Event Lighting PAR6X12OB2 User manual

PAR6X12OB2
6x 12W RGBWAU 6-in-1 Outdoor Battery LED PAR
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0

www.event-lighting.com.au
1
Safety Instructions
Warning
• Do not open this fixture, there are no user serviceable parts inside. Risk of electric shock.
• Do not look directly at the light source from close range.
• Avoid contact with the unit during operation, as the housing may become hot. Allow the
fixture to cool for at least 15 minutes after turning off before touching.
• Install this fixture in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
• Do not operate this fixture, or connect this device to power, within 50cm of any flammable
material.
• Use a safety chain when mounting this fixture overhead.
• Do not operate this fixture outdoors where excessive heat or water may affect it.
• This fixture is IP65 certified, meaning that it is protected against dust ingress, and
protected against low pressure water jets from any direction. Ensure all protective covers
are sealed correctly.
• Do not operate this fixture if the housing, lenses, or cables appear damaged.
• Do not connect this fixture to a dimmer or rheostat.
• Do not operate this fixture at temperatures higher than 40°C (104°F).
• Only connect this fixture to a grounded and protected circuit.
• Only use the hanging bracket to carry this fixture.
• Stop using this fixture immediately if a serious operating problem becomes apparent.
Product Installation
PAR6X12OB can be mounted in many orientations, provided each individual device is secured
by the use of the correct mounting bracket. Use a safety chain when mounting PAR9X12OB
overhead.
IMPORTANT: Only use the provided Outdoor DMX cable in the device’s DMX out
port. Use of other cables will cause the cable to become stuck in the port,
requiring the unit to be repaired.

www.event-lighting.com.au
2
Dimensions
Lux Chart

www.event-lighting.com.au
3
Control Operation
Button Operation
Menu: Return to the previous screen.
Up: Move selection up.
Down: Move selection down.
Enter: Confirm the selection.
Button Lock
While on the home screen, press Down for 3
sec to lock all buttons, preventing accidental
input. While locked, press Down for 3 sec to
unlock.
Wireless DMX Setup
To pair PAR6X12OB2 to a wireless DMX transmitter:
1. Connect a DMX controller to the wireless DMX transmitter.
2. Press Power switch to turn on PAR6X12OB2 and enable wireless DMX from the control
panel: Setting > Wireless > Wireless EN > ON. To turn on the wireless indicator, go to
Settings > Display > Wireless LED > ON.
3. Set PAR6X12OB2 to Slave mode from the control panel: Setting > DMX Setting > Slave
mode.
4. Press Power to select the WDMX channel group. Every time the power button is
pressed, the selected WDMX channel group will be changed. The colour of the LED
indicates the currently selected channel group, there are six different groups.
5. Press the button on the wireless DMX transmitter to change its channel group. The
selected group needs to be the same as the one on the fixture.
6. Once the pairing is successful, the indicator light on the wireless DMX transmitter will
flash red. The indicator light on the PAR6X12OB2 will flash green.
Power Switch
1. Short press the Power button then release it to turn on the PAR6X12OB2.
2. Long press the Power button until the indicator light flashes green, then release the
Power button to turn off the fixture.
3. Every time the Power button is pressed when the PAR6X12OB2 is on, the wireless DMX
mode will be changed.
4. Press and hold the Power button for 30 seconds to reset to factory settings. The indicator
light will flash red.

www.event-lighting.com.au
4
Menu
Level 1
Level 2
Level 3
Level 4
Level 5
Function/Description
Preset
ID
Select static colour mode, 0-39.
Master
Master dimmer, 0-100%
Red
Red, 0-255
Green
Green, 0-255
Blue
Blue, 0-255
White
White, 0-255
Amber
Amber, 0-255
UV
UV, 0-255
Colour
ID
Select static colour mode, 0-63.
Master
Master dimmer, 0-100%
Effects
Chase
Built in chase
Select a built in chase, 0-9.
User chase
Select a user chase, 0-7.
Edit
chase
Edit
scene:
0-63
Add
scene:
0-63
Red
Ref. number: 0-103
Green
Blue
White
Amber
UV
Delete scene
Fading
Jumping
Pulse
Master
Master dimmer, 0-100%
Speed
Effect speed, 0-255
Fade
Fade brightness, 0-100%
Strobe
Strobe
Strobe, 0-255
Colour
Master
Master dimmer, 0-100%
Red
Red, 0-255
Green
Green, 0-255
Blue
Blue, 0-255
White
White, 0-255
Amber
Amber, 0-255
UV
UV, 0-255
Sound
Sound Enable
Off/On
Sensitivity
0-9
Brightness
0-9
Settings
DMX
Setting
DMX Address
Set DMX address, 0-512
Master/Slave
Set master/slave mode
Channel Mode
Set DMX channel mode, Normal (12)/
Simple (6)

