Event Lighting PAR4X12B User manual

PAR4X12B
4x 12W RGBWAU 6-in-1 Outdoor LED PAR
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0

www.event-lighting.com.au
1
Safety Instructions
Warning
•Do not open this device, there are no user serviceable parts inside. Risk of electric
shock.
•Do not look directly at the light source from close range.
•Avoid contact with the unit during operation, as the housing may become hot. Allow the
fixture to cool for at least 15 minutes after turning off before touching.
•Install this device in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
•Do not operate this device, or connect this device to power, within 50cm of any
flammable material.
•Use a safety chain when mounting this device overhead.
•Do not operate this device outdoors where excessive dust, heat, water, or humidity may
affect it.
•Do not operate this device if the housing, lenses, or cables appear damaged.
•Do not connect this device to a dimmer or rheostat.
•Do not operate this device at temperatures higher than 40°C (104°F).
•Only connect this device to a grounded and protected circuit.
•Only use the hanging bracket to carry this device.
•Stop using this device immediately if a serious operating problem becomes apparent.
Product Installation
PAR4X12B can be mounted in many orientations, provided each individual device is secured by
the use of the correct mounting bracket. Use a safety chain when mounting PAR4X12B
overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, replace the fuse with one of the same type of rating.
Before replacing the fuse, unplug the device from the power source.
Fuse Replacement Steps
1. Unscrew the fuse holder located on the rear panel from the housing.
2. Remove the old fuse from the holder.
3. Install the new fuse into the holder.
4. Place the fuse holder back into the housing and secure tightly.

www.event-lighting.com.au
2
Dimensions
Lux Chart
Distance (m)
1
2
3
4
5
Diameter (m)
Ø 0.73
Ø1.46
Ø2.18
Ø2.91
Ø 3.64
Red
308
72
33
18
13
Green
990
268
119
77
52
Blue
923
243
112
71
48
White
1263
345
156
102
73
Amber
340
87
42
25
18
UV
202
55
26
18
12
Full
3100
850
370
247
160

www.event-lighting.com.au
3
Control Board Operation
Menu Map
->
-
Select DMX address for 6 ch mode
->
-
Select DMX address for 10 ch mode
->
-
Remaining percentage of battery
power
->
or
Set dimming speed (SL: slow / FA:
fast)
->
or
When lost DMX signal,
ho: keep the last DMX signal state
OF: blackout
->
or
Switch on/off wireless DMX control
->
or
Switch on/off IR remote control
->
-
Set red colour intensity
->
-
Set green colour intensity
->
-
Set blue colour intensity
->
-
Set white colour intensity
->
-
Set amber colour intensity
->
-
Set UV colour intensity
->
-
Display IR control brightness level
->
-
Set strobe speed
->
-
Select 15 static colour modes, see
chart: Static colour mode
->
-
Select 16 speed of auto colour switch
mode
->
-
Select 16 speed of auto colour fading
mode
->
-
Select 16 speed of auto colour pulse
out mode
->
-
Select sound active mode with
different sound sensitive level
Wi-Fi Control Mode
Display current temperature
Display version number

www.event-lighting.com.au
4
->
or
Reset
Static Colour Mode
Value:
Function:
C1
R
C2
G
C3
R + G
C4
B
C5
B + R + UV
C6
G + B
C7
R + G + B + A + UV
C8
W
C9
R + W
C10
G + W
C11
R + A
C12
B + W + UV
C13
R + B + W + UV
C14
G + B + W
C15
R + G + B + W + A + UV
Wireless DMX Mode
Set Up Wireless DMX
PAR4X12B needs to be paired from the Wireless DMX transmitter. Follow the steps below to
pair:
1. Connect the DMX512 controller to the wireless DMX transmitter.
2. Switch on PAR4X12B, turn on the wireless DMX control on from control panel ‘rfon’
3. Set the PAR4X12B to DMX mode. (AXXX or dXXX)
4. Switch off PAR4X12B. Then, press and hold the ‘DMX select’ button whilst switching on
PAR4X124B. Once PAR4X12B turns on, the ‘wireless status’ light will be lit white and the
unit will be in ‘setup mode’.
5. The ‘wireless indicator’ will be lit to a specific colour to indicate the protocol being used
for the transmission as shown in TABLE1. Pressing the button will cycle through the
colours.
6. Once the desired protocol is selected, press the button for more than 1 second to save
the protocol. The transmitters, receivers and transceivers will remember the protocol
used even after a power cycle with their built-in memory chip.
Now, select either WDMX Mode or ELDMX Mode.
Table 1 Protocols
Colour
Protocol
Red
ELDMX Transmit and Receive
Green
WDMX Receive
Blue
WDMX G3 Transmit

