverse display
10.Sensitivity 000 - 100 Set sound sensitivity level
11.Factory Reset OFF / ON Restore settings to factory default
12.Calibration
All To Origin Clear PAN and TILT Home Position after 3s
Pan 000-120 Set calibration for Pan
Tilt 000-120 Set calibration for Tilt
Color 000-120 Set calibration for Color
Gobo 000-120 Set calibration for Gobo
Focus 000-120 Set calibration for Focus
Prism 000-120 Set calibration for Prism
13.Reset Reset

6
www.event-lighting.com.au
DMX Chart
5 channel Mode
Channel DMX Value Function
1 000 - 255 Pan Coarse
2 000 - 255 Tilt Coarse
3
000-007 No Function
008-047 Auto Play 1
048-087 Auto Play 2
088-127 Auto Play 3
128-167 Auto Play 4
168-207 Auto Play 5
208-247 Auto Play 6
248-255 Color Gobo Sound Control
4
000-007 No Function
008-032 X/Y Auto Run 1
033-058 X/Y Auto Run 2
059-084 X/Y Auto Run 3
085-110 X/Y Auto Run 4
111-136 X/Y Auto Run 5
137-162 X/Y Auto Run 6
163-188 X/Y Auto Run 7
189-240 X/Y Auto Run 8
241-255 X/Y Sound Control
5
000-050 No Function
051-100 High Speed Mode (react after 10S)
151-200 Low Speed Mode (react after 10S)
251-255 Reset (react after 10S)

7
www.event-lighting.com.au
15 channel Mode
Channel DMX Value Function
1 000 - 255 Pan coarse
2 000-255 Pan fine
3 000 - 255 Tilt coarse
4 000-255 Tilt fine
5 000 - 255 XY movement speed
6 000-255 Dimmer (Close to Open)
7
000-004 Shutter closed
005-250 Strobe effect slow to fast
251-255 Shutter open
8
000-013 Open(White)
014-031 Red
032-049 Yellow
050-067 Sky blue
068-085 Green
086-103 Orange
104-121 Magenta
122-130 Blue
131-139 Open (White)
140-195 Forward rainbow effect from fast to slow
196-199 Rotation stop
200-255 Backward rainbow effect from slow to fast
9
000-008 Open (White)
009-033 Gobo1
034-058 Gobo2
059-083 Gobo3
084-108 Gobo4
109-133 Gobo5
134-194 Forward rainbow effect from fast to slow
195-255 Backward rainbow effect from slow to fast
10
000-009 Stop
010-129 Forward Gobo Rotation from fast to slow
130-134 Stop
135-255 Backward Gobo Rotation from slow to fast
11 000-255 Focus
12
000-007 Open (White)
008-134 Prism
135-255 Forward Prism Rotation from slow to fast
000-007 No Function
008-047 Auto Play 1

8
www.event-lighting.com.au
13
048-087 Auto Play 2
088-127 Auto Play 3
128-167 Auto Play 4
168-207 Auto Play 5
208-247 Auto Play 6
248-255 Color Gobo Sound Control
14
000-007 No Function
008-032 X/Y Auto Run 1
033-058 X/Y Auto Run 2
059-084 X/Y Auto Run 3
085-110 X/Y Auto Run 4
111-136 X/Y Auto Run 5
137-162 X/Y Auto Run 6
163-188 X/Y Auto Run 7
189-240 X/Y Auto Run 8
241-255 X/Y Sound Control
15
000-050 No Function
051-100 High Speed Mode (react after 10S)
151-200 Low Speed Mode (react after 10S)
251-255 Reset (react after 10S)

9
www.event-lighting.com.au
TECHNICAL SPECIFICATIONS
Power
Input Voltage: 100~240V AC, 50/60 Hz
Power Consumption: 90W
Connection: IEC in
Fuse: T2A, 250V
Photometric
Light Source: 60W White LED
Beam Angle: 10°
Output: 5800lux @ 3M
PWM: 3000Hz
LED Lifespan: 20,000 hours
Colour 1 colour wheel (7 colour + open)
Gobo 1pc 5 patterns + open rotating wheel (outside Ø18.8mm, inside Ø13mm).
Effects 3-facet prism
Dimming: 0~100%
Strobe: 1~20 Hz
Focus: Linear via DMX
Movement 8 / 16 – bit
Pan: 540° (1.4 sec)
Tilt: 190° (0.8 sec)
Control
Protocol: DMX512
DMX Channels: 5 / 15
Interface: 3-pin XLR in & out
Built-in Programming: Yes
Sound Active: Yes
Display: 4-button 1 inch OLED display control panel
Cooling: Fan
Housing
Materials: Metal & Flame retardant ABS
Finishing: Matte black
IP rating: IP20
Net Weight: 4 kg
Overall Size: 330 x 200 x 280 mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.