Evonicfires e1800 User manual

IMPORTANT SAFETY INFORMATION:
Always read this manual rst before aempng to install or use this replace. For your safety, always comply with all warnings and safety instrucons contained in this
manual to prevent personal injury or property damage.
Please note: This product is only suitable for well insulated spaces or occasional use.
E-Series-180724
MODEL(S): e1800 / e1560 / e1500 / e1030 / e1000 / e900 / e810 / e800 / e710 /
e700 / e640 / e600 / e500

Please read these instrucons before installaon or use and keep this booklet handy for future reference.
All Evonic res products meet the requirements of the EC Direcves.
These direcves have been met by compliance with the following standards:
EN 55014-1:2006 + A2:2011 Electromagnec compability.
EN 55014-2:2015 Electromagnec compability.
EN 61000-3-2:2014 Electromagnec compability (EMC). Limits. Limits for harmonic current emissions
EN 61000-3-3:2013 Electromagnec compability (EMC). Limits. Limitaon of voltage changes, voltage uctuaons and icker
EN 60335-1:2012 + A1:2014
EN 60335-2-30:2009+A11:2012
Safety:
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilies or lack of experience and knowledge if they have
been given supervision or instrucon concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision
The instrucons shall state that the heater must not be located immediately below a socket outlet.
WARNING: in order to avoid overheang, do not cover the heater.
Children of less than 3 years should be kept away unless connuously supervised
Children aged from 3 years and less than 8 years shall only switch on/o the appliance provided that it has been placed or installed in its intended normal operang posion and they have
been given supervision or instrucon concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns. Parcular aenon has to be given where children and vulnerable people are present
CAUTION: In order to avoid a hazard due to inadvertent reseng of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a mer,
or connected to a circuit that is regularly switched on and o by the ulity
CAUTION: The LED light system shall be replaced by electrically competent personnel only (LP – These cannot be user replaceable since they will allow access to live parts)
IMPORTANT INSTRUCTIONS:

Important electrical safety:
This appliance must never be installed above or in front of a xed electric socket.
The electrical socket must be easily accessible to isolate the supply during maintenance and cleaning.
This appliance is supplied with a two meter power lead, which has a 13Amp moulded three pin plug to connect to a standard 230/240V plug socket.
This appliance must always be earthed. If in any doubt consult a suitably competent person.
Replacement plug: (Please note that it will invalidate your warranty if the moulded plug is removed and connected to a fused spur by an unqualied person).
General Warnings:
Never leave children unsupervised with an unguarded heater.
Never obstruct or cover the heater outlet.
Never install or use this product where it may come in contact with water i.e. a bathroom or wet room.
Never use aerosols or steam cleaners near this product.
Never route the electric cable near the heater outlet.
Never route the electric cable under carpets or oor coverings.
Never install this product close to curtains or combusble materials.
Never Use the heater to dry clothes or other objects.
Never remove the replace surrounding without isolang the electric supply.
Fig:1.
This appliance must only be connected to a 230/240 Volts AC 50Hz supply. Before connecng the re, check that the supply voltage is the same as stated on the re.
This appliance must only be used on a AC supply, fuse rang 13Amp.
The wires in the mains lead are coloured in accordance with a standard UK supply, these being:
GREEN/YELLOW – EARTH
BLUE – NEUTRAL
BROWN – LIVE
As the colours of the mains lead of this appliance may not match the coloured markings used to idenfy the terminals in a plug, please observe the following (Fig:1).
• The green and yellow wire must be connected to the terminal in the plug which is marked with the leer E or Earth symbol.
• The blue wire must be connected to the terminal in the plug which is marked with the leer N.
• The brown wire must be connected to the terminal in the plug marked with the leer L.
• Replace fuses only with fuses of the correct size and rang.

This product has been designed to be installed into a plaster board, or exisng masonry chimney breast.
Please note that any GF2 models from the e-series range are not suitable to be installed into a exisng chimney breast.
Please seek advice from a professional, with reference to the structural integrity of the installaon site.
if the products is to be installed into a open chimney or ue, it is important that the chimney/ue is blocked o to prevent any up/down draughts and falling debris which could restrict
and alter the airow to the product.
It is also important to ensure that the product has a minimum internal clearance directly above and below the product of 50mm, this is to ensure that the product can circulate the re-
quired airow for the heater unit.
The product should never be sealed into a opening with the use of silicones or adhesives as this can also alter the airow and hinder any further servicing of the product.
INSTALLATION METHOD:
Installing Product:
Each E-Series product is supplied complete with one or more wall mounng brackets. (Dependent on Model)
Establish the desired nished height from oor level to the boom of the plaster kit of the product.
Fix the wall bracket to the wall ensuring to use the correct hardware xings given the wall construcon, Plaster board or Solid Wall.
Li and hook the product onto the wall bracket and secure using the wall brace brackets.
Once the product is secured to the wall and connected to the power supply, the false construcon such as plaster board wall or chimney breast can be formed around it.
It is important to allow for the nished face board when seng the depth of the frame construcon.
It is essenal to include header/Lintel at the required height to ensure the appliance does not support the weight of the nished wall.
Prepare the Cut-Out in the Plaster-board or Finishing Board, and install ensuring that the plaster kit edges are ng to the inside of the Cut-out of the board.

