evertz 2431RX-2 User manual

2431RX-2
Dual Path Serial Digital to DVI Converter
Instruction Manual
© Copyright 2014
EVERTZ MICROSYSTEMS LTD.
5288 John Lucas Drive,
Burlington, Ontario,
Canada L7L 5Z9
Phone: [phone]
Sales: [email protected] Fax: [phone]
Tech Support: [email protected] Fax: [phone]
Web Page: http://www.evertz.com
Version 1.0, March 2014
The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended solely for
the use of purchasers of the 2431RX-2 Series products. Evertz Microsystems expressly prohibits the use of this manual for any
purpose other than the operation of the device. Due to ongoing research and development, features and specifications in this
manual are subject to change without notice.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz Microsystems
Ltd. Copies of this manual can be ordered from your Evertz dealer or from Evertz Microsystems.

This page left intentionally blank

INFORMATION TO USERS IN EUROPE
NOTE
CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to the European Union EMC directive. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
INFORMATION TO USERS IN THE U.S.A.
NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s
authority to operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables
with the shield connected to the chassis ground of the device must be used.

This page left intentionally blank

2431RX-2
Dual Path Serial Digital to DVI Converter
Revision 1.0 Page i
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 First Release Mar 2014
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof, nor for the rights of third
parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of Evertz products are for informational
use only and are not warranties of future performance, either expressed or implied. The only warranty offered by Evertz in relation to this product is the Evertz standard
limited warranty, stated in the sales contract or order confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is granted nor liability
assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation. Information contained in this manual is
periodically updated and changes will be incorporated into subsequent editions. If you encounter an error, please notify Evertz Customer Service department. Evertz
reserves the right, without notice or liability, to make changes in equipment design or specifications.

2431RX-2
Dual Path Serial Digital to DVI Converter
Page ii Revision 1.0
This page left intentionally blank

2431RX-2
Dual Path Serial Digital to DVI Converter
TABLE OF CONTENTS Revision 1.0 Page iii
TABLE OF CONTENTS
1. OVERVIEW ...................................................................................................................................1
2. SPECIFICATIONS.........................................................................................................................3
2.1. SERIAL INPUTS...................................................................................................................3
2.2. OPTICAL INPUT...................................................................................................................3
2.3. DVI OUTPUTS......................................................................................................................3
2.4. ANALOG AUDIO OUTPUT...................................................................................................3
2.5. ELECTRICAL .......................................................................................................................3
2.6. PHYSICAL............................................................................................................................4
2.7. COMPLIANCE......................................................................................................................4
3. INSTALLATION.............................................................................................................................5
3.1. POWER ................................................................................................................................5
3.2. DVI-I CONNECTORS............................................................................................................5
3.3. BNC CONNECTORS............................................................................................................6
3.4. FIBER CONNECTORS (OPTIONAL)....................................................................................6
3.5. DB9 CONNECTOR...............................................................................................................7
3.6. CARE AND HANDLING OF OPTICAL FIBER......................................................................8
3.6.1. Safety........................................................................................................................8
3.6.2. Handling and Connecting Fibers................................................................................8
3.6.3. Making Sure the Optical Fibers are Clean..................................................................8
3.7. STATUS LEDS .....................................................................................................................9
3.8. USER CONTROLS .............................................................................................................10
3.8.1. Dip Switches............................................................................................................10
4. CONFIGURATION.......................................................................................................................11
4.1. ACCESSING THE SERIAL PORT MENU...........................................................................11
4.2. SERIAL MENU ...................................................................................................................11
4.2.1. Network Configuration .............................................................................................12
4.2.2. Hardware Version Information .................................................................................12
4.2.3. Video Utilities Menu.................................................................................................13
4.2.3.1. Video Standard Information.......................................................................13

