Everbloom E281719 User manual

You need at least 18” x 20” (46 x 51cm) for the finished
product. A flat and firm area (like a garage floor or flat
yard space) is perfect! The only tool you may need is a
rubber mallet.
Small parts are included; we advise you to keep
them away from children and pets.
We alsosuggest having another person help you
assemble. Maximum Load Capacity: approximately
2.8 cu. ft. of soil
Questions or Comments?
Email us at [e-mail]
Everbloom-Garden.com
Elevated Planter Box
Installation Guide
Thank You!
You’re only a few steps away from your perfect vegetable
garden or elevated planter. We hope you enjoy!
Before You Start
Please read the instructions carefully to familiarize
yourself with every detail and step involved. Keep this
manual for futurereference. Findasuitable space to
assemble your new Elevated Planter Box.
Important Notes
Model# E281719 / E281719G
Dimensions 17" L x 19" W x 28" H
1
Subscribe at www.everbloom-garden.com
for extra savings and upgrading information!

Elevated Planter Box - 17" L x 19" W x 28" H
Parts List
2
Garden Bed
Liner
X 1
Post Cap
X 4
Right Corner
Post
X 2
Left Corner
Post
X 2
+ 2pc
replacement
Top
Bottom
Top
Bottom
Short
Board A
X 4
420mm
Bottom
Board
X 2
460mm
Short
Board B
X 4
420mm

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
3
IMAGE1
10”
(25cm)
Short Board A Short Board A
Short Board B Short Board B
Bottom Boards
Depth 1 - 10” from page 4
IMAGE2
Depth 2 - 7.5” from page 10
There are 2 different assembly methods providing 2 different planting depths: 10” (as shown in
Image 1) and 7.5” (as shown in Image 2).
* For deeper planting depth of 10”, please follow steps from page 4.
* For easier but shallower planting depth of 7.5”, please go to page 10.
7.5”
(19cm)
Bottom Boards

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
4
IMAGE3IMAGE4
Top
Bottom
Start by makingsure each corner post is oriented correctly, as shown in Image 3. Slide one short board B
into the corner brackets from above.
Note: Theshort boards need to be placed in the inward “U” shape of the brackets, as shown in Image 4.
Left
Corner
Post
Right
Corner
Post
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
5
IMAGE5
Left Corner
Post
Left Corner
Post
Right Corner
Post
Right Corner
Post
Short
Board B
Slide another short board B into the other two corner brackets from above, as shown in Image 5.
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
6
IMAGE6
With the help of another person holding the 2 assembled parts, slide another two short boards Binto the
brackets from above. Make sure that one short board B goes straight to the bottom, while the other one
stays in the middle of the way (don’t push to the bottom), with the top edge between the 2nd and 3rd holes
of the post.
Short
Board B
Short
Board B
in the
middle of
the way
to the
bottom

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
7
IMAGE7
Put the bottom boards on lower slots of short boards B. Make sure the 2 ends of these bottom boards go
into the lower slots and rest in them with enough contact as shown in Image 7. Adjust the height of the
higher short board B slightly to hold these bottom boards ifnecessary.
Bottom
Board x 2
lower slot
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
8
IMAGE8
Push down the higher short board B to the bottom, as shown in Image 8.
Short
Board B
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
9
IMAGE9
Slide the remaining boards into place, as shown in Image 9. Now you get an elevated planter box with 10”
planting depth. Then, go to page 15, and follow the steps afterwards.
Short
Board A
x 4
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
10
IMAGE3aIMAGE4a
Top
Bottom
Start by makingsure each corner post is oriented correctly, as shown in Image 3a. Slide one short board B
into the corner brackets from above.
Note: Theshort boards need to be placed in the inward “U” shape of the brackets, as shown in Image 4a.
Left
Corner
Post
Right
Corner
Post
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
11
IMAGE5a
Left Corner
Post
Left Corner
Post
Right Corner
Post
Right Corner
Post
Short
Board B
Slide another short board B into the other two corner brackets from above, as shown in Image 5a.
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
12
IMAGE6a
With the help of another person holding the 2 assembled parts, slide the other two short boards Binto the
brackets from above, as shown in Image 6a.
Short
Board B
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
13
IMAGE7a
Put the bottom boards on the long support boards, as shown in Image 7a.
Bottom
Board
x 2
Short
Board B
Short
Board B

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
14
IMAGE8a
Slide the remaining boards into place, as shown in Image 8a. Now you get an elevated planter box with
7.5” planting depth.
Short
Board B
Short
Board A
x 4

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
15
IMAGE10
If necessary, use your rubber mallet to ensure the boards are tightly in place. Cover the brackets with the 4
end caps, as shown in Image 10.
Rubber
Mallet
Post Cap
X 1
Post Cap
X 1
Post Cap
X 1
Post Cap
X 1

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
16
IMAGE 11
x 8
IMAGE12
For additional stability, we highlysuggest using the included 8 self-tappingscrews with washers (Image 11).
Fasten 2screws into each side of the inward facing corner posts using a #2 Phillips screwdriver (not includ-
ed), as shown in Image 12.
Screws also can be fastened from outside, as shown in Image 13.
Do not fasten the screws into the same height holes facing to each other on the same post.
IMAGE13

Elevated Planter Box - 17" L x 19" W x 28" H
Assembly
17
IMAGE14
IMAGE15
Garden Bed
Liner
Unfold the liner and cover the bottom of the garden bed, as shown in Image 14 and Image 15.

Elevated Planter Box - 17" L x 19" W x 28" H
Note
18
IMAGE16
X
X
Sometimes there might be a misalignment of the Corner Posts as shown in Image 16 and Image 17, which
may resultin difficulty of sliding boards into the brackets. Please adjust them to the right position so that they
are parallel to each other, and perpendicular to the ground.
Assembling Problem 1
IMAGE17
Assembling Problem 2

Bloom On.
Distributed by:
Dynaforge Trading LLC
St. Paul, MN55101
Email: [e-mail]
Everbloom-Garden.com
US Patent Pending
Subscribe at www.everbloom-garden.com for
extra savings and upgradinginformation!