www.event-lighting.com.au
5
Purple
WDMX G4 Transmit
Yellow
GZ Receive (Receiver Only)
Using WDMX Mode
Transmitters
Press the button to connect all unconnected receivers in the coverage area.
Press the button for 3 seconds to disconnect all receivers in the coverage area.
Receivers
Press the button for 3 seconds to disconnect the device from the transmitter it is currently
connected to.
Note: The colour of the light will indicate the group. Refer to Table 2 below.
Note: The receiver will not connect with a new transmitter unless it is disconnected first.
Table 2 WDMX Status Indicators
Protocol
Action
Description
W-DMX Receive
White
No connection
Red
Deleting Connection
Red Fast Flash
Connection Lost
Green Fast Flash
Connecting to Transmitter
Green Slow Flash
Connected but no DMX signal
Green
Connected with DMX signal
W-DMX Transmit
Red
Deleting All Receivers
Blue Fast Flash
Connecting with the receivers
Blue Slow Flash
No DMX input
Blue
Transmitting DMX
Using EL/GZ Wireless DMX Mode
Changing Channel Group
Press the button to display the current channel group being used.
Press the button again to cycle through the groups. The colour of the light will indicate the group
as shown in Table3.
Table 3 Status Indicators
Protocol
Action
Description
ELDMX / GZ
Solid Colour (Red, Green,
Blue, Yellow, Cyan, Purple,
White*)
1 of the 7* colour groups
(*7th white only in GZ mode, 6 in ELDMX mode)
Flashing Red
Transmitting DMX
Flashing Green
Receiving DMX

www.event-lighting.com.au
6
IR Remote Control Mode
•You must switch off wireless DMX function, select .
•Select , then use IR remote to switch on IR remote control mode.
Key
Function
Display
Description
Switch on/off IR function
to
or
your last
setting
Pressing <blackout> button to
switch on the fixture IR function,
fixture will go to CC12 auto colour
switch mode or your last setting
Pressing <blackout> button when
unit under IR mode, fixture will
blackout and on IR standby mode
Select auto colour switch mode
(CC) or auto colour pulse out
mode (CP) with different speed
between
Using <Auto> button to select CC
or CP mode, using to
change speed.
Select sound active mode (SU)
with different sensitivity level
Pressing <SOUND> button to
select SU mode, using
to change sensitivity level
Select auto colour fade mode
(dE) with different speed
Pressing <FADE> button to select
dE mode, using to
change speed.
Select manual colour mode
to
Pressing <MANUAL> button to
entry manual colour mode
Using
button to cycle though 20% change
of intensity of each colour
separately.
to
Pressing <MANUAL> button to quit
manual colour mode, fixture will
blackout
Select intensity of LED full on
mode
to
Pressing <%> button to cycle
though 10% change of intensity on
static colour
(R255+G255+B255+W255+A255+
U255) mode.
Select intensity of static colour
(R255+G255+B255+W255+A25
5+U255)
to
Using to change
intensity
Select intensity of static colour
(R255)
to
Using to change
intensity

