Event Lighting Lite LM7X30 User manual

LM7X30
7X30W LED WASH ZOOM HEAD
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are
subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions.
Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
V1.0

2
www.event-lighting.com.au
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent
surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity
may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher
temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC,
50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing
(anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

3
www.event-lighting.com.au
Product Installation
This device can be mounted in many orientations provided
each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.

4
www.event-lighting.com.au
Dimensions
Lux Chart
Lux Chart @ 6°
1m 3m 5m
Ø0.11 Ø0.31 Ø0.52
R 22,800 3,280 1,310
G 25,300 3,940 1,150
B 39,900 6,050 2,280
W 43,000 6,700 2,590
FULL 115,000 19,130 7,230
Lux Chart @ 60°
1m 3m 5m
Ø1.16 Ø3.46 Ø5.77
R 2,060 320 136
G 2,690 360 150
B 4,260 590 210
W 4,670 620 230
FULL 13,200 1,760 630

5
www.event-lighting.com.au
Menu operation
Menu – Move up a level.
Up – Move selection up one item.
Down – Move selection down one item.
Enter – Select / Move down a level.
Menu
MENU
DESCRIPTION
DMX
(Function
Mode)
Dmx Address
A001~AXXX
DMX Address Setting
Channel Mode
CH13
13 Channel Mode
CH15
15 Channel Mode
Auto Run
Program
1~8
Master/Alone
Auto Run State
Music Run
Program
1~8
Master/Alone
Music Control State
SET
(Fixture Set)
Reset Default
Yes/No
Reset to Default Setting
Signal Set
DMX
Wireless DMX
Wireless TX
Wired DMX
Wireless DMX Receiver
Wireless DMX Transceiver
Reverse Pan
(On/Off)
Reverse Pan
Reverse Tilt
(On/Off)
Reverse Tilt
Select Pan
630°/540°/360°
Select Pan (Default 540°)
Select Tilt
270°/180°/90°
Select Tilt(Default 270°)
Mic Sens.
0~99%
Microphone Sensitivity Setting
Hold on no DMX
(On/Off)
Hold or no hold when no Signal
(ON)复位状态
Limit Mode
OFF/Center/Right/Left
Select Edge or Corner Range
MAN
(Manual)
Reset
All
Pan/Tilt
Zoom
Reset all Settings
Reset Pan/tilt Settings
Reset Zoom Settings
Channel
PAN=XXX……
Manual Control Channel
ADV
(Advanced)
(Access Code
088)
Calibration
PAN=XXX……
Calibration

6
www.event-lighting.com.au
DMX Chart
Mode/Channel
Value
Function
17
15
1
1
Dimmer
0..255
Dimmer 0%...100%
2
2
Shutter
0..31
Shutter closed
32..63
Shutter open
64..95
Strobe effect slow to fast
96..127
Shutter open
128..159
Pulse effect, slow to fast
160..191
Shutter open
192..223
Random strobe effect, slow to fast
224..255
Shutter open
3
3
Pan
0..255
PAN Movement
4
Pan Fine
0..255
Fine control of Pan movement
5
4
Tilt
0..255
Tilt Movement
6
Tilt Fine
0..255
Fine control of Tilt movement
7
5
Zoom
0..255
In(near) to out(far)
8
6
Speed pan/tilt
0..225
Pan/tilt speed, fast to slow
226..235
Blackout during pan/tilt functions
236..255
TBD
9
7
Red
0..255
Red 0-100%
10
8
Green
0..255
Green 0-100%
11
9
Blue
0..255
Blue 0-100%
12
10
White
0..255
White 0-100%
13
11
Macro
0..15
TBD
16..31
Red
32..47
Green
48..63
Blue

7
www.event-lighting.com.au
64..79
White
80..95
Red+Green
96..111
Red+Blue
112..127
Red+White
128..143
Green+Blue
144..159
Green+White
160..175
Blue+White
176..191
R+G+B
192..207
R+G+B+W
208..223
Jump effect
224..239
Fading effect
240..255
Pulse effect
14
12
Macro Speed
0..255
Macro speed from slow to fast
15
13
Colour Temp
0..15
TBD
16..45
Below 3200K
46..75
3200K - 3500K
76..105
3500K - 5000K
106..135
5000K - 5500K
136..165
5500K - 6000K
166..195
6000K - 6500K
196..225
6500K - 7000K
226..255
7000K - 8000K
16
14
Visual Tungsten Lamp
0..15
TBD
16..255
Tungsten lamp effect is gradually enhanced
17
15
Special function
0..19
TBD
20..39
TBD
40..59
TBD
60..79
TBD
80..84
Reset all
85..94
Reset scan
95..99
Reset zoom
100..109
Internal program 1
110..119
Internal program 2
120..129
Internal program 3
130..139
Internal program 4
140..149
Internal program 5
150..159
Internal program 6

8
www.event-lighting.com.au
160..169
Internal program 7
170..179
Internal program 8
180..189
Internal sound program 1
190..199
Internal sound program 2
200..209
Internal sound program 3
210..219
Internal sound program 4
220..229
Internal sound program 5
230..239
Internal sound program 6
240..249
Internal sound program 7
250..255
Internal sound program 8
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to
receive instructions from the external controller. For independent control, each fixture must be
assigned its unique address control channels. For example, this device has two channel modes:
15/17, if we set the mode at standard 17 channels mode, and there are several models need to be
independently controlled, we just simply address first fixture at 1, and second fixture at 18, third one at
35, etc.
- If the devices have the same address, they will behave synchronically.
- Display is flashing when no DMX signal is received.

9
www.event-lighting.com.au
More Functions
- Software upgrade function via DMX cable. If there is any new firmware for this device, it can be
upgraded simply via a software upgrade box, without the need to change any mechanical parts.
The upgrade box is not included in the package, if you need any further assistance please contact
your authorized dealer.
- Hibernation. The device will enter sleeping mode if activated after a period of disconnecting DMX
signal to save power and will wake immediately when the DMX signal is sent or received again.
Technical Specifications
Power
• Input Voltage: 90~260V AC, 50/60 Hz
• Power Consumption: 240W
• Connection: PowerCon in
• Fuse: F4A, 250V
Photometric
• Light Source: 7pcs 30W RGBW LEDs
• Beam Angle: 6°~60°
• Output: 19,130lux @ 3m @ 6°
• PWM: 1,000Hz
• LED Lifespan: 50,000hours
Effects
• Dimming: 0~100%
• Strobe: 1.4~21Hz
• Zoom: 6°~60° linear via DMX
Movement
• 8/16 – bit, auto-reposition
• Pan: 360°/540°/630°
• Tilt: 90°/180°/270°
• Limit mode: Centre/Corner/Edge
Control
• Protocol: DMX512
• DMX Channels: 15/17
• Interface: 3-pin XLR in/out
• Built-in Programming: Yes

10
www.event-lighting.com.au
• Sound Active: Yes
• Display: 4-button 1.8inch TFT LCD display control panel
Housing
• Materials: Metal & flame retardant ABS
• Finishing: Matte black
• IP rating: IP20
• Cooling: Fan
• Net Weight: 6kg
• Rigging: 1pc omega brackets with 1/4- turn quick locks
WARRANTY
Please refer to your local dealer or contact Event Lighting Pty Ltd.