www.event-lighting.com.au
5
When no DMX
Behaviour when DMX signal lost, OFF/
Hold/ Power up/ Last action
Wireless
Wireless En
Wireless DMX, Off/On
Display
Screen Mode
Status/ On/ Off/ Logo
Screen Time
Inactivity time for screen off, 0-255 sec
Wireless LED
Wireless indicator light, On/Off
General
Power-
up
Preset
Preset on power up, 0-39
Colour
Colour on power up, 0-39
Chase
Chase on power up, 0-20
Last set
Last setting on power up
Battery Mode
Bright/Normal/Life
Dim Response
LEDs/Fast/Less Fast/Middle/Slow
Dimming Curve
Linear/Log/S Curve/Exp
RDM Enable
On/Off
IR Enable
On/Off
Power off Bat
Power off when battery depleted to this
percentage, 0-50%
Top Temp
25-125 degrees
Password
Password
Off/On
Set Password
Enter default password, Menu-Up-Enter-
Down, then enter a new password
Time
Time
Enter the current time
Power On
Power on fixture and start selected
program at this time
Power Off
Power off at this time
Load
Factory
MENU
Cancel
ENTER
Reset to factory default
Status
LED
Current
Bright
0-100
Red
0-100
Green
0-100
Blue
0-100
White
0-100
Amber
0-100
UV
0-100
Temperature
Battery Voltage
DMX Channel
RDM UIDI
RDM U1D2
Software: BAT-6S02
Version: May 04 2022

www.event-lighting.com.au
6
DMX Chart
Mode/Channel
Min
DMX
Max
DMX
Function
6 ch
12 ch
1
0
255
Master dimmer, 0-100%
1
2
0
255
Red, 0-100%
2
3
0
255
Green, 0-100%
3
4
0
255
Blue, 0-100%
4
5
0
255
White, 0-100%
5
6
0
255
Amber, 0-100%
6
7
0
255
UV, 0-100%
8
0
255
Strobe, slow to fast
9
0
8
No function
9
127
40 preset colours
128
255
63 factory colours
10
0
19
No function
20
89
18 chases
90
127
Custom chases
128
159
63 colour fade
160
191
63 colour jump
192
223
63 colour pulse
224
255
Sound active mode
11
0
255
Auto run speed, slow to fast
12
0
5
No function
6
55
Dimming speed 1
56
105
Dimming speed 2
106
155
Dimming speed 3
156
205
Dimming speed 4
106
255
Dimming speed 5

www.event-lighting.com.au
7
IR Remote
BLACK OUT
Press <Blackout> once to turn off the fixture, press any of 0-9 button to turn on the fixture.
AUTO
Automatic mode will enable you to run the chase programs on the fixture.
1. Press <AUTO> on the remote controller to turn on the Jump mode.
2. Press <BLACK OUT> to turn off the Jump mode.
SOUND
Sound-Active mode will enable the fixture to respond to music.
1. Press <SOUND> on the remote controller to turn on sound-active mode.
2. Press <BLACK OUT> to turn off the sound mode.
SENSITIVITY
To adjust sensitivity for sound mode:
1. Press < SENSITIVITY > on the remote controller.
2. Press <+> or < - > to adjust sound sensitivity.
STROBE
1. Press < STROBE > on the remote controller.
2. Press <+> or < - > to adjust strobe frequency, press <STROBE> again to turn off the strobe.
SPEED
Adjust the speed of Jump / Pulse / Fade programs
1. Press <SPEED> on the remote controller.
2. Press <+> or < - > to adjust the program speed.
FADE
1. Press <FADE> to turn on the fading program
2. Press <+> or < - > to adjust Fade Depth
3. Press <BLACK OUT> to turn off the fading.
MANUAL
1. Press <MANUAL> to turn on colour mode.
2. Press <R>, <G>, <B>, <W>,<A> or <UV> to select red, green, blue, white, amber or UV.
3. Press <+> or < - > to adjust percentage of each colour
%
1. Press <%> on the remote controller to turn on the Pulse program
2. Press <BLACK OUT> to turn off the pulse grogram.
NUMBER 0~9
Preset colours, press a button 0-9 to turn on the corresponding colour.

www.event-lighting.com.au
8
Technical Specifications
Photometrics
• Light Source: 6x 6-in-1 RGBWAU 12 W LEDs
• Beam Angle: 40°
• Output: 3820 lux on @ 1 m RGBWAU Full on
• PWM: 20,000 Hz
• LED Lifespan: 50,000 hours
Effects:
• Dimming: 0~100%
• Strobe: 0~20 Hz
Power
• Input Voltage: 100~240V AC, 50/60 Hz, 72 W
• Connection: Seetronic® Outdoor True1 in
Control
• Operation Modes: DMX, Wireless DMX, manual, auto, sound active, master/slave, IR
Remote
• Control Protocol: DMX512, Wireless DMX, IR
• Interface: 3-pin DMX in/out
• DMX Channels: 6 / 12
• Display: 4-button OLED control panel
Battery
• Single Colour (hr): up to 20
• Full Colour (hr): up to 4
Housing
• Materials: Die-cast aluminium, matte black finish
• Cooling: Fanless
• IP rating: IP65
• Net Weight: 3 kg
• Overall Size: 240 x 165 x 210 mm
Accessories
• Charging Road Case: PAR6CASEWC
Warranty
Please refer to your local dealer or contact Event Lighting.