2431RX-2
Dual Path Serial Digital to DVI Converter
Page iv Revision 1.0 TABLE OF CONTENTS
4.2.3.2. Lock Video Input Mode..............................................................................14
4.2.3.3. YCBCR Decimation Settings.....................................................................14
4.2.3.4. Set Output Color on Signal Loss ...............................................................15
4.2.3.5. Enable Deinterlacing.................................................................................15
4.2.3.6. Enable Agile Locking.................................................................................16
4.2.3.7. ANX9806 Status Check.............................................................................16
4.2.3.8. Get EDID...................................................................................................17
4.2.3.9. Video Processing Settings.........................................................................17
4.2.4. Scaler Configuration................................................................................................21
4.2.5. Under Monitor Display Setup:..................................................................................23
4.2.6. SNMP Configuration................................................................................................27
4.2.6.1. SNMP V3 Setup Menu..............................................................................27
4.2.6.2. SNMP Version...........................................................................................32
4.2.7. SNTP Setup.............................................................................................................34
4.2.8. Clock Setup.............................................................................................................37
4.2.9. Engineering Menu....................................................................................................38
5. UPGRADING FIRMWARE ..........................................................................................................39
5.1. UPDATE PROCEDURE......................................................................................................39
5.1.1. Part 1 – Configuring the Unit for Firmware Upgrades...............................................39
5.1.2. Part 2 – Terminal Program Setup ............................................................................39
5.1.3. Part 3 – Uploading the New Firmware .....................................................................40
5.1.4. Part 4 – Completing the Upgrade.............................................................................40
5.2. FTP UPGRADE METHOD..................................................................................................41
6. 2431RX-2 CONFIGURATION USING VISTALINK®PRO.............................................................43
6.1. SNMP V1 ............................................................................................................................43
6.2. CONFIGURING VLPRO FOR SNMP V3.............................................................................45
6.3. 2431RX-2 VISTALINK®CONFIGURATION VIEW..............................................................48
6.3.1. General Tab.............................................................................................................49
6.3.2. Input Monitoring.......................................................................................................50
6.3.3. Input Controls..........................................................................................................51
6.3.4. Output Monitoring....................................................................................................51
6.3.5. Output Controls .......................................................................................................52
6.3.6. Video Processing Tab..............................................................................................53
6.3.7. UMD Output Controls ..............................................................................................54
6.3.8. SNTP Controls.........................................................................................................55
6.3.9. Faults Tab ...............................................................................................................56
6.3.10. Faults Controls Tab .................................................................................................56

