Factoryfurniture Osso3 Manual

factoryfurniture.co.uk
Osso3Bench
OPERATION & MAINTENANCE MANUAL

factoryfurniture.co.uk
Introduction
Design
Design, shop drawings and development by
Factory Furniture Ltd.
Manufacture
Factory Furniture manufactured components. Products
are assembled in Factory workshops, checked and
dispatched ready for installation. Replacement products
or components thereof should be ordered direct from
Factory Furniture Ltd.
Copyright
The design copyright for the product and
drawing copyright remains the sole property
of Factory Furniture Ltd.
General Specifications
Osso3Bench
Metric length 2720mm | width 2385mm | height
470mm *
Imperial length 8’ 11” | width 7’ 10” | height 1’ 6½” *
Approx Weight 124kg
Fixing Centres See installation drawings at end of
manual
Detailed Material & Finish
Specifications
Main Body
• Manufactured from mild steel - hot dipped
galvanised with polyester powder coat finish
(powder coat colour grey as standard or to customer
specification)
• Bench anchored to ground using 6 no. M10 x 75mm
sleeve anchors per bench
General Maintenance
(Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of bench - check all items for superficial
or physical damage
Three Monthly
Clean all items as detailed below check all fixings are
seated correctly
Six Monthly
Secure all fixings; full clean as detailed below; check
that bench is firmly secured to the ground
Specific Maintenance Details
Polyester Powder Coated & Galvanised
For general cleaning using a damp cloth and warm
soapy water only. Scourers and abrasive cleaners are
NOT suitable for this type of finish and may damage it.
Before using any cleaning agents to remove grati etc.
try on a small, inconspicuous area first to avoid causing
more unsightly damage.
Repairs
Polyester Powder Coated & Galvanised Surfaces
For light damage (scratches, chips etc.) repair using
touch-up paint to match original colour (available
from Factory Furniture Ltd). Paint application should
be carried out in accordance with approved methods
detailed by the paint manufacturer. Please note that
it is advisable to use professional painters to achieve
best results when touching up larger areas. Products
for respraying larger areas are available from Factory
Furniture Ltd.
Heavy Damage
In the event of serious damage to any component,
replacements should be ordered from Factory Furniture
Ltd. Should further assistance be required (or if the
product needs to be disassembled for any reason),
please contact Factory Furniture for detailed technical
advice.
AutoCAD Drawing List
FF1040 / 01
OSSO3BENCH
GENERAL ARRANGEMENT DRAWING
FF1040 / 02
OSSO3BENCH
PART DETAIL DRAWINGS (MAIN BODY)
FF1040 / 03
OSSO3BENCH
PART DETAIL DRAWINGS (BASE)
FF1040 / 04
OSSO3BENCH
SETTING OUT DRAWINGS MODULE ASSEMBLY
FF1040 / 05
OSSO3BENCH
SETTING OUT DRAWINGS BASE FIXINGS

factoryfurniture.co.uk
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
Osso3Bench
(surface fix only)
1. If necessary bolt three bench elements together
using 3 no. fixing plate spacers and 12 no. M8 x
30mm button head bolts & locknuts provided.
2. Install suitable foundation pads (see illustration)
each with top face at ground level
3. Position bench in correct orientation with bases
centrally on foundation pads, then mark hole
positions through base plates.
4. Remove the bench; drill holes Ø16mm x 75mm
deep (or as bolt manufacturer’s recommendations).
Clear debris from holes.
5. Reposition bench and fix to foundation pads using
6 no. zinc-coated M10 x 75mm sleeve anchors
tightened to 50Nm (or as per manufacturer’s
instruction). Check levels
M8 x 30mm
button head
bolt & locknut
Fixing plate
as spacer
Hub plate
welded to one
of the three
bench sections

factoryfurniture.co.uk
5 Pioneer Road, Faringdon,
Oxfordshire SN7 7BU
[phone]
[email protected].uk
1590
120
(Ctrs)
120
(Ctrs)
120
(Ctrs)
1325
400 400
400
400
400
2720
470 2385
Foundation 3 no. pads
400 x 400 x 400mm in C20
concrete (recommendation only)
Ground
Level
120 (Ctrs)
75
Drill hole Ø16 x
75mm or as per
bolt manufacture's
recommendation
Foundation 3 no. pads
400x400x400mm in
C20 concrete
(recommendation only)
Rawlplug M10 x
75mm Rawl Bolt
(R-RBL-M10/10W)
or similar
470