FabiaTech FP8100 Series User manual

Version 1.1 FP8100 Series User’s Quick Reference Page 1/3
www.fabiatech.com ©2009-2010 FabiaTech Corporation
1. Brief
The FP8100x is a 10-inch Panel PC with touch screen device (FP8100xT). This user’s quick reference
provides its outlook information and I/O outlets description.
2. Dimensions (in mm) and Rear I/O Informations
3. Packing List
1 FP8100x/FP8100xT industrial Panel PC.
1 AC to DC19V power adapter and 1 AC power code cable.
1 pack of 2.5” SATAHDD installing kit with 4+2 screws.
1 Y-cable (3-end) keyboard plus mouse port adapter cable.
1 pack of Wall Mounting Kit with 4 fixed screws.
1 pack of Embedded Mounting Kit with 6 clamps and 6 fixed screws.
1 pack of panel stand kit with 4 fixed screws. (FP8100K1, optional)
1 touch pen for touch screen panel (Optional)
1 Compact Disc including user’s manual and touch screen drivers.
4. Features
* Processor Board
AMD Geode LX800 processor with 1GB DDR RAM.
* I/O Outlets
One 10/100 base-TX Ethernet port.
2 USB ports (V2.0) and 2 RS-232 serial ports.
1 VGA (CRT) and 1 PS/2 compatible keyboard/mouse interface.
2 Audio connectors for Earphone and Microphone.
1 mini PCIe card socket for wireless/GPRS modules.
1 DC-In plug connector for DC power input.
1 power button and 1 reset button.
* Storage Bay
1 CompactFlash socket for CompactFlash modules or MicroDrives.
One 2.5" SATA hard disk space.
* Power requirement
+12 ~ +24V DC, 1.44A maximum (0.92A typical) with 19V input voltage.
* Mechanical
Dimensions: 54mm(D) x 308mm(W) x 222mm(H)
Weight: 3.5Kg.(Standard packing)
Approval: IP65 Compliant.
5. I/O outlets and LED Indicator
A. Power Connector and I/O Connectors Group #1 (COM2, Keyboard/Mouse, and USB)
DC +12V to +24V, 35W minimum
DC Plug-In Connector
Keyboard
(
& Mouse
)
COM1 USB#1 & #2
Note: Standard PS/2 keyboard can be plugged into this
connector without any adapter cable. If PS/2
keyboard and mouse will be used simultaneously,
the included Y-type adapter cable is needed.
308
222 53.6
75
75
75
276.2
191
MIC
RESET
CRT
LAN
KB/MOUSE
COM2
DC IN 12~24V
POWER SWITCH
1
2/
ON
OFF
SPK OUT
COM1
USB

Version 1.1 FP8100 Series User’s Quick Reference Page 2/3
www.fabiatech.com ©2009-2010 FabiaTech Corporation
B. I/O Connectors Group #2 (LAN, COM1, VGA, and Audio)
6. Installation
A. Installing the Wall Mount Kit and Panel Stand Kit
B. Open the Cover for installing 2.5” HDD, CompactFlash, DDR RAM, WLAN, and Antenna
C. Installing DDR, HDD, CF, mini Card, SIM, Antenna, and Battery (RTC & CMOS Ram)
COM1
LAN
Note : The LAN port is a RJ45 connector with 2 LEDs. The orange LED indicates data is accessing
and the green LED indicates on-line status.
VGA
(
D-sub 15
)
Earphone
(Line-Out) Mic-In
DDRSODIMM
DDRSODIMM
CF
FB6604 CPU
Board Install DDR RAM Module
4 screws
Wall Mounting Kit (4 Screws)
A
lso including VESA 75mm Standard Panel Stand Kit (4 Screws)
FP8100K1 (optional)
Step 1: Separate the back cover
from housing (10 screws)
Step 2: Separate the I/O cover
from housing (9 screws)
Step 3: Remove FB6604
CPU board (2 screws)
Install mini Card Module
(
1/2
)
Install theAntenna
Install the SIM Card (1/3)
Install mini Card Module (2/2)
Install the CompactFlash Module
Install the 2.5” HDD (1/2)
Install the 2.5” HDD (2/2)
Install the SIM Card (2/3)
Install the SIM Card (3/3)
2 screws
Install the Battery (2 screws)
2 screws

Version 1.1 FP8100 Series User’s Quick Reference Page 3/3
www.fabiatech.com ©2009-2010 FabiaTech Corporation
D. Installing the Embedded Mounting Kit (6 Clamps and 6 Screws)
End of Document
Step 1 Step 2
WALL
Cut out dimension 278.2 x 193mm
WALL