2431RX-2
Dual Path Serial Digital to DVI Converter
TABLE OF CONTENTS Revision 1.0 Page v
FIGURES
Figure 1-1: 2431RX-2 Block Diagram...............................................................................................................2
Figure 3-1: 2431RX-2 Rear View......................................................................................................................5
Figure 3-2: 2431RX-2 Rear View – DVI-I Connectors......................................................................................6
Figure 3-3: 2431RX-2 Rear View – BNC Connectors.......................................................................................6
Figure 3-4: 2431RX-2 Rear View – Fiber Connectors......................................................................................6
Figure 3-5: 2431RX-2 Front View – DB9 Connector ........................................................................................7
Figure 3-6: 2432TX-2 Status LEDs...................................................................................................................9
Figure 3-7: 2431RX-2 DIP Switches...............................................................................................................10
Figure 4-1: 2431RX-2 Serial Menu .................................................................................................................11
Figure 4-2: Network Configuration..................................................................................................................12
Figure 4-3: Hardware Version Information......................................................................................................12
Figure 4-4: Video Utilities Menu......................................................................................................................13
Figure 4-5: Video Standard Information..........................................................................................................13
Figure 4-6: Lock Video Input Mode.................................................................................................................14
Figure 4-7: YCBCR Decimation Settings........................................................................................................14
Figure 4-8: Set Output Color on Signal Loss..................................................................................................15
Figure 4-9: Enable Deinterlacing ....................................................................................................................15
Figure 4-10: Enable Agile Locking..................................................................................................................16
Figure 4-11: Get EDID ....................................................................................................................................17
Figure 4-12: Video Processing Settings..........................................................................................................17
Figure 4-13: Print VPROC CTRL Numbers ....................................................................................................18
Figure 4-14: Gain Level Controls....................................................................................................................19
Figure 4-15: Gamma Level .............................................................................................................................19
Figure 4-16: Red, Green, Blue Gamma Levels ..............................................................................................19
Figure 4-17: RGB Limiter................................................................................................................................20
Figure 4-18: Set VPROC Value ......................................................................................................................20
Figure 4-19: Initialize Default Values..............................................................................................................20
Figure 4-20: Scaler Configuration...................................................................................................................21
Figure 4-21: Enable/Disable Scaler................................................................................................................21
Figure 4-22: Select Scaler Mode Settings ......................................................................................................22
Figure 4-23: Select Scaler Crop Settings........................................................................................................22
Figure 4-24: Under Monitor Display Setup......................................................................................................23
Figure 4-25: UMD Line Data...........................................................................................................................26
Figure 4-26: SNMP Configuration Menu.........................................................................................................27
Figure 4-27: SNMP V1 Setup Menu ...............................................................................................................27
Figure 4-28: SNMP V3 Setup Menu ...............................................................................................................27
Figure 4-29: SNMP V3 User Setup.................................................................................................................28
Figure 4-30: Add/Edit SNMP V3 User.............................................................................................................28
Figure 4-31: Remove SNMP V3 User.............................................................................................................29
Figure 4-32: Show All SNMP V3 User ............................................................................................................29
Figure 4-33: SNMP V3 Access Control Setup................................................................................................29
Figure 4-34: Add SNMP V3 Access Control...................................................................................................30
Figure 4-35: Remove SNMP V3 Access Control............................................................................................30
Figure 4-36: Show All SNMP V3 Access Control ...........................................................................................31
Figure 4-37: SNMP V3 Notification Setup.......................................................................................................31
Figure 4-38: Add SNMP V3 Notification Destination ......................................................................................31
Figure 4-39: Remove SNMP Notification........................................................................................................32
Figure 4-40: SNMP Version............................................................................................................................32
Figure 4-41: SNMO Get Set Version Setup....................................................................................................33
Figure 4-42: SNMP Trap Version Setup.........................................................................................................33
Figure 4-43: SNTP Setup................................................................................................................................34
Figure 4-44: Set NTP Server Address............................................................................................................34
Figure 4-45: Enable Daylight Savings Time....................................................................................................35

2431RX-2
Dual Path Serial Digital to DVI Converter
Page vi Revision 1.0 TABLE OF CONTENTS
Figure 4-46: Daylight Saving Start Time.........................................................................................................35
Figure 4-47: Daylight Savings End Time........................................................................................................36
Figure 4-48: Clock Setup - Set Offset.............................................................................................................37
Figure 4-49: Clock Setup – Set Offset Dir ......................................................................................................37
Figure 4-50: Clock Setup – Set Time Format.................................................................................................38
Figure 4-51: Clock Setup – Set Date Format..................................................................................................38
Figure 6-1: Configuring VistaLINK®PRO .......................................................................................................43
Figure 6-2: Configuration Page for 2431RX-2................................................................................................44
Figure 6-3: Server SNMP Communications User...........................................................................................45
Figure 6-4: Add an SNMP Name for the SNMP V3 Role ...............................................................................45
Figure 6-5: Add Authentication Password ......................................................................................................46
Figure 6-6: Edit Username..............................................................................................................................46
Figure 6-7: SNMP V3 Group(s) Authentication...............................................................................................47
Figure 6-8: Configure 2431RX-2 with VistaLINK®Pro....................................................................................48
Figure 6-9: Main configuration Screen............................................................................................................49
Figure 6-10: General Tab Menu .....................................................................................................................49
Figure 6-11: Input Monitoring..........................................................................................................................50
Figure 6-12: Input Controls.............................................................................................................................51
Figure 6-13: Output Monitoring.......................................................................................................................51
Figure 6-14: Output Controls ..........................................................................................................................52
Figure 6-15: Video Processing Tab................................................................................................................53
Figure 6-16: UMD Output Controls.................................................................................................................54
Figure 6-17: SNTP Controls ...........................................................................................................................55
Figure 6-18: Faults Tab...................................................................................................................................56
Figure 6-19: Fault Controls Tab......................................................................................................................56
TABLES
Table 2-1: DVI-I Input Connector......................................................................................................................5
Table 2-2: DB9 Port Pin Out.............................................................................................................................7
Table 3-3: DIP Switch Functions ....................................................................................................................10
Table 4-1: Serial Port Terminal Settings.........................................................................................................11
Table 6-1: Serial Terminal Settings ................................................................................................................39
Table 6-2: Serial Terminal Settings ................................................................................................................41

