Exsys EX-1309-9 User manual

1
Congratulation on your purchasing this high performance 4-port
RS232/422/485 3-in-1 to USB2.0 Adapter Cable. It supports 1 serial port which
can be set in RS232, RS422, RS485-2W, or RS485-4W modes. The UART based
serial port is fully compatible with most of the RS232C, RS422 and RS485
devices available from the market. It is an ideal solution for most of serial
applications.
Features:
USB 2.0 Full Speed (12Mbps) Compatible
Supports 1x DB9-Male-Connector RS232/422/485 3-in-1 Serial Port
Supports 4-wire RS422, RS485 and 2-wire RS485 Modes
Supports RS485 Auto Transceiver Turn Around by Unique Featured ATTATM
Hardware
Supports Baud Rate up to 921.6Kpbs
Supports Win2000, XP, 2003, 2008, Vista, Win 7, 8.x, 10, Linux and others
EX-1309-9
RS232/422/485 3-ini-1 to USB2.0 Adapter Cable,
w/ DB9M Connector
1. Introduction
2. Connector Layout
USB Type-A
Plug
DB9M Connector
(R232/422/485)
Mode
Selection
Switch

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector
2
There is an eight 8-pin DIP switch next to the connector for changing the
operating modes, enable/disable terminator and the bias for transmitter and
receiver signals.
1. Mode Settings:
The DIP switch has 8 pins, the first 3 pins (M0, M1, M2) are for mode settings
(RS232, RS485-2wire, RS485-4wire or RS422 modes), pin 4 (TERM) is to enable or
disable terminator. Pin 5 and 6 (T+, T-) is for biasing TX+ and TX- signals. Pin 7
and 8 (R+, R-) is to enable or disable bias for RX+ and RX- signals.
Note: Pin 4 to 8 are designed for RS422 and RS485 only and should be
set to OFF when you are setting the port to RS232 mode.
Modes
Settings
M0
M1
M2
(ON)
RS232
3. Mode Switch Settings

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector
3
RS485-2W
(Default)
RS485-4W
RS422
2. Termination Resistor Settings:
The pin 4 of the DIP switch is to enable the 120 Ohm termination resistor
between RX+ and RX- signals.
DIP Switch Pin 4
DIP Switch Pin 4
RS485-2wire mode:
RS485-4wire or RS422 mode:

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector
4
Terminator disabled (OFF, default) Terminator enabled (ON)
3. Bias Resistors Enable/Disable:
Pin 5 to 8 of the DIP switch are to enable (ON) or disable (OFF) the 4 bias
resistors for TX+, TX-, RX+, RX- signals respectively. Please note that you have to
set them to OFF if you are setting the port in RS232 mode.
Disable (default) all 4 Bias resistors for TX+, TX-, RX+ and RX-:
DIP Switch Pin 5
DIP Switch Pin 6
DIP Switch Pin 7
DIP Switch Pin 8

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector
5
Enable all 4 Bias resistors for TX+, TX-, RX+ and RX-:
1.
This Adapter Cable can be hot-plugged to the USB port of your computer
due to the specifications of USB. It supports the following operating systems.
The drivers were shipped in the following folders on the supplied driver CD.
1. Driver Locations on the CD
These instructions are for installing the drivers from the CD supplied with the
product. If you are installing drivers for Windows, when prompted for the
location of the drivers, specify your DVD drive and the locations according to
the following folder list:
4. Software Installation

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector
6
2. Installing Drivers for (32-bit and 64-bit) Win7, 8.x, 10, XP, Vista,
2008, 2003 and 2000:
Insert the Driver CD supplied with the Adapter Cable.
Run (or double click) the Installer Program (e.g.CDM20824.exe ) in
the following folder of the driver CD:
\USB_to_IO\FTDI\(32_64bit)Win7_8_XP_Vista_2008_2008R2_2003
_2000
Follow the instructions of the installer program to complete the setup
procedures.
Plugging the Adapter Cable will hook the drivers into the Windows
kernel automatically.
The pin assignment of the DB9 male connector of the Adapter Cable is
dependent on its operation modes. Please refer to the following figure for the
corresponding mode:
1. RS232 Pin Assignment:
RS232 DB9(Male) to DB9(Male) Wiring:
5. Connector Pin Assignments
DB9 Male(Adapter Cable) DB9 Male(Serial Device)
1 DCD 1 DCD
2 RXD 2 RXD
3 TXD 3 TXD
4 DTR 4 DTR
5 GND 5 GND
6 DSR 6 DSR
7 RTS 7 RTS
8 CTS 8 CTS

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector
7
2. RS422 and RS485-4wire Pin Assignment:
RS422 Cable Wiring:
3. RS485-2wire Pin Assignment:
RS485-2wire Cable Wiring:
DB9 Male (Adapter Cable)
1 TXD-
2 TXD+
3 RXD+
4 RXD-
5 GND
(RS422 Device)
1 TXD-
2 TXD+
3 RXD+
4 RXD-
5 GND
DB9 Male (Adapter Cable)
1 DATA-
2 DATA+
5 GND
(RS485 Device)
1 DATA-
2 DATA+
5 GND

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector
8
Type
Specifications
Device Connector
Cable
Host Connector
Number of Ports
RS-232 Signals
RS422 Signals
RS485-4wire Signals
RS485-2wire
Baud Rate
Data Bits
Stop Bits
I/O address/IRQ
Parity
Flow Control
Power Requirement
Operating Temperature
Operating Humidity
Storage Temperature
DB9 male
USB
USB Type-A
1
TXD, RXD, RTS, CTS, DTR, DSR, DCD, GND
TXD+, TXD-, RXD+, RXD-, GND
TXD+, TXD-, RXD+, RXD-, GND
DATA+(B)/DATA-(A)
110 bps to 921.6Kbps
5,6,7,8
1, 1.5, 2
Plug-and-Play (various)
None, Even, Odd
RTS/CTS, XON/XOFF
5V/110mA (USB Bus Powered)
0°C to 55C(32 to 132F)
5 to 95% RH
-20°C to 85C (-4 to 185F)
5. Specifications