www.event-lighting.com.au
7
Select intensity of static colour
(UV50+R255)
to
Using to change
intensity
Select intensity of static colour
(R255+G50)
to
Using to change
intensity
Select intensity of static colour
(G255)
to
Using to change
intensity
Select intensity of static colour
(G160+B255+UV100)
to
Using to change
intensity
Select intensity of static colour
(B255+UV50)
to
Using to change
intensity
Select intensity of static colour
(R50+B255+UV200)
to
Using to change
intensity
Select intensity of static colour
(R255+B150+UV255)
to
Using to change
intensity
Select intensity of static colour
(R255+B20+A200)
to
Using to change
intensity
Reset factory default setting
to
No function
Add strobe effect on CC, CP,
SU, dE, dl and static colour
mode.
No change
Pressing <STROBE> button to
cycle though 1/8 change of strobe
speed
Wi-Fi Mode
Downloading the application
Login to the App Store (iOS) or Google Play (Android) and download LED WiFi application. It
allows you to control the PAR4x12B using your mobile devices with iOS / Android operating
systems.

www.event-lighting.com.au
8
App Store (iOS) Google Play (Android)

www.event-lighting.com.au
9
Connecting mobile devices with iOS / Android to PAR4X12B
Step 1: On your mobile devices, select Settings > Wi-Fi > list of available Wi-Fi devices
Step 2: Select ‘LED_***’ and connect.
PAR4X12B has its own 3-digit Wi-Fi ID and is displayed as LED_***). “***” is based on the last
three digits of the serial number, which is printed on the back of PAR4X12B.
Step 3: Open LED Wifi application to control the light in 3 different modes.

www.event-lighting.com.au
10
DMX Chart
6-Channel Mode
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
5
000-255
Amber: 0% ~ 100%
6
000-255
UV: 0% ~ 100%
10 channel mode
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
5
000-255
Amber: 0% ~ 100%
6
000-255
UV: 0% ~ 100%
7
000-255
Master Dimmer 0% ~ 100%
8
000-255
Strobe (slow-fast)
9
000-050
No function
051-100
Select 15 Static colour mode (CL), colour have been controlled
by ch10
101-150
Select Auto colour switching modes (CC), program speed have
been controlled by ch10
151-200
Select Auto colour fade mode (dE), program speed have been
controlled by ch10
201-250
Select Auto colour pulse mode (CP), program speed have
been controlled by ch10
251-255
Select Sound active mode (SU), sound sensitivity level have
been controlled by ch10
10
(Ch9 set 051-
100)
000-015
No function
016-031
R
032-047
G
048-063
R + G
064-079
B
080-095
B + R + UV
096-111
G + B
112-127
R + G + B + A + UV
128-143
W
144-159
R + W
160-175
G + W
176-191
R + A
192-207
B + W + UV

www.event-lighting.com.au
11
208-223
R + B + W + UV
224-239
G + B + W
240-255
R + G + B + W + A + UV
10
(Ch9 set 101-
250)
000-255
Select auto run speed for (CC, dE and CP) from slow to fast
10
(Ch9 set 251-
255)
000-255
Select sound sensitivity level for sound active mode (SU) form
low to high

www.event-lighting.com.au
12
Technical Specifications
Power
•Input Voltage: 100~240V AC, 50/60 Hz.
•Power Pack: 16.8V DC 2A
•Power Consumption: 48W.
•Connection: DC Input socket.
Photometrics
•Light Source: 4x 12W 6-in-1 RGBWAU LEDs.
•Beam Angle: 40°.
•PWM: 20,000 Hz.
•LED Lifespan: 50,000 hours.
Effects
•Dimming: 0-100%.
•Strobe: 1-20 Hz.
Control
•Protocol: DMX512, Wireless DMX.
•DMX Channels: 6/10.
•Interface: Outdoor 3-pin XLR in and Outdoor 3-pin XLR out.
•Built-in Programming: 4 built-in auto modes.
•Display: 4-button & 4-digit LED Control Panel.
•Cooling: Fanless.
Battery
•Approx. 4 hours full colour.
•Approx. 15 hours single colour auto run.
Housing
•Materials: Die Cast Aluminium.
•Finishing: Matte Black.
•IP Rating: IP65.
•Net Weight: 1.9kg.
•Overall Size: 133x134x119 mm.
Warranty
Please refer to your local dealer or contact Event Lighting.