2431RX-2
Dual Path Serial Digital to DVI Converter
OVERVIEW Revision 1.0 Page - 1
1. OVERVIEW
The 2431RX-2 is a versatile dual path serial digital to DVI converter. The 2431RX-2 is used for projects
where high density extension of DVI over coax or fiber is required. 2431RX-2 is used as part of the EFX
system for video wall and command center projects. This self-contained module accepts up to two serial
inputs over coax or fiber (with additional SFP) and converts them to single link or dual link DVI with a
resolution range of up to WQXGA (2560x1600). The possibility to support two paths simultaneously
makes the 2431RX-2 a very cost effective Professional AV solution.
2431RX-2 can also be used in applications to convert SDI to DVI, and all major SMPTE standards are
supported: SMPTE 259M, 292M, 425M-A, 425M-B.
Features & Benefits:
•Supports two dual independent serial digital inputs over coax up to 3Gbps
•Supports SMPTE standard serial digital inputs as well as Evertz proprietary
•It can optionally support two dual fiber inputs via a hot pluggable SFP
•VESA video resolutions supported up to WUXGA (1920x1200/60) when using Single Link DVI
•VESA video resolutions supported up to WQXGA (2560x1600/60) when using Dual Link DVI
•Full 24 bits-per-pixel color resolution
•Ideal for use with high resolution LCD, plasma, and projection screens
•Superior digital data transmission
•Compact form factor with optional VESA mount brackets (2400VESA)
•Supports single-mode and multi-mode fiber optic cable (contact factory for multi-mode applications)
•Two stereo analog audio outputs
•SNMP enabled for configuration.
•HDCP compliant

2431RX-2
Dual Path Serial Digital to DVI Converter
Page - 2 Revision 1.0 OVERVIEW
A CHANNEL
SERIAL TO
PARALLEL
BLOCK
AUDIO
DE-
EMBEDDERS
DVI-D
OUTPUT 1
B CHANNEL
SERIAL TO
PARALLEL
BLOCK
AUDIO
DE-
EMBEDDERS
DVI-D
OUTPUT 2
CH1 Analog out
or CH 1&2 AES
out
CH2 Analog out
or CH 1&2 AES
out
Optical SFP
1A
1B
2A
2B
1A
2A
Optical SFP
1B
2B
3G/1.5G
3G/1.5G
3G/1.5G
3G/1.5G
2 x 3G/1.5G
SFP OPTION
2 x 3G/1.5G
SFP OPTION CPU CONTROL /
MONITORING
SERAIL
COM
PRWERR4321
HDCP
ENCRYPTION
HDCP
ENCRYPTION
CH1 Analog out
or CH 1&2 AES
out
CH2 Analog out
or CH 1&2 AES
out
Figure 1-1: 2431RX-2 Block Diagram

2431RX-2
Dual Path Serial Digital to DVI Converter
SPECIFICATIONS Revision 1.0 Page - 3
2. SPECIFICATIONS
2.1. SERIAL INPUTS
Standard: SMPTE 259M, 292M, 424M and Evertz proprietary format (3Gbps/1.5Gbps)
Number of Inputs: 2 - total 4BNCs when in dual link reception mode
Connector: BNC per IEC 60 169-8 Amendment 2
Equalization: Automatic up to 50m
2.2. OPTICAL INPUT
Number of Inputs: 2 per single SFP (requires second SFP for dual link mode)
Connector: LC/UPC female housing
Maximum Input Power: -3dBm
Wavelength: 1310 nm to 1610nm
Optical Sensitivity: -19dBm
Fiber Size: 62µm core / 125µm overall
2.3. DVI OUTPUTS
Number of Outputs: 2
Connectors: 28 pin DVI-I
Video Resolution: Up to WUXGA (1920x1200) @ 60Hz single link
Up to WQXGA (2560X1600) @ 60Hz dual link
Color Resolution: 24 bits
Voltage Swing: 400mV minimum
Output Clock Jitter: 150ps maximum
Differential Skew: 50ps maximum
2.4. ANALOG AUDIO OUTPUT
Number of Outputs: 2 (1 stereo pair per DVI output)
Connectors: BNC per IEC 60 169-8 Amendment 2 (Includes BNC to RCA connector)
Impedance: High Impedance (> 20kΩ)
Frequency Response: ±0.1dB (20Hz to 20kHz)
THD < 0.005% (20Hz to 20kHz)
Channel Phase Difference < ±1°
SNR > 85DB
Level -20dB to +3dB
Maximum Output Level +24dBu into 10kΩloads
2.5. ELECTRICAL
Voltage: +12VDC Auto ranging 100-240V AC 50/60Hz
Power: 11 Watts