The above table contains the minimum opening sizes re-
quired to house the product.
Please refer to technical specicaon table for further informaon, with reference aperture measurements.
Please see Figure 1: as a example of a installaon.
Figure 1:
Model WDH
e500 530mm 305mm 610mm
e600 690mm 185mm 640mm
e640 508mm 185mm 845mm
e700 680mm 185mm 480mm
e710 760mm 185mm 790mm
e800 835mm 305mm 790mm
e810 866mm 305mm 1209mm
e900 886mm 185mm 695mm
e1000 1055mm 185mm 475mm
e1030 1065mm 305mm 560mm
e1500 1565mm 305mm 560mm
e1560 1566mm 305mm 810mm
e1800 1785mm 305mm 615mm
Model WDH
e500 495mm 305mm 400mm
e600 637mm 185mm 455mm
e640 460mm 185mm 655mm
e700 640mm 185mm 285mm
e710 710mm 185mm 607mm
e800 802mm 305mm 590mm
e810 810mm 305mm 1003mm
e900 836mm 185mm 492mm
e1000 1003mm 185mm 275mm
e1030 1003mm 305mm 355mm
e1500 1505mm 305mm 355mm
e1560 1509mm 305mm 605mm
e1800 1750mm 305mm 410mm
The below table contains the nal nished opening sizes once
the product has been installed.

Glass Removal:

The Appliance is operated using the E-Touch App Control.
The App Control can be used on either OS or Android operang systems.
To obtain the App please visit either the OS App Store Or Google Play and follow the on screen instrucons.
Screen shot taken from Apple App Store. Home Screen shot taken from E-Touch App

Product Operaon:
The appliance is operated by the e-touch App, the main standby power switch to the e-series product is located to the right of the heater outlet, which is marked with a light bulb image, to
acvate the product, this switch must be switch to the “ON” posion.
The rst me the e-series product is acvated both the illuminaon and heater will funcon, to switch the heater “O” simply reduce the Room Temperature down to 10 degrees on the
App control.
BUILT IN MODELS:
This product has been designed to be installed into a studwork or exisng chimney breast.
Please note that any GF2 models from the e-series range are not suitable to be installed into a exisng chimney breast.
Please seek advice from a professional, with reference to the structural integrity of the installaon site.
If the products is to be installed into a open chimney or ue, it is important that the chimney/ue is blocked o to prevent any up/down draughts and falling debris which could restrict
and alter the airow to the product.
It is also important to ensure that the product has a minimum internal clearance directly above and below the product of 100 mm, this is to ensure that the product can circulate the
required airow for the heater unit.
The product should never be sealed into a opening with the use of silicones or adhesives as this can also alter the airow and hinder any further servicing of the product.
Please refer to technical specicaon table for further informaon, with reference to measurements.
(Heater unit cut-out) (This is a safety feature, to safe guard against further damage to the product).
If the airow is restricted the heater will automacally turn o. This is can occur due to incorrect installaon or obstrucon.
To reset the heater funcon:
•isolate from the mains power supply.
•Leave product to cool.
•Aer a suitable cooling down period, remove the obstrucon if obstructed, and check installaon.
•Aer 10 minutes the thermo switch (cut-out) in the heater will reset.
Please note that both the eect fan and heater fan omit a low decibel noise, both of which are normal operang characteriscs.

LOG LENGTH
A260MM
B370MM
C230MM
D185MM
E190MM
F390MM
e1000/1030 —LOG LAYOUT
e1500/1800 —LOG LAYOUT
LOG SET
Please Note: The images shown are suggested Log layouts, the log sets can
be arranged to personal preference.

Condions of warranty:
If this appliance should prove to be defecve due to faulty design, materials or workmanship within 12 months of purchase, the product will be repaired free of charge, subject to the
following condions:
The electric re shall have been purchased and used solely within the UK and Ireland for domesc purposes and in accordance with the Users operang instrucons.
It is the purchasers responsibility to prove that the unit is under warranty, e.g. receipt of purchase.
All warranes, will be invalidated if unauthorised repairs or modicaons are made to the electric re, or in case of accident, misuse or damage caused by improper installaon, or to
damage occurring during transit to or from the repairer and altered or missing serial numbers.
Any parts, which have been replaced under this warranty, shall become our property.
CK Fires Ltd / Evonic Fires
1 Evonic house, Clifford park, Clifford lane, Stratford-Upon-Avon, CV37 8HW
Tel: [phone] Fax: [phone]
Email: [email protected] — Follow us on Twitter @evonicfires
Problem solving
• No power to the re: Check the wall socket, plug and fuse.
• No illuminaon: Make sure the re is turned on. Check heater is working, if so check that the dimmer control is set to full on the e-touch app/e-touch controller.
• Illuminaon but no heat: The safety cut has operated see note on operang the Fire.
• Noise when illuminated: Due to moving parts, the electric re will make a noise.
• Noise from the heater when in use: The sound of rushing air is normal.
Registering product:
To register a product please visit: www.evonicres.co.uk and complete the elds required under the Register a Product Secon.
Report a fault:
If a product is encountering a fault with the operaon and a Service Engineer is required, Please visit: www.evonicres.co.uk and complete the elds required under the Report a Fault
Secon.