Event Lighting PARTY VIVIDBAR2 User manual

VIVIDBAR2
24x 4W RGBW LED Lighting Bar
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version: 1

www.event-lighting.com.au
2
Safety Instructions
Warning
• Do not open this fixture, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look directly at the light source when the fixture is on.
Caution: This unit’s housing may become hot during and after operation.
• Install this fixture in a location with adequate ventilation, at least 50 cm from adjacent
surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or
connected to power.
• Use a safety chain when mounting this fixture overhead.
• Do not operate this device in any location where excessive dust, heat, water or humidity
may affect it.
• Do not operate this fixture if the housing, lenses, or cables appear damaged.
• Do not connect this fixture to a dimmer or rheostat.
• ONLY connect this fixture to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this fixture.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 40° C. Do not operate this fixture at higher
temperatures.
Power Input
This fixture has an auto switching power supply that works with an input voltage range of 110-
240V AC, 50/60 Hz.
Product Installation
• Attach the four parcans to the four mounting points on the controller bar.
• Connect the four parcans to the four cables on the controller bar.
• Insert the controller bar into the stand and tighten the screw to secure.
• Extend the tripod and place it on a stable surface.
Menu

www.event-lighting.com.au
3
Menu
Values
Description
d001-d512
001-A512
Set the DMX address.
IP.01-IP.64
001-512
IP mode
A1.01
A1.01-A1.19
Static colour mode. Press
enter to save.
A2.01
A2.01-A2.19
Jump colour change mode.
Press enter to save.
A3.01
A3.01-A3.19
Multicolour mode. Press enter
to save.
A4.01
A4.01-A4.19
Sound active mode. Press
enter to save.
A5.01
A5.01-A5.19
Strobe mode. Press enter to
save.
r.000
r.000-r.255
Red intensity
G.000
G.000-G.255
Green intensity
b.000
b.000-b.255
Blue Intensity
DMX Chart
This fixture is controlled by the universal DMX 512 protocol. The DMX address is the first
channel used to receive instructions from the external controller. For independent control,
each fixture must be assigned a unique address for each of its control channels. For
example, this device has one channel modes: 8, if it’s set to 8 channel mode, and there are
several fixtures need to be independently controlled, we just simply address first fixture at 1,
and second fixture at 9, third one at 17, etc. !
• If multiple fixtures have the same DMX address, they will behave synchronically. !
• Display will flash when no DMX signal is received. !
Channel
Min
DMX
Max
DMX
Function
1
0
10
No Function
11
50
Macro A1
51
100
Macro A2
101
150
Macro A3
151
200
Macro A4
201
255
Macro A5
250
255
Red+Green+Blue
2
0
255
Macro Colour
3
0
255
Macro Speed
4
0
255
Master Dimmer, 0-100%
5
0
255
Red dimmer, 0-100%
6
0
255
Green dimmer, 0-100%
7
0
255
Blue dimmer, 0-100%
8
0
255
White dimmer, 0-100%
! !

www.event-lighting.com.au
4
IR Remote
A1: Effect 1 – all lights on
Power button
A2: Effect 2 – colour jump
A3: Effect 3 – colour fade
A4: Sound active mode
A5: Strobe mode
Colour buttons: Colour adjustment
Speed buttons: Speed adjustment
DMX buttons: DMX channel selection
IP buttons: running effect
Technical Specifications
• Light Source: 24x 4W RGBW LEDs
• Beam angle: 25°
• Dimming: 0-100%
• Operation Modes: DMX, auto, manual, sound active, IR remote
• Control Interface: 3-pin XLR in/out, IR remote
• DMX Channels: 8
• Input Voltage: 110-240V AC, 50/60 Hz
• Power Consumption: 100W
Warranty
Please contact your local dealer or contact Event Lighting.
www.event-lighting.com.au