2431RX-2
Dual Path Serial Digital to DVI Converter
Page - 4 Revision 1.0 SPECIFICATION
2.6. PHYSICAL
Dimensions with mounting flanges: 7.81” L x 5.63” W x 1.75” H (199mm L x 143mm W x 45mm H)
Weight: 1 lbs. (0.45 kg)
2.7. COMPLIANCE
Electrical Safety: Power supply UL listed
Complies with CE Low voltage directive
Laser Safety: Class 1 laser product
Complies with 24 CFR 1040.10 and 1040.11 IEC 60825-1
EMI/RFI: Complies with FCC Part 15, Class A
EU EMC directive

2431RX-2
Dual Path Serial Digital to DVI Converter
INSTALLATION Revision 1.0 Page - 5
3. INSTALLATION
The 2431RX-2 is a compact module that has four BNC connectors for serial digital input, four BNC
connectors for analog audio output (BNC to RCA connector included), 4 fiber optic connectors (2 per
SFP), two DVI-I connectors for video outputs, one DB-9 serial port connector for settings and one Ethernet
connector for control and monitoring.
Figure 3-1: 2431RX-2 Rear View
3.1. POWER
The 2431RX-2 comes with an auto-ranging DC voltage adapter that automatically senses the
input voltage. Power should be applied by connecting a 3-wire grounding type power supply
cord to the power entry module on the DC voltage adapter. The power cord should be
minimum 18 AWG wire size; type SST marked VW-1, maximum 2.5 m in length. The DC
cable of the voltage adapter should be connected to the DC power jack on the rear panel. A
green LED located beside the DIP switch connector will be illuminated when there is power
applied to the 2431RX-2.
3.2. DVI-I CONNECTORS
DVI-I connector is for digital video output. The table below lists pin outs in the DVI-I connector.
Pin Signal Pin Signal Pin Signal
1
Data2-
9
Data1-
17
Data0-
2
Data2+
10
Data1+
18
Data0+
3
Data2/4 Shield
11
Data1/3 Shield
19
Data0/5 Shield
4
Data4-
12
Data3-
20
Data5-
5
Data4+
13
Data3+
21
Data5+
6
DDC Clock
14
+5V Power
22
Data5/Clock Shield
7
DDC Data
15
Ground
23
Clock+
8
Analog VSYNC
16
Hot Plug Detect
24
Clock-
C1
Analog RED
C2
Analog GREEN
C3
Analog BLUE
C4
Analog HSYNC
C5
Ground
Table 2-1: DVI-I Input Connector

2431RX-2
Dual Path Serial Digital to DVI Converter
Page - 6 Revision 1.0 INSTALLATION
Figure 3-2: 2431RX-2 Rear View – DVI-I Connectors
3.3. BNC CONNECTORS
BNC connectors are used for serial digital inputs (4 BNC connectors) and analog audio output (4 BNC
connectors).
Figure 3-3: 2431RX-2 Rear View – BNC Connectors
3.4. FIBER CONNECTORS (OPTIONAL)
2 SFP’s (SFP3R-2) are used for serial digital input over fiber.
Figure 3-4: 2431RX-2 Rear View – Fiber Connectors

2431RX-2
Dual Path Serial Digital to DVI Converter
INSTALLATION Revision 1.0 Page - 7
3.5. DB9 CONNECTOR
DB9 is a female 9 pin D connector used for connecting to a standard computer serial. The table below
shows the pin out of the female DB-9 connector.
Pin #
Name
Description
1
2
TxD
RS-232 Transmit Output
3
RxD
RS-232 Receive Input
4
5
Sig Gnd
RS-232 Signal Ground
6
7
8
9
Table 2-2: DB9 Port Pin Out
Figure 3-5: 2431RX-2 Front View – DB9 Connector

2431RX-2
Dual Path Serial Digital to DVI Converter
Page - 8 Revision 1.0 INSTALLATION
3.6. CARE AND HANDLING OF OPTICAL FIBER
3.6.1. Safety
!
Never look directly into an optical fiber. Non-reversible damage to the eye can occur
in a matter of milliseconds.
The laser modules used in the Evertz 3000MVP modules are Class I, with a maximum output power of
7mW, and a wavelength of 1310 to 1610nm.
3.6.2. Handling and Connecting Fibers

Note: Never touch the end face of an optical fiber.
The transmission characteristics of the fiber are dependent on the shape of the optical core and therefore
care must be taken to prevent fiber damage due to heavy objects or abrupt fiber bending. Evertz
recommends that you maintain a minimum bending radius of 3 cm to avoid fiber-bending loss that will
decrease the maximum attainable distance of the fiber cable.
Fiber interconnections must be made securely. The Evertz fiber optical transmitters and receivers come
with SC interconnection housings built into the module. With this style of connector, the fiber assembly
and the housing assembly can only be connected in one way and with very good repeatability. The fiber
interconnect panel that is provided with each product can be ordered with optional SC/PC, ST/PC or
FC/PC connectors. The customer is required to provide the optical fiber with the correct connectors to
connect the modules together. SC/PC, ST/PC and FC/PC interconnection housing and connectors as well
as adapters are industry standards with many available sources.
3.6.3. Making Sure the Optical Fibers are Clean
Dust particles on the ends of the optical fiber greatly increase the signal loss at interconnections, and large
dust particles can even obscure light transmission altogether. To minimize the effects of dust
contamination at the interconnections, the fiber should be cleaned each time it is mated or unmated. When
using interconnection housings to mate two optical fibers it is good practice to remove dust particles from
the housing assembly with a blast of dry air or by wiping the end of the fiber connector with the pre-
moistened tissue you received with the optical module before mating it to the module. Whenever a fiber is
unmated it must be covered immediately. Most fiber manufacturers provide a plastic boot that fits over the
ferrule body for this purpose.

2431RX-2
Dual Path Serial Digital to DVI Converter
INSTALLATION Revision 1.0 Page - 9
3.7. STATUS LEDS
The location of the status indicators are shown in below Figure 3-6.
Power When ON this LED indicates that the 2431RX-2 is receiving electrical power.
Error When On this LED indicates that unit is booting (5 sec) or unit has malfunction.
1 Indicates that the 2431RX-2 is receiving video input on BNC or Fiber 1A.
2 Indicates that the 2431RX-2 is receiving video input on BNC or Fiber 2A.
3 Indicates that the 2431RX-2 is receiving video input on BNC or Fiber 1B.
4 Indicates that the 2431RX-2 is receiving video input on BNC or Fiber 2B.
The 2431RX-2 is equipped with colored LEDs. Each color indicates signal type.
Figure 3-6: 2432TX-2 Status LEDs

2431RX-2
Dual Path Serial Digital to DVI Converter
Page - 10 Revision 1.0 INSTALLATION
3.8. USER CONTROLS
3.8.1. Dip Switches
Figure 3-7: 2431RX-2 DIP Switches
DIP Switch
Function
1
Enable deinterlacer for input 1
2
Enable deinterlacer for input 2
3
For future use
4
For future use
5
For future use
6
For future use
7
For future use
8
For future use
Table 3-3: DIP Switch Functions

Note:
The DIP switch controls are supported with firmware 1.4.X and below. 1.5.X
and higher only support configuration using SNMP and DIP switches are disabled.